Car Drive Different After Walnut Blasted :(

Bimmerprid3 · 07-13-2014, 09:59 PM

I wish you guyz can help me out. Car running fine since after a walnut blasted my car drive very poorly. Car started normally & idle were steady. When I pulled @ 2000 to 3000 rpm. Car feel sturdier. When drive on freeway @ speed of
70 to 80. Car feel sturdier again & again. Idle were fine though. There is no check engine or code from it. This all happened from a walnut blasted I got it done from some member on the forum. Thanks

924er · 07-13-2014, 10:04 PM

u sure he properly blasted it?

Bimmerprid3 · 07-13-2014, 10:14 PM

For what he told me, he done it before. The guy seem like he know what he was doing.

e92_enthusiast_1 · 07-13-2014, 10:27 PM

W/o a code its hard to tell. Might be a simple as a loose/missed hose.

Quote:

Originally Posted by Bimmerprid3

I wish you guyz can help me out. Car running fine since after a walnut blasted my car drive very poorly. Car started normally & idle were steady. When I pulled @ 2000 to 3000 rpm. Car feel sturdier. When drive on freeway @ speed of
70 to 80. Car feel sturdier again & again. Idle were fine though. There is no check engine or code from it. This all happened from a walnut blasted I got it done from some member on the forum. Thanks

Bimmerprid3 · 07-13-2014, 10:43 PM

Do you think might be a bad sensor from manifold or charged pipe???

ferocity02 · 07-13-2014, 10:57 PM

Who did it?

4doorbmwpower · 07-13-2014, 10:58 PM

besides blasting without valves at TDC what could you do durring blasting to cause issues with the car? didnt plug a sensor back in? is there something you can reverse on accident like the dreaded O2 sensors with DP swaps?

Bimmerprid3 · 07-13-2014, 11:07 PM

Some member on our forum did the walnut blasted. I did went back to him the second week. He checked out all his work & sadly the problems is still there. I want ask for help 1st before I probably have to take it to dealership

j1gilles · 07-13-2014, 11:54 PM

Quote:

Originally Posted by Bimmerprid3

Some member on our forum did the walnut blasted. I did went back to him the second week. He checked out all his work & sadly the problems is still there. I want ask for help 1st before I probably have to take it to dealership

You should at least ask for your money back... Your car ran fine prior to the walnut blasting and immediately after the blasting it runs poorly, kind of narrows down the culprit in my opinion. I have had something else go wrong after repairing someones car (i.e replace water pump and then radiator hose breaks) but this was maintenance, not a repair.

robc1976 · 07-14-2014, 12:27 AM

Sounds like intake leak, maybe not bolted down all the way?

Tiago@VRSF · 07-14-2014, 12:27 AM

I like to ask for before/after pictures when having a less credible individual do this kind of work.

The most common problem when dealing with our cars is the vacuum nipple on the intake manifold gets incredibly brittle and tends to break off when inexperienced individuals try to yank it off. Once it gets ripped off that causes a major boost leak, causes you to run rich and the car runs like crap. It also prevents your DV's from functioning correctly.

C.Pop · 07-14-2014, 12:27 AM

You should find out what's wrong before asking for your money back, lol.

robc1976 · 07-14-2014, 12:35 AM

If it's the nipple here is my DIY:

http://www.e90post.com/forums/showthread.php?t=820718

pwr hungry · 07-14-2014, 09:32 AM

Rob has diys for everything...including nipples!

Indo Rider · 07-14-2014, 10:05 AM

I literally LOLed!

evoix · 07-14-2014, 10:29 AM

Lol.

robc1976 · 07-14-2014, 12:51 PM

Roflmao!

