Anyone in the West LA area who can help with JB+ installation?

james.335i · 07-14-2009, 12:55 PM

Anyone in the West LA area who can help with JB+ installation?
I am a noob as far as it goes with opening up the hood and messing around with things in the engine, I would be willing to pay if someone could help me install... also, if someone had a Bavarian Tech Scanner that I might be able to utilize in the area from time to time as needed - that would also be amazingly helpful.

Thanks!

Aurora Bearialis · 07-14-2009, 01:01 PM

Quote:

Originally Posted by james.335i

Anyone in the West LA area who can help with JB+ installation?
I am a noob as far as it goes with opening up the hood and messing around with things in the engine, I would be willing to pay if someone could help me install... also, if someone had a Bavarian Tech Scanner that I might be able to utilize in the area from time to time as needed - that would also be amazingly helpful.

Thanks!

I just put my JB3 in this past weekend. Took an hour and a half. Just take your time and read the directions and it should go swimmingly.

bimmerlex · 07-14-2009, 01:22 PM

JB+ you said? It's the same install as Turbo Tuner. Very easy. I can help if you still haven't done it.

Aurora Bearialis · 07-14-2009, 01:28 PM

Quote:

Originally Posted by bimmerlex

JB+ you said? It's the same install as Turbo Tuner. Very easy. I can help if you still haven't done it.

Oh sorry dude, JB+. Yeah thats a sinch

5 minute job. You can do it, I suggest instead of using a flathead screwdriver to take out the existing wire, use a penny instead cos it will allow you put the penny in between the clips and pull out the wire, without dropping the penny. I just found it easier cos I couldn't do it with a small flathead.

james.335i · 07-14-2009, 01:48 PM

Quote:

Originally Posted by Aurora Bearialis

Oh sorry dude, JB+. Yeah thats a sinch

5 minute job. You can do it, I suggest instead of using a flathead screwdriver to take out the existing wire, use a penny instead cos it will allow you put the penny in between the clips and pull out the wire, without dropping the penny. I just found it easier cos I couldn't do it with a small flathead.

hmmm... OK... I will try it.

I wanted to do the install without removing the air-filter, but I guess this will just be harder in the end?

bimmerlex · 07-14-2009, 02:03 PM

Quote:

Originally Posted by james.335i

hmmm... OK... I will try it.

I wanted to do the install without removing the air-filter, but I guess this will just be harder in the end?

In e90/92 you don't have to remove the filter. There is enough space to get in from the side.

james.335i · 07-14-2009, 02:03 PM

Quote:

Originally Posted by bimmerlex

In e90/92 you don't have to remove the filter. There is enough space to get in from the side.

Excellent.

dailo · 07-14-2009, 03:42 PM

USB cord works very well also.

james.335i · 07-14-2009, 09:52 PM

Quote:

Originally Posted by dailo

USB cord works very well also.

Yeah, I wish someone would do like a video or something and upload to youtube but apparently it is so easy so nobody wants to take the time to do it... not even Burger Motorsports...

FrankiE90 · 07-14-2009, 11:24 PM

pm mote.

mJ335 · 07-15-2009, 12:30 AM

If you come to OC, I'll do it for you for free! It only takes 1 minute for me.

PM me if you're down here.

PaulBailey@ltbmw · 07-15-2009, 12:38 AM

Quote:

Originally Posted by FrankiE90

pm mote.

+1

james.335i · 07-15-2009, 12:41 AM

Quote:

Originally Posted by mJ335

If you come to OC, I'll do it for you for free! It only takes 1 minute for me.

PM me if you're down here.

OK, I'll keep that in mind. I appreciate the offer regardless!

FrankiE90 · 07-15-2009, 02:19 AM

Quote:

Originally Posted by mJ335

If you come to OC, I'll do it for you for free! It only takes 1 minute for me.

PM me if you're down here.

i want to see this on youtube.
no edits on the video, one min take on the vid.

james.335i · 07-15-2009, 12:50 PM

Quote:

Originally Posted by FrankiE90

i want to see this on youtube.
no edits on the video, one min take on the vid.

This would be amazing, if anyone could do this it would be greatly appreciated! I am sure many people would benefit from this, not to mention the huge number of sales Burger Motorsports will make if they just make their installation instructions more accessible in video form to their less mechanically inclined power hungry 335i drivers...

RambleJ · 07-15-2009, 01:44 PM

I used to be able to do one minute installs.. But that was after I broke the clip off my TMAP sensor..

I was able to do this with my bare hands.. No usb cable or guitar pick, just a little lifting pressure with the fingertip and a pull from the other arm and boom..

james.335i · 07-15-2009, 03:09 PM

Quote:

Originally Posted by RambleJ

I used to be able to do one minute installs.. But that was after I broke the clip off my TMAP sensor..

I was able to do this with my bare hands.. No usb cable or guitar pick, just a little lifting pressure with the fingertip and a pull from the other arm and boom..

