procede v5!!! problem of OBD rewrite of BMW dealer

skyintothesea · 03-01-2011, 12:30 PM

My car is 2011 e92 335, with procede V5 installed. Warranty to next year.

Last weekend, I went to BMW dealer for a four-wheel-positioning, due to I don't know after this positioning dealer need to rewrite this program to ECU via OBD (previous I dismantled V5 before go in BMW dealer), then dealer read all data from ECU, but they can't rewrite this program via OBD, there was display" ERROR OF CANBUS"

I was afraid that dealer will check our engine/canbus system, so I made a pretence of dinner and go away.

Is anybody meet this problem?

NiVeDh · 03-01-2011, 12:31 PM

Did you put the Procede in valet mode?

skyintothesea · 03-01-2011, 12:32 PM

procede V5 is good product, I just wanna to know when dismantle this for safety of warranty.

skyintothesea · 03-01-2011, 12:34 PM

Quote:

Originally Posted by NiVeDh

Did you put the Procede in valet mode?

Yes, valet mode of course.

PKumarM3 · 03-01-2011, 12:37 PM

Quote:

Originally Posted by skyintothesea

procede V5 is good product, I just wanna to know when dismantle this for safety of warranty.

assuming you should remove the V5 whenever you bring your car in to a BMW dealership.

stressdoc · 03-01-2011, 12:39 PM

Always take it out if there is any chance of an OBD hookup. You do not want the prying eyes of ISTA to look into your ECU.

skyintothesea · 03-01-2011, 12:45 PM

Quote:

Originally Posted by PKumarM3

assuming you should remove the V5 whenever you bring your car in to a BMW dealership.

thanks, I think so

skyintothesea · 03-01-2011, 12:47 PM

Quote:

Originally Posted by stressdoc

Always take it out if there is any chance of an OBD hookup. You do not want the prying eyes of ISTA to look into your ECU.

except car washing only. thanks

TheAcAvenger · 03-01-2011, 02:39 PM

I just had a software update with V5 and did nothing but turned canclear off. Apparently you don't even have to do that anymore, but they updated my car on the first try

Sniz · 03-01-2011, 02:43 PM

Quote:

Originally Posted by skyintothesea

except car washing only. thanks

unless the wash boys are a lot different than they are here Id suggest staying away from the dealership for washes at all costs.

I used to be one when I was 16, things got ugly. Wash mitts left on the ground then reused on new cars etc.

wash it yourself or have a professional do it.

fisherbln · 03-01-2011, 03:34 PM

Quote:

Originally Posted by Sniz

unless the wash boys are a lot different than they are here Id suggest staying away from the dealership for washes at all costs.

I used to be one when I was 16, things got ugly. Wash mitts left on the ground then reused on new cars etc.

wash it yourself or have a professional do it.

+1. Dealers will trash your paint when they attempt to wash it.

lndnny · 03-01-2011, 03:39 PM

I thought the N55 versions of the Procede V5 still had an issue with CAN-communication and had to be fully removed to allow dealer reprograms

?

fisherbln · 03-01-2011, 03:43 PM

Quote:

Originally Posted by lndnny

I thought the N55 versions of the Procede V5 still had an issue with CAN-communication and had to be fully removed to allow dealer reprograms

?

You are correct. Above posters were referring to the N54 version which doesn't have any issue.

shockin330i · 03-01-2011, 03:44 PM

hhmm, I wonder if you can just disconnect the 2 canbus wires and leave everything else in tact...

OpenFlash · 03-02-2011, 01:16 AM

For the n55, just disconnect the 2 CAN wire taps in the ecu box. This will bypass the CAN functions that are interfering with the DME programming. Or better yet, unplug the whole Procede when taking it in to the dealership.

The n54 is different in the CAN functions are disabled when the car isn't running. Whereas in the n55, they are always functional. This is because we use it to read applied throttle which is necessary to do a throttle pump code clear (when the engine is running). Soon, we'll probably eliminate that feature since it can be done through the command center.

shockin330i · 03-02-2011, 01:23 AM

Quote:

Originally Posted by shiv@vishnu

For the n55, just disconnect the 2 CAN wire taps in the ecu box. This will bypass the CAN functions that are interfering with the DME programming. Or better yet, unplug the whole Procede when taking it in to the dealership.

The n54 is different in the CAN functions are disabled when the car isn't running. Whereas in the n55, they are always functional. This is because we use it to read applied throttle which is necessary to do a throttle pump code clear (when the engine is running). Soon, we'll probably eliminate that feature since it can be done through the command center.

Good to hear. I don't feel like messing with the crank sensor again

Amlethae · 03-02-2011, 09:49 AM

[By now this should be expected from me:]

This is the same issue that causes the N55 Procede V5 to prevent us from coding the vehicle ourselves. Shiv totally understands whats going on and he will be fixing it in the next update.