07-13-2014, 09:59 PM	#1
Bimmerprid3 Private First Class 5 Rep 177 Posts Drives: Bmw 335I Coupe Join Date: Mar 2007 Location: Orange County iTrader: (5)	Car Drive Different After Walnut Blasted :( I wish you guyz can help me out. Car running fine since after a walnut blasted my car drive very poorly. Car started normally & idle were steady. When I pulled @ 2000 to 3000 rpm. Car feel sturdier. When drive on freeway @ speed of 70 to 80. Car feel sturdier again & again. Idle were fine though. There is no check engine or code from it. This all happened from a walnut blasted I got it done from some member on the forum. Thanks
	Appreciate 0 Tweet Quote

07-13-2014, 10:04 PM	#2
924er Colonel 352 Rep 2,049 Posts Drives: e92 335i '10 Join Date: Feb 2014 Location: Socal iTrader: (0)	u sure he properly blasted it?
	Appreciate 0 Quote

07-13-2014, 10:14 PM	#3
Bimmerprid3 Private First Class 5 Rep 177 Posts Drives: Bmw 335I Coupe Join Date: Mar 2007 Location: Orange County iTrader: (5)	For what he told me, he done it before. The guy seem like he know what he was doing.
	Appreciate 0 Quote

07-13-2014, 10:43 PM	#5
Bimmerprid3 Private First Class 5 Rep 177 Posts Drives: Bmw 335I Coupe Join Date: Mar 2007 Location: Orange County iTrader: (5)	Do you think might be a bad sensor from manifold or charged pipe???
	Appreciate 0 Quote

07-13-2014, 10:57 PM	#6
ferocity02 Colonel 553 Rep 2,085 Posts Drives: 2013 135is Join Date: May 2014 Location: USA iTrader: (8)	Who did it?
	Appreciate 0 Quote

07-13-2014, 10:58 PM	#7
4doorbmwpower Captain 63 Rep 954 Posts Drives: Montego Blue E90 335i Join Date: Nov 2010 Location: North Carolina iTrader: (3)	besides blasting without valves at TDC what could you do durring blasting to cause issues with the car? didnt plug a sensor back in? is there something you can reverse on accident like the dreaded O2 sensors with DP swaps? __________________ cp-e GTX3071R TT kit, cp-e quad exhaust, cp-e fuelbar, Stage 3 LPFP+lines, AEM EFI, Custom Meth kit, Apex EC7 18s w/R888 295s, Stoptech, M3 front, m-sport rear, cp-e difuser, Custom Headlights, CFS Radiator, Custom OC, 1000hp Lvl10 trans, DSS Axles, MFactory LSD, DEFIV lockdown kit, M3 refresh kit, KWv2's, cp-e project "4doorbmwpower"
	Appreciate 0 Quote

07-13-2014, 11:07 PM	#8
Bimmerprid3 Private First Class 5 Rep 177 Posts Drives: Bmw 335I Coupe Join Date: Mar 2007 Location: Orange County iTrader: (5)	Some member on our forum did the walnut blasted. I did went back to him the second week. He checked out all his work & sadly the problems is still there. I want ask for help 1st before I probably have to take it to dealership
	Appreciate 0 Quote

07-14-2014, 12:27 AM	#10
robc1976 DIYER 638 Rep 5,521 Posts Drives: E90 335i Join Date: Mar 2012 Location: Illinois iTrader: (14)	Sounds like intake leak, maybe not bolted down all the way? __________________ JB4 G5, Stage 3 LPFP, Stage 2 MOTIV PI, VM 6466 ST, Custom OCC W/ SS lines, ER FMIC, ER CP W/HKS BOV, M3 control arms, M3 guide rods, M3 upper links, M3 front & rear sway-bars, HPA rear toe arms, Wavetrac LSD, HPF Gen 2, DEFIV kit, KW clubsport, Delrin solid SF bushings, stoptech rotors, Rogue Tranny Mounts, 1M bumper, M3 CF hood, M3 fenders, M3 OEM sideskirts, Mtech rear bumper, CSL trunk, MORR VS8.2 rims 245/295
	Appreciate 0 Quote

