[BOosted 335i]

I have my er chargepipe with 2 meth bungs I'd say little close to each other.they are 1-1/2 inches on center apart.i want to run a cm10 & cm05 setup.right now I have a cm14 single.its been fine and logs are fine but don't want to chance it.do they sell a kit where I can drill a hole in chargepipe,add a bung style to fit or do I have to get it welded on? Unless the spacing is ok then I'll leave it.looking for opinions thanks.

[Jeff@TopGearSolutions]

You'd need to have a bung welded on.

Or if you order a new charge pipe from ER, they can weld you as many bungs as you want with a custom pipe.

The spacing is OK, I ran 2 bung with the same pipe. M5 and M7 specifically. The car was much more responsive with the 2 meth bung 5 and 7 VS M12 and M14 I was using previously.

[BOosted 335i]

Originally Posted by Jeff@TopGearSolutions

You'd need to have a bung welded on.

Or if you order a new charge pipe from ER, they can weld you as many bungs as you want with a custom pipe.

The spacing is OK, I ran 2 bung with the same pipe. M5 and M7 specifically. The car was much more responsive with the 2 meth bung 5 and 7 VS M12 and M14 I was using previously.

Thanks Jeff,if the spacing is ok I'll leave it.ill order some injectors.
Does it matter how it's plumbed?i thought about from the solenoid using a Y so it evenly sends meth to both.Or is a tee fine?is there a preference?im thinking less restriction the better but not sure if it implys to meth.

[Torgus]

it's probably easier to sell your CP and buy the BMS cp with the meth nozzle location directly across from each other which is how it should be.

[kboss335]

BMS sells a silicone charge pipe elbow that has a meth bung in it, way cheaper than buying a new cp

[Mike@N54Tuning.com]

Originally Posted by BOosted 335i

I have my er chargepipe with 2 meth bungs I'd say little close to each other.they are 1-1/2 inches on center apart.i want to run a cm10 & cm05 setup.right now I have a cm14 single.its been fine and logs are fine but don't want to chance it.do they sell a kit where I can drill a hole in chargepipe,add a bung style to fit or do I have to get it welded on? Unless the spacing is ok then I'll leave it.looking for opinions thanks.

Have you thought of putting a bung on the lower charge pipe?

Mike

[BOosted 335i]

Originally Posted by kboss335

BMS sells a silicone charge pipe elbow that has a meth bung in it, way cheaper than buying a new cp

i have the ER n55 chargepipe so i couldnt do that

[Torgus]

Originally Posted by kboss335

BMS sells a silicone charge pipe elbow that has a meth bung in it, way cheaper than buying a new cp

true, but he could probably sell his cp and buy the bms one for the same cost of buying the elbow at the end of the day, that was my point. But the elbow is a good choice. I'm in the same boat. buy the bms for the two nozzles or keep my cpe cp and buy the elbow. my understanding is you want to lines to be the exact same length which makes it hard if you use the elbow no? You would end up with a large line which just loops around for no reason other than your other meth bung is 1.5' away.

[BOosted 335i]

Originally Posted by Mike@N54Tuning.com

Have you thought of putting a bung on the lower charge pipe?

Mike

Yes i have.Thinking for now ill run with both bungs.its got to be better then one cm14 firehose as oppose to to a cm10 & cm05 1-1/2 apart.Then later ill install a bung lower 180 degrees from the other.

[Mike@N54Tuning.com]

Originally Posted by BOosted 335i

Yes i have.Thinking for now ill run with both bungs.its got to be better then one cm14 firehose as oppose to to a cm10 & cm05 1-1/2 apart.Then later ill install a bung lower 180 degrees from the other.

Sounds like a good plan.

Mike

[BOosted 335i]

Originally Posted by Torgus

true, but he could probably sell his cp and buy the bms one for the same cost of buying the elbow at the end of the day, that was my point. But the elbow is a good choice. I'm in the same boat. buy the bms for the two nozzles or keep my cpe cp and buy the elbow. my understanding is you want to lines to be the exact same length which makes it hard if you use the elbow no? You would end up with a large line which just loops around for no reason other than your other meth bung is 1.5' away.

i just checked bms & he has a dual bung CP but with diverter valve setup.No blowoff valve.im interested in a long version n55 with 2 bungs which i dont here there.

[Jeff@TopGearSolutions]

Originally Posted by BOosted 335i

Thanks Jeff,if the spacing is ok I'll leave it.ill order some injectors.
Does it matter how it's plumbed?i thought about from the solenoid using a Y so it evenly sends meth to both.Or is a tee fine?is there a preference?im thinking less restriction the better but not sure if it implys to meth.

Solenoid to the Y. Keep the solenoid close to the Y and nozzles.