[Turbo_power4ever]

I just flashed my car. I know the ses light is normal but my car started to go crazy. All the lights came on and the car was shaking and barely moved. I turned it off and back on and now it seems ok. Is that normal?

[335NJ]

Did you follow the instructions for what to do after flashing? Turn off console, remove key, insert key, start car.

Also, are you using a JB4 with the flash or standalone?

[Turbo_power4ever]

Originally Posted by 335NJ

Did you follow the instructions for what to do after flashing? Turn off console, remove key, insert key, start car.

Also, are you using a JB4 with the flash or standalone?

Yea i did follow instructions. And yea its the jb4 with the *********** e85 flash.

[csu87]

Did you set the jb4 to 4/2? Did you flash the correct file

[Turbo_power4ever]

Yea. Well actually my see light is now off. And car seems to be running fine.... Hmmm maybe it works now??

[Turbo_power4ever]

O sweet jesus... Yea i think it worked. Its pulling harder than ever with e50. Yea it was probably just adjusting or something when it stuttererd???

[335NJ]

Originally Posted by csu87

Did you set the jb4 to 4/2? Did you flash the correct file

This, and don't forget to set all AFR/DUTY bias values to 0..

[Turbo_power4ever]

Originally Posted by 335NJ

This, and don't forget to set all AFR/DUTY bias values to 0..

Yea i set them all to zero. The afr bias. And i went to 4/2. Then i went to map 2 which is for 17 psi, but im only hitting 12 and its right on target. Then i tried map 1 and 10 psi was target.? I thought for a minute it was working. The flash said it was complete. Took like 10 minutes. I flashed the jb4_i8a0s_e85.bin mines a 07

[Turbo_power4ever]

It seems to pull a bit harder but the psi is not correct. I bought my jb4 last year so it should be g5 iso right?

[Turbo_power4ever]

Originally Posted by 335NJ

This, and don't forget to set all AFR/DUTY bias values to 0..

Wait? Im suppose to set the duty bias to zero also?

[335NJ]

Originally Posted by Turbo_power4ever

Wait? Im suppose to set the duty bias to zero also?

Yes. Read Terry's notes above the firmware updates.

[Turbo_power4ever]

Originally Posted by 335NJ

Yes. Read Terry's notes above the firmware updates.

Yea i changed it to zero now. It did not state that on the flash directions. Its still not targeting the higher boosts on map 1,2 and 7 though..?? I double checked that it was on 4/2

[335NJ]

What firmware on the JB4 are you using?

[Turbo_power4ever]

Originally Posted by 335NJ

What firmware on the JB4 are you using?

This it?

[335NJ]

Originally Posted by Turbo_power4ever

This it?

Upload VER. 30, set all Duty bias to 0, set N20 to 0, set all cylinder logging to 4 or 5, set 3rd gear boost limitation to 0, set meth trigger to 0 unless you're using meth, and set boost safety to 19.

Read this throughly: http://www.n54tech.com/forums/showthread.php?t=17441

[Turbo_power4ever]

Originally Posted by 335NJ

Upload VER. 30, set all Duty bias to 0, set N20 to 0, set all cylinder logging to 4 or 5, set 3rd gear boost limitation to 0, set meth trigger to 0 unless you're using meth, and set boost safety to 19.

Read this throughly: http://www.n54tech.com/forums/showthread.php?t=17441

Ok i will try this later tonight. Thanks. I tried to read as much info as i could. I already downloaded the hex file i just got to update and install it. Hope that works

[335NJ]

Originally Posted by Turbo_power4ever

Ok i will try this later tonight. Thanks. I tried to read as much info as i could. I already downloaded the hex file i just got to update and install it. Hope that works

With that many values and things not set properly, it should be 100x better

[Turbo_power4ever]

Originally Posted by Turbo_power4ever

Ok i will try this later tonight. Thanks. I tried to read as much info as i could. I already downloaded the hex file i just got to update and install it. Hope that works

Ok thanks alot guys. I appreciate your help.

[335NJ]

Originally Posted by Turbo_power4ever

Ok thanks alot guys. I appreciate your help.

No problem