[Puerto Rican 335d]

Ok I went to the car and got it working but seems like the OBD II BT is working intermitently I got this message from time to time

Vehicle VIN: MY CAR
Vehicle Manufacturer: BMW
Vehicle Calibration ID: 8572131
8572402
NOX005
Test report:
------------------
ECU reports no test results present (Vehicle ECU may not support this mode)
End of report.

But when I got it to work this is what I copied from screen dont know what happened to th rest of the screen shotsa but I did read the EGR one and it stated it was defective or somewhat like that will try to do it later

[TDIwyse]

I don't think you put down the correct display ... The Readiness display should look something like this:

http://www.e90post.com/forums/showpo...&postcount=258

[Puerto Rican 335d]

Originally Posted by TDIwyse

I'm guessing this would be a problem then for you guys who live in states with inspections ...

Tdi i hv that out of all the gizmos it checks only two came completed i will try it again later

[TDIwyse]

Originally Posted by Puerto Rican 335d

Tdi i hv that out of all the gizmos it checks only two came completed i will try it again later

Thanks for the feedback. Looks like your tuner is also having a difficult time with all the emission stuff and is most likely having to remove certain faults so they don't turn on the SES light similar to Ecotune.

Would be interesting to see a screenshot of the OBD readiness parameters from someone with the Canada tune.

[Puerto Rican 335d]

Ok this is the screenshot I hav and i was telling you about, is this what you were talking about?

[Hoooper]

Well, you probably wouldnt pass like that because the tech would know its BS, but at least they dont say incomplete.

[TDIwyse]

Originally Posted by Puerto Rican 335d

Ok this is the screenshot I hav and i was telling you about, is this what you were talking about?

Yep, that's the one. Thanks.

Ditto what Hooper said.

Hope you enjoy the Torque App. It's very useful. The Track Recorder mode is also a lot of fun as you can record video while simultaneously showing parameters on the screen and then play back later.

[Puerto Rican 335d]

so its suffice to say that my code removal performed by Leentech is working I suspect

[Puerto Rican 335d]

TDi I will come forward if I disrespected you or anyone in the forum I apologize you and anyone. The torque reader is a tricky gimmick I need to get it mounted on the dash someway. Gracias for the input i have yet to do the dyno run been so busy lately

[135i_vs_]

Originally Posted by Puerto Rican 335d

Ok this is the screenshot I hav and i was telling you about, is this what you were talking about?

The reason it says "Not Available" is because of the Bluetooth Module you are using most likely. Or you have incorrect communication settings in the Torque app.

You can try watching it and see if it refreshes with data after 2 minutes.

If not, get a better Bluetooth Module.

However, it is definitely not Tune related.

[Puerto Rican 335d]

135 pls explain yourself on the communication settings

[TDIwyse]

Originally Posted by Puerto Rican 335d

The torque reader is a tricky gimmick I need to get it mounted on the dash someway.

I've been happy with this mount seen here: http://www.e90post.com/forums/showpo...45&postcount=5

It's from this place: http://www.mountek.com/

[TDIwyse]

Originally Posted by Puerto Rican 335d

135 pls explain yourself on the communication settings

Are you able to see any realtime data when using the app? If I'm not connected to the ECM then that Emissions Readiness screen just shows "Waiting for OBD Connection..." and nothing else is displayed there.

I've got 3 OBDII bluetooth dongles. The last one is the BMWhat specific one as my other 2 wouldn't work properly with the BMWhat app. But all of them work with Torque and have no issues showing the Emissions Readiness info. This is assuming you are actually connected to the ECM though via the bluetooth dongle...

[Hoooper]

Originally Posted by 135i_vs_

The reason it says "Not Available" is because of the Bluetooth Module you are using most likely. Or you have incorrect communication settings in the Torque app.

You can try watching it and see if it refreshes with data after 2 minutes.

If not, get a better Bluetooth Module.

However, it is definitely not Tune related.

Could also mean that the diagnostics have been removed in the tune. That is a generic list, its not unusual for several of them to show up as not available on a generic scanner. If you looked at a stock DDE you should see some that are not available such as secondary air system, evap system, heated catalyst, possibly fuel system.

A BMW scanner would only show the ones applicable, but a smog tech scanner will show all of them and some are always unavailable as far as I have seen

[Puerto Rican 335d]

tdi i have the ivini BMWHAT program and it will not comunicate so i gather we all hv the same issues w this program

tdi yes i can see boost revs etc etc on realtime data

[iaknown]

Most likely the monitors have been removed/disabled by the tuner (as Hooper alluded to). OBD readiness is not something that a slow BT module would fail to show especially since you have a connection and other parameters are showing ok.

[iaknown]

Rican, see what EGR info you can find by adding that parameter to the dashboard. Let us know what it's doing as well....

[135i_vs_]

Originally Posted by Puerto Rican 335d

135 pls explain yourself on the communication settings

Check your adapter settings. Should look like this and have "faster communication" enabled.

If tuner disabled monitors it will "not ready".
Something is definitely wrong with the module communication.

Add the EGR graph and see what it looks like. Mine is attached at cold idle.

[135i_vs_]

Originally Posted by Puerto Rican 335d

Ok this is the screenshot I hav and i was telling you about, is this what you were talking about?

On up top it should say connected to ECU OK (see my screenshot). On your screenshot it doesn't seem to say that. Just enable GPS on your phone when you use the Torque app or disable the request for it.

[Puerto Rican 335d]

135 I hv seen these and they were working I'll try it again later in the day

IAknown I have tried to do the graphing and it seems that EGT was not working or moving will try to do it over the weekend ok

[iaknown]

Originally Posted by Puerto Rican 335d

135 I hv seen these and they were working I'll try it again later in the day

IAknown I have tried to do the graphing and it seems that EGT was not working or moving will try to do it over the weekend ok

Make sure you are looking at EGR not EGT

[BB_cuda]

Originally Posted by iaknown

Make sure you are looking at EGR not EGT

+1