E90Post
 


 
BMW 3-Series (E90 E92) Forum > E90 / E92 / E93 3-series Powertrain and Drivetrain Discussions > NA Engine (non-turbo) / Drivetrain / Exhaust Modifications > N52 - compatible ZF auto transmissions



Reply
 
Thread Tools Search this Thread
      08-03-2024, 06:31 PM   #111
siado
New Member
5
Rep
15
Posts

Drives: 128
Join Date: Mar 2024
Location: Earf

iTrader: (0)

Looks like the flywheel may be the culprit for me. The 128 flywheel 11227548102 has a flex plate that protrudes quite a bit in comparison to the 2011 528 (N52/8HP45) flywheel.

128


528
Appreciate 0
      08-08-2024, 08:08 PM   #112
pp2
Registered
0
Rep
1
Posts

Drives: BMW 330d e92
Join Date: Mar 2024
Location: Skopje, North Macedonia

iTrader: (0)

Quote:
Originally Posted by cheerio View Post
Great to see someone giving it a go!
I think you might be better off using E84 coding/firmware instead of E70; the E70 seems to be set up differently to the E89 family.

Flash an E84 ZB to the EGS. IIRC, when I tried this it seemed to work aside from a DSC code. You shouldn't have to mess around with a E70 CAS. Use a JBBFE 3 from a late E90 or perhaps an E84. E84 electronic shifter should work once wired up.

Thanks for being the guinea pig and testing this out, I'm keen to hear how it goes.
Hey,

Do you happen to remember what the DSC code was?
As I can find online regarding this problem, seems like it would be hard to solve since the DSC units are older in e90s. In the xDrive models, when the 8hp transmission goes into 8th gear, the DSC throws an error and goes into emergency mode (8 can't be represented with 3bits???).
How did you plan to proceed to solve this?
Did you only use the Yanhua for programming and NcsExpert for coding?
This thread is as close as it gets to a full OEM 8hp in e90 solution, so I think it's worth asking

Cheers
Appreciate 0
      08-11-2024, 10:21 AM   #113
raphiilouu
Registered
0
Rep
2
Posts

Drives: 330xi E91
Join Date: Jul 2024
Location: France

iTrader: (0)

Quote:
Originally Posted by siado View Post
I am in the middle of this currently with an E82 128i and 8HP45 from a 2011 535.

I gave it a shot with the N55 torque converter today and it looked like the bell housing didn't want to seat fully. The N55 converter is a bit longer than the 6L45 N52 converter and has different spline pattern. I'm thinking I'll try an N20 converter and see how it goes.

I have the Seems Legit driveshaft for the M3 DCT swap and CANTCU with an F82 M4 shifter, so the transmission cross bracket and torque converter are the last bits to figure out.

RealOEM shows the E89 z4 sdrive 28i had the 8HP45 and used the same rear mount bracket as the 128i. https://www.realoem.com/bmw/enUS/sho...diagId=22_0106

Didn't realize this until I got home today or would have attempted to bolt it up in the car. Can't get back to it until Tuesday, but will report back.
Thanks for the answer

I’ve been looking for some more infos but I can’t find any.

The n20 converter mounting is different with the flex plate not being flat, and that may cause an issue apparently with the n52 flywheel.

I’d like to give it a shot however as that’s a daily driven I can’t screw it up, hence the reason I look up EVERYTHING to make sure I have no bad surprises under the car.

For now, I’ve seen that the transmission mounts are compatible, the ATC 300 looks compatible with the 8hp45x awd version (not 100% sure though) and the CANTCU offers a full compatibility.
The only thing I have to figure out is which TC should I get and how to make it work.
Appreciate 0
      10-31-2024, 12:09 PM   #114
weste46
Registered
0
Rep
2
Posts

Drives: BMW 330ci
Join Date: Sep 2023
Location: Indiana

iTrader: (0)

Thumbs up

Quote:
Originally Posted by siado View Post
Looks like the flywheel may be the culprit for me. The 128 flywheel 11227548102 has a flex plate that protrudes quite a bit in comparison to the 2011 528 (N52/8HP45) flywheel.

128


528
Keep us updated on your progress, it would be really cool to see a 128i with an 8HP!
Appreciate 0
      11-03-2024, 12:14 PM   #115
sunnyjay
New Member
10
Rep
15
Posts

Drives: 2008 335i
Join Date: Jun 2018
Location: CA

iTrader: (0)

In for updates. Can't wait to see the progress on this.
Appreciate 0
Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 01:41 PM.




e90post
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST