[nachumk]

Hi,

I have a 2011 (March 2010 build) 335d. I just attempted to use WinKFP to program TELE15. Around 70% through flashing it popped up with an error. It is also running the wiper blades and the car blinks but won't turn on.
The error is:
Error 211:
Error on flash programming!
2089 PABD switching programming mode failed 10FLASH,DIAGNOSE_MODE (ECUPM): ERROR_ECU_SECURITY_ACCESS_DENIED__SECURITY_ACCESS_ REQUESTED
7054 PABD clear flash done - no answer from ECU (IFH-0009) but gateway o.k., no OPPS/Most 10FLASH,FLASH_SCHREIBEN (...): IFH-0009 No response from controlunit
7054 Error clear flash done - no answer from ECU (IFH-0009) but gateway o.k., no OPPS/Most SG_PROGRAMMIEREN
7054 Error clear flash done - no answer from ECU (IFH-0009) but gateway o.k., no OPPS/Most

Please help! I can't get my car to turn on now... Lucky it's a long weekend...

In addition, how can I tell which units need updating?

Nachum

[808AWD325xi]

Did you use an ICOM interface?

[nachumk]

I'm not sure what that is. I purchased the KDCAN cable from one-stop-electronics for $100.

[808AWD325xi]

Modules on the MOST bus should be reprogrammed with an ICOM interface and not a K+DCAN cable.

[nachumk]

Hi,

So I need to purchase a new cable? Can you recommend one? Also, should I be able to recover the module and get my car working again? Or would I need to buy a new control unit?

Thanks,
Nachum

[808AWD325xi]

You should be able to successfully reprogram it with ISTA/P and an ICOM interface.

I can't recommend one personally, there are a lot of Chinese clones out there.

One member reported that this one worked for him recently:
http://www.amazon.com/AUTOS-FAMILY-V.../dp/B00S3A9IA2

Your mileage may vary.

That module shouldn't prevent the car from starting.

[nachumk]

I will look into purchasing an ICOM or finding someone to help me with fixing the module. Thanks!
BTW, the car doesn't start. All it does it flash lights a bit. Engine doesn't even try to start. I have unplugged the negative terminal of the battery and waiting a few minutes. Didn't help. I am trying that again for longer. Any suggestions?
Nachum

[808AWD325xi]

Perhaps the battery needs to be charged.

[nachumk]

Thank you!! That was it. Car is running again albeit without Bluetooth.

I learned some new stuff today. I really appreciate your help.

Nachum

[nachumk]

Using the ICOM interface - would I still need a battery charger to maintain 70A through charging? I saw someone recommend the INC-700A.
Also, do you know how I can find out which modules need updating? I can't quite figure that out.
Thanks again,
Nachum

[808AWD325xi]

Originally Posted by nachumk

Using the ICOM interface - would I still need a battery charger to maintain 70A through charging? I saw someone recommend the INC-700A.
Also, do you know how I can find out which modules need updating? I can't quite figure that out.
Thanks again,
Nachum

Yes, you will. I own a Schumacher INC-700A and highly recommend it.

I also recommend following BMW's guidelines during coding, diagnostics, and/or flash reprogramming:


If you load the latest SP daten, WinKFP in comfort mode will always recommend the latest ZB number for a given module.

[nachumk]

For ECU TELE15, I have 9231090. There is also 9231091. Are those the flash versions? It's pretty unclear to me if those numbers indicate a hardware variation or the flash versions.
If they're hardware variations, then where do I see the flash version that will be burned and the flash version that is currently on the ECU?
Thanks

[808AWD325xi]

Originally Posted by nachumk

For ECU TELE15, I have 9231090. There is also 9231091. Are those the flash versions? It's pretty unclear to me if those numbers indicate a hardware variation or the flash versions.
If they're hardware variations, then where do I see the flash version that will be burned and the flash version that is currently on the ECU?
Thanks

Those are ZB numbers...examine the TELE15.DAT file...

To see which ZB number is currently flashed, see question #7 of my FAQ:
http://www.e90post.com/forums/showpo...48&postcount=2

To learn more about WinKFP...

The manual is located in C:\EC-APPS\NFS\DOKU.