[SoFlo335]

Got the car on the dyno today. Unfortunately, since it was a dyno day, there where too many people, and they could not get tq readings for my car :/. They told me that it was going to take too long to get the tq settings hooked up.... I dont have any stock dyno sheets, but I have a feeling that this could be a little higher than average (~270rw). This was a dynojet BTW.

Mods:
JB1H
Solenoid kit
Duel intakes

Temp: 95.82 degrees F and Humidity was 39%

We did two runs, got them both on video, although they are not great. 1st run was in 3rd gear and made 325.96whp and the second run was in 4th gear and made 325.76whp (the car actually hit 150mph). I will post up the video tomorrow of the two runs.

Conclusion:
I am very happy with the results. I was definitely not expecting anything greater than 310whp. Im a little mad that I was not able to get any tq readings, but next time I go, Ill make sure to do it. Also, I was surprised that the car was able to hit 150mph in 4th gear with ease, granted, there is no wind resistance. Just wanted to add that with the two runs that I did, it shows the JB is very consistent, being less than a HP off the 1st run.

[Amir87]

Nice power gain with the JB1!

[e90AW335i]

Very nice but I don't understand why they couldn't get the torque. I am assuming they were saying they couldn't take the two bolts out of the engine cover and clamp the wire for RPMs. Purely lazy and unprofessional IMO. I wouldn't have paid for essentially HALF a dynosheet.

How much did you pay?

[RedGT3]

29.2?

[SoFlo335]

Originally Posted by e90AW335i

Very nice but I don't understand why they couldn't get the torque. I am assuming they were saying they couldn't take the two bolts out of the engine cover and clamp the wire for RPMs. Purely lazy and unprofessional IMO. I wouldn't have paid for essentially HALF a dynosheet.

How much did you pay?

45$ for the two runs and A/F

Apparently it takes "45min" to hook up for tq readings....

Originally Posted by fll335

29.2?

Dont think so. Just had the car serviced the past week and I looked at the receipts and couldnt find anything about having the car updated, so Im gonna say Im pre-29.2.

[RiXst3r]

Nice numbers! Congrats!!!

-Rick

[scalbert]

Originally Posted by SoFlo335

Apparently it takes "45min" to hook up for tq readings....

No, it was a Dynojet and takes less than five minutes to get the RPM hook up which, in turn, provides torque readings.

[SoFlo335]

Originally Posted by scalbert

No, it was a Dynojet and takes less than five minutes to get the RPM hook up which, in turn, provides torque readings.

Yea, well, thats what I was told :/. Not trying to argue with you, just saying what the guy told me. Ill make sure to get tq readings next time (hopefully with JB3).

[RiXst3r]

Originally Posted by SoFlo335

Yea, well, thats what I was told :/. Not trying to argue with you, just saying what the guy told me. Ill make sure to get tq readings next time (hopefully with JB3).

take this with you...

http://www.n54tech.com/forums/showthread.php?t=488

[scalbert]

Originally Posted by RiXst3r

take this with you...

http://www.n54tech.com/forums/showthread.php?t=488

Exactly.

[SoFlo335]

Originally Posted by RiXst3r

take this with you...

http://www.n54tech.com/forums/showthread.php?t=488

Perfect! Its a shame that I didnt read that before hand though. But no worries, Ill have that next time I go!

[e90AW335i]

Originally Posted by SoFlo335

45$ for the two runs and A/F

Apparently it takes "45min" to hook up for tq readings....

Do me a favor and do this to that guy

I wouldn't have let them within 15ft of my car if they think the RPM reading takes 45min to hook up.

Oh well, congrats on the HP number at least.....

[SoFlo335]

Thanks for the comment guys! Im really stoked about the outcome, and again, I wish I was able to get the tq readings