07-14-2014, 12:27 AM	#11
Tiago@VRSF 2108 Rep 43,350 Posts Drives: F90 M5 Join Date: Dec 2007 Location: Doral, FL iTrader: (99) Garage List 2014 F30 328xi [0.00] 2015 F82 BMW M4 [0.00] 2013 Ducati 1199 Pa ... [0.00] 2008 BMW 335i [0.00]	I like to ask for before/after pictures when having a less credible individual do this kind of work. The most common problem when dealing with our cars is the vacuum nipple on the intake manifold gets incredibly brittle and tends to break off when inexperienced individuals try to yank it off. Once it gets ripped off that causes a major boost leak, causes you to run rich and the car runs like crap. It also prevents your DV's from functioning correctly.
	Appreciate 0 Quote

07-14-2014, 12:27 AM	#12
C.Pop First Lieutenant 65 Rep 385 Posts Drives: 335i Join Date: May 2013 Location: AZ iTrader: (0)	You should find out what's wrong before asking for your money back, lol. __________________ 2007 E90, 6MT, VRSF 7" FMIC, RR DP's, Vargas Stage 2+ (19t unclipped), CP-e Charge Pipe/Tial BOV, BMS DCI, Fuel-it! Stg 2 LPFP, E66, 118k+ miles Brentuned
	Appreciate 0 Quote

07-14-2014, 12:35 AM	#13
robc1976 DIYER 638 Rep 5,521 Posts Drives: E90 335i Join Date: Mar 2012 Location: Illinois iTrader: (14)	If it's the nipple here is my DIY: http://www.e90post.com/forums/showthread.php?t=820718 __________________ JB4 G5, Stage 3 LPFP, Stage 2 MOTIV PI, VM 6466 ST, Custom OCC W/ SS lines, ER FMIC, ER CP W/HKS BOV, M3 control arms, M3 guide rods, M3 upper links, M3 front & rear sway-bars, HPA rear toe arms, Wavetrac LSD, HPF Gen 2, DEFIV kit, KW clubsport, Delrin solid SF bushings, stoptech rotors, Rogue Tranny Mounts, 1M bumper, M3 CF hood, M3 fenders, M3 OEM sideskirts, Mtech rear bumper, CSL trunk, MORR VS8.2 rims 245/295
	Appreciate 0 Quote

07-14-2014, 09:32 AM	#14
pwr hungry Banned 42 Rep 1,257 Posts Drives: 335 Join Date: Mar 2013 Location: Amer'ca iTrader: (2)	Rob has diys for everything...including nipples!
	Appreciate 0 Quote

07-14-2014, 10:05 AM	#15
Indo Rider Captain 630 Rep 787 Posts Drives: 135 Join Date: Apr 2012 Location: United States iTrader: (0)	I literally LOLed!
	Appreciate 0 Quote

07-14-2014, 10:29 AM	#16
evoix Major 464 Rep 1,449 Posts Drives: X3m Evo IX Evo X Join Date: Jan 2014 Location: NY iTrader: (0)	Lol.
	Appreciate 0 Quote

07-14-2014, 12:51 PM	#17
robc1976 DIYER 638 Rep 5,521 Posts Drives: E90 335i Join Date: Mar 2012 Location: Illinois iTrader: (14)	Roflmao! __________________ JB4 G5, Stage 3 LPFP, Stage 2 MOTIV PI, VM 6466 ST, Custom OCC W/ SS lines, ER FMIC, ER CP W/HKS BOV, M3 control arms, M3 guide rods, M3 upper links, M3 front & rear sway-bars, HPA rear toe arms, Wavetrac LSD, HPF Gen 2, DEFIV kit, KW clubsport, Delrin solid SF bushings, stoptech rotors, Rogue Tranny Mounts, 1M bumper, M3 CF hood, M3 fenders, M3 OEM sideskirts, Mtech rear bumper, CSL trunk, MORR VS8.2 rims 245/295
	Appreciate 0 Quote

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search