P3Cars - custom molded stealth diagnostic connector

RiXst3r · 04-11-2011, 08:05 PM

We wanted to elegantly and professionally tackle the issue of protruding diagnostic connections, for products like our v2 gauge that use this connector during daily driving.

We designed and had custom molded cables to specifically fit inside and behind the area where the diagnostic connector lives, completely hidden from view.

Although it added significant delays to the release of the new v2 gauge waiting for these cables, our attention to detail could not overlook this important aspect of keeping things looking OEM.

Here are a few photos to show how easy it is to install this connector completely stealth.

Popping it off is easy as well if you need to use the port for something else.

AltecBX · 04-11-2011, 08:11 PM

Very clean look!!

99three · 04-11-2011, 08:35 PM

A proper looking setup. Very OEM looking. That is ultimately a huge selling point for me anyway. I'm looking forward to getting my device in the post. Any ETA when they will be shipping out?

bimmertt · 04-11-2011, 08:42 PM

so for this gauge to work, you just connect it to the OBD port?

Kalud · 04-11-2011, 09:08 PM

Very nice, great work!

vasillalov · 04-11-2011, 11:39 PM

Is this connector going to be included with all gauge purchases?

RiXst3r · 04-12-2011, 03:22 PM

Quote:

Originally Posted by vasillalov

Is this connector going to be included with all gauge purchases?

Yes

only1 · 04-12-2011, 03:43 PM

Quote:

Originally Posted by bimmertt

so for this gauge to work, you just connect it to the OBD port?

Is this correct?

Kalud · 04-12-2011, 03:45 PM

Quote:

Originally Posted by only1

Is this correct?

Yes for n55, n54 you need to install the included boost sensor.

2kaccordocoupe · 04-12-2011, 03:58 PM

Nice

ren · 04-12-2011, 04:08 PM

Quote:

Originally Posted by only1

Is this correct?

It's partially correct. For N54 engines, you need to install an additional boost sensor which is really easy to do. The rest of of the information comes from the DME.

04-11-2011, 08:05 PM	#1
RiXst3r 288 Rep 6,510 Posts Drives: M235i Join Date: Sep 2006 Location: Ohio iTrader: (14)	P3Cars - custom molded stealth diagnostic connector We wanted to elegantly and professionally tackle the issue of protruding diagnostic connections, for products like our v2 gauge that use this connector during daily driving. We designed and had custom molded cables to specifically fit inside and behind the area where the diagnostic connector lives, completely hidden from view. Although it added significant delays to the release of the new v2 gauge waiting for these cables, our attention to detail could not overlook this important aspect of keeping things looking OEM. Here are a few photos to show how easy it is to install this connector completely stealth. Popping it off is easy as well if you need to use the port for something else. Attached Images
	Appreciate 0 Tweet Quote

04-11-2011, 08:11 PM	#2
AltecBX Colonel 341 Rep 2,663 Posts Drives: BMW 335xi Sedan; BMW M3 ZCP Join Date: Nov 2007 Location: NYC iTrader: (0) Garage List 2018 BMW M3 ZCP [0.00] 2007 BMW 335Xi [0.00]	Very clean look!! __________________ 335xi Sedan 6AT \| Weather(70-85°F) \| N54 Tune Comparison Chart \|\| N54 Turbo Upgrade Comparison Chart -PROcede Rev. 2.5 ~ v5 (3/17 maps) / JB4 (8/21 maps) / COBB (Stg2+FMIC LT Aggressive maps) †Procede Map2(UT 45 - IGN 40) Aggression Target 2.0 \| 0-60 in 4.0sec \|\| †Cobb E30 LT (35% Ethanol/65% 93 Octane) \| 0-60 in 3.9sec AR Design Catless DP \| BMS DCI + OCC \| ETS 5 FMIC \| Alpina B3 Trans Flash \|235/265 19" Michelin PSS
	Appreciate 0 Quote

04-11-2011, 08:35 PM	#3
99three Banned 28 Rep 838 Posts Drives: 993, e92, e36, F355, Z32, Jag Join Date: Sep 2010 Location: in the 416 iTrader: (3)	A proper looking setup. Very OEM looking. That is ultimately a huge selling point for me anyway. I'm looking forward to getting my device in the post. Any ETA when they will be shipping out?
	Appreciate 0 Quote

04-11-2011, 08:42 PM	#4
bimmertt Lieutenant Colonel 98 Rep 1,800 Posts Drives: 2007 e92 335i Join Date: Nov 2008 Location: Earth iTrader: (7)	so for this gauge to work, you just connect it to the OBD port?
	Appreciate 0 Quote

04-11-2011, 09:08 PM	#5
Kalud Lieutenant 29 Rep 582 Posts Drives: e92 335i Join Date: Jun 2010 Location: Canada iTrader: (0)	Very nice, great work!
	Appreciate 0 Quote

04-11-2011, 11:39 PM	#6
vasillalov Mad Linux Guru On The Loose 1198 Rep 5,455 Posts Drives: 2008 335i Sedan, 2023 M3 Join Date: Aug 2009 Location: Chicago, IL iTrader: (5) Garage List 2023 BMW M3 [0.00] 2008 335i E90 [8.00]	Is this connector going to be included with all gauge purchases? __________________
	Appreciate 0 Quote

04-12-2011, 03:58 PM	#10
2kaccordocoupe Brigadier General 1286 Rep 4,703 Posts Drives: Former ///M Driver Join Date: Nov 2008 Location: The 6ix iTrader: (2)	Nice
	Appreciate 0 Quote

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search