EXACTLY.. i am so afraid i am going to break my TMAP sensor ... if i do break it then isn't that a tell-tale sign that modifications have been performed?

dailo · 07-15-2009, 04:35 PM

Quote:

Originally Posted by james.335i

Yeah, I wish someone would do like a video or something and upload to youtube but apparently it is so easy so nobody wants to take the time to do it... not even Burger Motorsports...

It's kind of hard to make a video as you can't really get a camera in there. The space is very small and you're doing it blind. When I do it I just make sure that the chip or slot from the end of the usb cable if facing up so that the opening is the part that catches the clip. Once the usb cord gets onto the clip just slide it up until it doesn't move anymore and you should be able to pull out the cable.

Kroy · 07-15-2009, 09:18 PM

How much is a replacement clip? Is the clip replaceable? I'm at work and haven't looked under my hood yet.

mJ335 · 07-16-2009, 07:25 AM

Quote:

Originally Posted by FrankiE90

i want to see this on youtube.
no edits on the video, one min take on the vid.

LMAO give me a dime and I'll show you the magic

james.335i · 07-17-2009, 02:39 AM

Quote:

Originally Posted by mJ335

LMAO give me a dime and I'll show you the magic

It seems that the average individual not only couldn't do it in under 5 minutes and might even break the TMAP sensor if one happens to lack knowledge of the intricacies of the engine bay ... thus -- in order to maximize sales and appeal to a greater amount of customers, create a video that explains how to do this fabled 1 minute installation... there must be some way to get that area illuminated and a way to have an instruction video done, as it is now it is just plain confusing to novice individual interested in a simple tune for moderate HP gains.

07-14-2009, 12:55 PM	#1
james.335i New Member 2 Rep 28 Posts Drives: 335i Coupe 2007 - E92 Join Date: Jul 2009 Location: Beverly Hills iTrader: (0)	Anyone in the West LA area who can help with JB+ installation? Anyone in the West LA area who can help with JB+ installation? I am a noob as far as it goes with opening up the hood and messing around with things in the engine, I would be willing to pay if someone could help me install... also, if someone had a Bavarian Tech Scanner that I might be able to utilize in the area from time to time as needed - that would also be amazingly helpful. Thanks!
	Appreciate 0 Tweet Quote

07-14-2009, 01:22 PM	#3
bimmerlex Captain 85 Rep 895 Posts Drives: 2024 BMW X4M Competition Join Date: Jan 2007 Location: SoCal. iTrader: (25) Garage List 2025 BMW X5 40i M-S ... [9.75] 2024 BMW X4M Compet ... [0.00]	JB+ you said? It's the same install as Turbo Tuner. Very easy. I can help if you still haven't done it. __________________ 2025 BMW X5 Xdrive40i M-Sport M-Performance 2024 BMW X4M Competition 2025 BMW M340i xDrive M-Sport M-Performance
	Appreciate 0 Quote

07-14-2009, 03:42 PM	#8
dailo Private 1 Rep 83 Posts Drives: E92 Join Date: Apr 2008 Location: Bay Area iTrader: (2)	USB cord works very well also.
	Appreciate 0 Quote

07-14-2009, 11:24 PM	#10
FrankiE90 Major General 678 Rep 8,800 Posts Drives: Krooked Sk8board Join Date: Feb 2008 Location: Pasadena, Ca iTrader: (11)	pm mote. __________________ FrankiE90 AKA:.[The TANK] *CLICK THE SIG E90s (been gone but not forgotten) • KW clubsports • • • • • • • • • • 18" BBS GT4 // Build E30 (pending) + E46 M3 Wagon ESTORIL Blue
	Appreciate 0 Quote

07-15-2009, 12:30 AM	#11
mJ335 Amateur Post Whore 139 Rep 3,035 Posts Drives: 07 E90 SparkLiN G. 335i Join Date: Sep 2007 Location: SocaL iTrader: (17) Garage List 2007 e90 335i [0.00]	If you come to OC, I'll do it for you for free! It only takes 1 minute for me. PM me if you're down here. __________________ Go WiTh ThE FLoW. \|BL\|RS\|PIAA\|CFE\|CFMC\|SSM\|CFG\|CFDP\|ABG\|M6\|AFE\|MTECH \|RPI\|JB+\|CSLT\|KWSC\|
	Appreciate 0 Quote

07-15-2009, 01:44 PM	#16
RambleJ Colonel 60 Rep 2,014 Posts Drives: F10 535i M-sport Join Date: Oct 2008 Location: Back in teh so cal iTrader: (2)	I used to be able to do one minute installs.. But that was after I broke the clip off my TMAP sensor.. I was able to do this with my bare hands.. No usb cable or guitar pick, just a little lifting pressure with the fingertip and a pull from the other arm and boom..
	Appreciate 0 Quote

07-15-2009, 09:18 PM	#19
Kroy Brigadier General 184 Rep 3,032 Posts Drives: E90 Join Date: Jul 2009 Location: Los Angeles, CA iTrader: (1)	How much is a replacement clip? Is the clip replaceable? I'm at work and haven't looked under my hood yet.
	Appreciate 0 Quote

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search