Alternate ground for the Procede?

timtech · 09-25-2007, 06:58 PM

Has anyone found an alternate place to ground the Procede that makes a good solid connection?

I was hoping someone has done this by now since shops know to look for the wire going to the normal ground block.

Kbueno · 09-25-2007, 11:35 PM

+1
I have a thread in the Vishnu forum on this as well.
Can someone post a pic on a workable ground in the ECU box?

Dascamel · 09-26-2007, 01:38 AM

Doesn't the ECU need to have a ground wire also?

sflgator · 09-26-2007, 11:39 AM

There's a torx screw inside the back of the ECU box, but it's difficult to get to (I think), and obviously, you need a torx wrench. Does anyone know if this would work?

HyperM3 · 09-26-2007, 12:19 PM

I used the screw below the plastic box cover. The one where the whole plastic engine bay piece is held on by two 8mm nuts. I slid it below the clip for that. Now its covered and going around the box instead of outside of it.

sflgator · 09-26-2007, 12:29 PM

Quote:

Originally Posted by HyperM3

I used the screw below the plastic box cover. The one where the whole plastic engine bay piece is held on by two 8mm nuts. I slid it below the clip for that. Now its covered and going around the box instead of outside of it.

Not sure which one you're talking about.

Would you mind taking a quick pic of that?

HyperM3 · 09-26-2007, 12:37 PM

Quote:

Originally Posted by sflgator

Not sure which one you're talking about.

Would you mind taking a quick pic of that?

Sorry for the poor quality, just ran out and took pics with my phone.

OpenFlash · 09-26-2007, 12:39 PM

Quote:

Originally Posted by sflgator

There's a torx screw inside the back of the ECU box, but it's difficult to get to (I think), and obviously, you need a torx screwdriver. Does anyone know if this would work?

Yep, it will work

Shiv

sflgator · 09-26-2007, 12:43 PM

Quote:

Originally Posted by HyperM3

Sorry for the poor quality, just ran out and took pics with my phone.

Thanks, man.

That's definitely a better solution, since it's covered. For the wire to be fully inside the box though, I guess you could attach it to that torx screw inside the ECU box...anyone have a torx wrench?

HyperM3 · 09-26-2007, 12:44 PM

Quote:

Originally Posted by sflgator

Thanks, man.

That's definitely a better solution, since it's covered. For the wire to be fully inside the box though, I guess you could attached it to that torx screw inside the ECU box...anyone have a torx wrench?

I looked at that solution but after scraping my hands up on the box trying to remove the pieces to get to it, I gave up.

Kbueno · 09-26-2007, 04:08 PM

Quote:

Originally Posted by HyperM3

Sorry for the poor quality, just ran out and took pics with my phone.

Hey, thank-you. I'll give it a shot when V2 arrives.

sflgator · 09-26-2007, 07:47 PM

Quote:

Originally Posted by 335lvr

Hey, thank-you. I'll give it a shot when V2 arrives.

+1. Thanks, HyperM3.

CarbonBeast · 12-17-2007, 10:16 PM

Quote:

Originally Posted by HyperM3

Sorry for the poor quality, just ran out and took pics with my phone.

Great Post... Thanks Hyper M3!!

baron · 01-22-2008, 12:17 AM

Quote:

Originally Posted by HyperM3

Sorry for the poor quality, just ran out and took pics with my phone.

I checked the location of that bolt in that picture and it seems to be connected to a plastic piece, not metal. So how could this bolt be connected to ground? Thanks.

HyperM3 · 01-22-2008, 12:22 AM

Quote:

Originally Posted by baron

I checked the location of that bolt in that picture and it seems to be connected to a plastic piece, not metal. So how could this bolt be connected to ground? Thanks.

((sigh)) Kick over a rock sometime instead of just seeing it as a rock on the ground. There might be buried treasure underneath.

baron · 01-22-2008, 01:47 AM

Quote:

Originally Posted by HyperM3

((sigh)) Kick over a rock sometime instead of just seeing it as a rock on the ground. There might be buried treasure underneath.

So that piece is metal underneath? Did someone verify it with a voltmeter? Thanks.

Fubarsky · 01-22-2008, 10:04 AM

Quote:

Originally Posted by shiv@vishnu

Yep, it will work

Shiv

I did not get a good continuity to ground on these torx screws. I am looking for something under the dash when I run the USB thru the firewall.

09-25-2007, 06:58 PM	#1
timtech Lieutenant 25 Rep 518 Posts Drives: M3 Join Date: May 2007 Location: Over there iTrader: (7)	Alternate ground for the Procede? Has anyone found an alternate place to ground the Procede that makes a good solid connection? I was hoping someone has done this by now since shops know to look for the wire going to the normal ground block.
	Appreciate 0 Tweet Quote

09-25-2007, 11:35 PM	#2
Kbueno Lieutenant Colonel 101 Rep 1,712 Posts Drives: F82 Join Date: Jan 2007 Location: California iTrader: (5)	+1 I have a thread in the Vishnu forum on this as well. Can someone post a pic on a workable ground in the ECU box?
	Appreciate 0 Quote

09-26-2007, 01:38 AM	#3
Dascamel Lieutenant Colonel 50 Rep 1,664 Posts Drives: 2008 e92 M3, 2010 e91 328i Join Date: Jul 2007 Location: Bakersfield, CA iTrader: (0)	Doesn't the ECU need to have a ground wire also? __________________ 2008 E92 M3 Jerez Black,DCT,Fox Red ext,Prem,Tech,19", ipod/usb, CF roof and trim 2010 E91 328i Space Gray,Black int, M sport, most options 2007 Montego Blue 335i (retired)
	Appreciate 0 Quote

09-26-2007, 11:39 AM	#4
sflgator Major General 166 Rep 5,389 Posts Drives: '09 MB C63 AMG & '08 MB GL450 Join Date: Oct 2006 Location: U.S. iTrader: (1)	There's a torx screw inside the back of the ECU box, but it's difficult to get to (I think), and obviously, you need a torx wrench. Does anyone know if this would work? __________________ \|2009 RENNtech MB C63 AMG \| Black/Black Leather/Black Maple \| Premium II \| MultiMedia \| iPod \| \| TeleAid \| Charcoal Filter Delete \| BMC High-Flow Air Filters \| High-Flow Secondary Cats \| Clear Side Markers \| Last edited by sflgator; 09-26-2007 at 12:44 PM..
	Appreciate 0 Quote

09-26-2007, 12:19 PM	#5
HyperM3 Too many Alex's, from now on, call me Beaufort 359 Rep 6,188 Posts Drives: See Sig Join Date: Feb 2007 Location: Lawrenceville, NJ iTrader: (8)	I used the screw below the plastic box cover. The one where the whole plastic engine bay piece is held on by two 8mm nuts. I slid it below the clip for that. Now its covered and going around the box instead of outside of it. __________________ 13 HD FatBob 17 A4 Glacier/Black 1st Edition/Pre+/Sport/EurocodeTMD/Racechip 16 S6 (gone),14 S6 (gone),14 S6 (gone),13 S6 (gone),10 S4 (gone) 07 335i(gone)
	Appreciate 0 Quote

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search