03-01-2011, 12:30 PM	#1
skyintothesea Enlisted Member 7 Rep 39 Posts Drives: 2011 e92 coupe 335i DCT Join Date: Dec 2010 Location: China iTrader: (0)	procede v5!!! problem of OBD rewrite of BMW dealer My car is 2011 e92 335, with procede V5 installed. Warranty to next year. Last weekend, I went to BMW dealer for a four-wheel-positioning, due to I don't know after this positioning dealer need to rewrite this program to ECU via OBD (previous I dismantled V5 before go in BMW dealer), then dealer read all data from ECU, but they can't rewrite this program via OBD, there was display" ERROR OF CANBUS" I was afraid that dealer will check our engine/canbus system, so I made a pretence of dinner and go away. Is anybody meet this problem?
	Appreciate 0 Tweet Quote

03-01-2011, 12:31 PM	#2
NiVeDh Major General 426 Rep 8,003 Posts Drives: '08 E90 335i, '99 E36 M3 Join Date: Apr 2009 Location: Houston, TX & Atlanta, GA iTrader: (132) Garage List 2008 BMW 335i Sedan [8.66]	Did you put the Procede in valet mode?
	Appreciate 0 Quote

03-01-2011, 12:32 PM	#3
skyintothesea Enlisted Member 7 Rep 39 Posts Drives: 2011 e92 coupe 335i DCT Join Date: Dec 2010 Location: China iTrader: (0)	procede V5 is good product, I just wanna to know when dismantle this for safety of warranty.
	Appreciate 0 Quote

03-01-2011, 12:39 PM	#6
stressdoc Moderator 657 Rep 10,863 Posts Drives: BMW i8; Toy 4runner TRD pro Join Date: Jun 2005 Location: Waco TX iTrader: (0)	Always take it out if there is any chance of an OBD hookup. You do not want the prying eyes of ISTA to look into your ECU. __________________ My recent ED photos: http://f80.bimmerpost.com/forums/sho....php?t=1026808 my not-so-recent ED: http://www.e90post.com/forums/showthread.php?t=31829 Please join BMWCCA http://bmwcca.org/index.php?pageid=c...&ref_by=300279
	Appreciate 0 Quote

03-01-2011, 02:39 PM	#9
TheAcAvenger Brigadier General 137 Rep 3,132 Posts Drives: 2018 R35 GTR / 2007 E92 335i Join Date: Apr 2006 Location: 757 > Nova > Denver iTrader: (1)	I just had a software update with V5 and did nothing but turned canclear off. Apparently you don't even have to do that anymore, but they updated my car on the first try __________________ 2018 R35 GT-R Cicio800 \| 2007 E92 335i - RB Turbos, TC Kline DA Coils, HPA M3 Suspension, Quaife LSD, Stoptech BBK, JB4, FuelIT, AR Downpipes, RDSport Quads, Stett OC, Helix IC, Volk TE-37, Vorsteiner V-35, OSS Headlights \| Retired - 2015 F82 M4
	Appreciate 0 Quote

03-01-2011, 03:39 PM	#12
lndnny Lurker... 0 Rep 26 Posts Drives: 2007 Montego Blue 335i Join Date: Jun 2010 Location: Ohio iTrader: (6)	I thought the N55 versions of the Procede V5 still had an issue with CAN-communication and had to be fully removed to allow dealer reprograms ?
	Appreciate 0 Quote

03-01-2011, 03:44 PM	#14
shockin330i Brigadier General 807 Rep 4,784 Posts Drives: 2016 ZCP M3 Join Date: Jan 2007 Location: f y'all, I'm from Texas (RGV) iTrader: (1)	hhmm, I wonder if you can just disconnect the 2 canbus wires and leave everything else in tact... __________________ ERnie 2016 BSM/f80/ZCP
	Appreciate 0 Quote

03-02-2011, 01:16 AM	#15
OpenFlash 1791 Rep 17,960 Posts Drives: A Lot Join Date: Sep 2006 Location: SF Bay, CA iTrader: (0) Garage List 2018 Ducati Panigal ... [0.00] 2016 Mazda CX5 [0.00] 2017 Aprilia Tuono ... [0.00] 2019 BMW M2 Competi ... [0.00] 2015 BMW M5 Competi ... [10.00] 2016 Ducati XDiavel S [0.00] 2016 AMG GT S [0.00] 2011 Ferrari 458 It ... [0.00] 2017 Charger Hellcat [0.00] 2015 KTM Super Duke ... [0.00] 2016 KTM RC390 [0.00]	For the n55, just disconnect the 2 CAN wire taps in the ecu box. This will bypass the CAN functions that are interfering with the DME programming. Or better yet, unplug the whole Procede when taking it in to the dealership. The n54 is different in the CAN functions are disabled when the car isn't running. Whereas in the n55, they are always functional. This is because we use it to read applied throttle which is necessary to do a throttle pump code clear (when the engine is running). Soon, we'll probably eliminate that feature since it can be done through the command center.
	Appreciate 0 Quote

03-02-2011, 09:49 AM	#17
Amlethae Private First Class 14 Rep 169 Posts Drives: 2011 335ix M-Sport Join Date: Oct 2010 Location: Clifton, NJ iTrader: (0) Garage List 2011 335xi [0.00]	[By now this should be expected from me:] This is the same issue that causes the N55 Procede V5 to prevent us from coding the vehicle ourselves. Shiv totally understands whats going on and he will be fixing it in the next update. __________________ *2011 335xi E90 N55 6MT Performance Edition* Other rides: Ducati StreetFighter 848 \| Ducati Monster 696 \| Porsche Spyder 550A (Replica)
	Appreciate 0 Quote

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search