|
|
|
|
 |
 
|
 |
BMW Garage | BMW Meets | Register | Search | Today's Posts | Mark Forums Read |
 |
|
BMW 3-Series (E90 E92) Forum
>
Shaking/limp mode
|
 |
| 06-23-2012, 06:08 PM | #1 |
|
Captain
 
79
Rep 788
Posts |
Just changed ALL my coils and plugs. Had misfires on 4,5 n 6 cylinders. I would get limp mode and some shaking if car was "cold".
Unfortunately it still does the same thing. When up to temp the car is fine. Plugs were dirty as hell. Also, the holes where plugs go into had a black residue around circumference. Either fuel or carbon??? I also get a bunch of lambda codes so I'm guessing it's the o2 sensors on bank 2 that cause misfires/limp. Btw I don't have any misfires on cold starts. Any feedback will be appreciated.
__________________
JB4 Trebila tuned cp-e IC AMS exhaust BMS DCI AR DP's METH RB TURBO
19" VMR VB3 Stoptech BBK TC KLINE VORSHLAG SPEC STG 3 OSS design |
| 06-23-2012, 06:55 PM | #3 |
|
Major General
 
161
Rep 7,377
Posts |
+100.. Really dont get how people can treat their cars like shit and go WOT cold...
__________________
07 335i AT - MOTIV 750 - MHD E85 BMS flash - BMS PI - JB4G5 - Okada Coils - NGK 5992 Plugs - Helix IC - Snow Stg. 3 - Stett CP - Custom midpipes with 100 HJS Cats - Bastuck Quad - PSS10 - QUAIFE LSD - BMS OCC - Forge DVs - AR OC - ALCON BBK - M3 Chassi - Dinan CP - Velocity M rear Toe arms - Advan RZ-DF - LUX H8 - Level 10 AT upgrade
 |
|
Appreciate
0
|
| 06-23-2012, 07:02 PM | #5 |
|
Captain
79
Rep 788
Posts |
Well I didn't mean going WOT right away after starting off. Meant like 5-10 min after driving.
But while driving on a cold start (oil temp less than 210F) I get shakes/ hesitations.
__________________
JB4 Trebila tuned cp-e IC AMS exhaust BMS DCI AR DP's METH RB TURBO
19" VMR VB3 Stoptech BBK TC KLINE VORSHLAG SPEC STG 3 OSS design |
|
Appreciate
0
|
| 06-23-2012, 07:32 PM | #6 |
|
Colonel
 
375
Rep 2,838
Posts
Drives: e92 335i, e34 525i & e60 530i
Join Date: Aug 2011
Location: N Las Vegas
|
Make sure your o2 sensors are in the correct dp if you have any. This cleared my lambda codes and shaking. Remember, gray wired one goes in the dp on the passenger side and the black wired one goes into the driver side dp. Good luck.
Here are the codes I had. 2C7F-Lambda probe after catalytic converter 2, trimming control 2C6A-Lambda probe after catalytic reversed 2C6C-Lambda probe after catalytic converter 2, system check
__________________
|
|
Appreciate
0
|
| 06-23-2012, 07:41 PM | #7 | |
|
Captain
79
Rep 788
Posts |
Quote:
__________________
JB4 Trebila tuned cp-e IC AMS exhaust BMS DCI AR DP's METH RB TURBO
19" VMR VB3 Stoptech BBK TC KLINE VORSHLAG SPEC STG 3 OSS design |
|
|
Appreciate
0
|
 |
| Bookmarks |
| Thread Tools | Search this Thread |
|
|
