[Beau93315]

Does anyone ever see above 22.1 psi? We have tried several things and different firmware versions with no luck on our logs. In the past a long time ago ~2012 when Shiv was posting logs he had one that was showing 23psi?


Do you ever see above 22.1psi(stock map sensor) in your logs? What firmware are you running?


Thanks!

[3000GT MR]

Originally Posted by Beau93315

Does anyone ever see above 22.1 psi? We have tried several things and different firmware versions with no luck on our logs. In the past a long time ago ~2012 when Shiv was posting logs he had one that was showing 23psi?


Do you ever see above 22.1psi(stock map sensor) in your logs? What firmware are you running?


Thanks!

Aem 3.5 map sensor installed correctly? Log map2 and see what that says

[Beau93315]

Originally Posted by 3000GT MR

Aem 3.5 map sensor installed correctly? Log map2 and see what that says

No luck, we have an alternative way of it getting to our target but the logs do not show. Even yours does not show above it :S at least from the logs you sent Tom.

[3000GT MR]

Originally Posted by Beau93315

No luck, we have an alternative way of it getting to our target but the logs do not show. Even yours does not show above it :S at least from the logs you sent Tom.

I've never sent my logs to anyone, but yes my boost does read above 21.5 in fact it reads to 26.5psi but that's calculated. The only true map pressure is from the aem map sensor logged under channel map2 which is raw data. That's the only pressure reading I use to tune. Boost doesn't mean anything above 18psi per the procede

[3000GT MR]

Boost tends to read higher than actual (Map2)

EDIT: Iv'e tuned a lot of ST procedes and every single one of them read like mine does. You have a wiring issue with your sensor or haven't loaded the correct firmware or map for ST and/or someone is messing with it that doesnt know how the procede changes with the ST FW/Map. A lot of settings get changed or change function when going ST

['___']

Originally Posted by Beau93315

No luck, we have an alternative way of it getting to our target but the logs do not show. Even yours does not show above it :S at least from the logs you sent Tom.

If you're alternative way works so well, then why are you here asking questions? Chris has given you the answer you're looking for. If you really want it to work with the procede, I suggest you do what he says. With shiv gone, chris is your best bet by far.

[Beau93315]

Originally Posted by 3000GT MR

Boost tends to read higher than actual (Map2)

EDIT: Iv'e tuned a lot of ST procedes and every single one of them read like mine does. You have a wiring issue with your sensor or haven't loaded the correct firmware or map for ST and/or someone is messing with it that doesnt know how the procede changes with the ST FW/Map. A lot of settings get changed or change function when going ST

I will update you as I go along, it easily could be firmware I have not used yours yet still going through what Robert sent me. This wasn't anything ment to piss anyone off or rant at anyone I was just asking how other peoples performed?

EDIT: We are going to load your firmware and work with that tomorrow or friday I will send you some logs after

Originally Posted by '___'

If you're alternative way works so well, then why are you here asking questions? Chris has given you the answer you're looking for. If you really want it to work with the procede, I suggest you do what he says. With shiv gone, chris is your best bet by far.

It does run for the time being, but not where it is supposed to be you are coming into something you have no idea about no need to dickride. I have contacted them with no luck and they dont even know what firmware to run LOL, and I have updated Chris with everything we have done so far all wiring is correct(according to what Robert sent me wiring diagram etc) there is just something not functioning right, I mean I even replaced the AEM sensor lol. ALSO I have done nothing but thank Chris for all his help and support.

I don't know what your problem is but get over yourself

[Tzu]

Originally Posted by Beau93315

Do you ever see above 22.1psi(stock map sensor) in your logs? What firmware are you running?


Thanks!

I'm confused. Are you running the AEM 3.5 bar sensor?

['___']

Originally Posted by Beau93315

I will update you as I go along, it easily could be firmware I have not used yours yet still going through what Robert sent me. This wasn't anything ment to piss anyone off or rant at anyone I was just asking how other peoples performed?

EDIT: We are going to load your firmware and work with that tomorrow or friday I will send you some logs after




It does run for the time being, but not where it is supposed to be you are coming into something you have no idea about no need to dickride. I have contacted them with no luck and they dont even know what firmware to run LOL, and I have updated Chris with everything we have done so far all wiring is correct(according to what Robert sent me wiring diagram etc) there is just something not functioning right, I mean I even replaced the AEM sensor lol. ALSO I have done nothing but thank Chris for all his help and support.

I don't know what your problem is but get over yourself

Chris and I are good buddies. So, I would say you're the one speaking without knowledge if what is going on. As far as the discrepancies go between Robert and Chris...i would do what Chris says. He has dug into the procede capabilities and tables far more than Shiv did. I say this because Shiv's single turbo tuned cars don't run nearly as smooth as Chris's do. So, trust me, no dick riding here, just giving credit where credit is due and suggesting you do what he says to save yourself lots of headaches.