[2kaccordocoupe]

Originally Posted by Randall41

FiFo settings and com ports

current laptops usually only have 1 serial port at best. My Toshiba has 4 usb ports. USB ports are not designated by port no. It shouldn't matter which usb port you use. When the cable, in this case DCAN/ OBD/XXX or ? is inserted drivers must be downloaded and installed. This is usually done automatically. These drivers make the cable act as if it using Com ports.
Look in Control Panel/phones & Modems there should be at least 1 active port. Highlight and go to Advanced. There you will be able to adjust fifo settings.

Thanks for quick response and suggestion.
FIFO was already enabled so I set the Rx and Tx to 8 and rebooted. Still no luck, same IFH-0009 error. I figure maybe it was a power thing so I connected the laptop to AC power to make sure it was providing enough power. Any other ideas? Thx

[bmw_jason]

Anyone know how to get around this error message when trying to code the Windows up function. It pops up right when I click the Car/Key Memory button.

The error says

"GetIndividFswPsw"
"Individualisierung nicht moglich"

Anyone have any ideas at all?

[txusa03]

Originally Posted by 2kaccordocoupe

Thanks for quick response and suggestion.
FIFO was already enabled so I set the Rx and Tx to 8 and rebooted. Still no luck, same IFH-0009 error. I figure maybe it was a power thing so I connected the laptop to AC power to make sure it was providing enough power. Any other ideas? Thx

just curious, did you put the key into slot and press the start button?

[ebmiller88]

Noob question:

Welcome lights?? Not familiar. Thanks!

Ed

[jaza45]

Read the instructions again, you are picking the wrong option, thats why you are getting that error...

Originally Posted by bmw_jason

Anyone know how to get around this error message when trying to code the Windows up function. It pops up right when I click the Car/Key Memory button.

The error says

"GetIndividFswPsw"
"Individualisierung nicht moglich"

Anyone have any ideas at all?

[Pseudo Nim]

Originally Posted by ebmiller88

Noob question:

Welcome lights?? Not familiar. Thanks!

Ed

it's when you press the "unlock" button on your FOB - "which lights come on". by default it's blinkers + angels.

[2kaccordocoupe]

Originally Posted by txusa03

just curious, did you put the key into slot and press the start button?

I have CA, does the key still need to be in the slot?
INPA loads and shows battery and ignition with black dots so I assumed it was ok.

[txusa03]

Originally Posted by 2kaccordocoupe

I have CA, does the key still need to be in the slot?
INPA loads and shows battery and ignition with black dots so I assumed it was ok.

Try it with the KFob in the slot and let us know. I don't have CA.

[bmw_jason]

Originally Posted by ******

Read the instructions again, you are picking the wrong option, thats why you are getting that error...

I have read over the instructions 7 or 8 times and cannot see what I am doing wrong? Can you point me in the right direction?

Load profile > F1 > F3 > Select Chasis > Select ECU > Back > F5 > Error Pops Up????

[GenePoole]

Originally Posted by bmw_jason

I have read over the instructions 7 or 8 times and cannot see what I am doing wrong? Can you point me in the right direction?

Load profile > F1 > F3 > Select Chasis > Select ECU > Back > F5 > Error Pops Up????

No, not the procedure, but the options you changed is "nicht moeglich" (not possible). What option did you change in your FSW_PSW.MAN file?

[bmw_jason]

Originally Posted by GenePoole

No, not the procedure, but the options you changed is "nicht moeglich" (not possible). What option did you change in your FSW_PSW.MAN file?

I haven't Changed any options. I have been getting this error message since I first started coding. I have been able to code a few of the options as seen on the board through the regular modules but I cannot access the car/key memory at all without getting this error message.

What options could possibly be changed that create this error?

[spazticrecords]

Anyone know what these values do in CIC?

HVAC_POPUP_SEATCLIMATE
nicht_aktiv
HVAC_SEATCLIMATE_LED
nicht_aktiv

Has anyone also changed welcome lights. I need to know what values to change and what modules.

[jaza45]

Originally Posted by bmw_jason

I have read over the instructions 7 or 8 times and cannot see what I am doing wrong? Can you point me in the right direction?

Load profile > F1 > F3 > Select Chasis > Select ECU > Back > F5 > Error Pops Up????

thats because you are picking the wrong option on the basic functions menu

min: 7:20

[spazticrecords]

I am offering onsite coding this weekend in NY, westchester. PM ME for details if interested.

[BigZ88]

Anyone doing this in the upstate SC/Charlotte area?

[bmw_jason]

Originally Posted by ******

thats because you are picking the wrong option on the basic functions menu

min: 7:20

I watched the video and I signed the basic functions menu that you are talking about.

When would I change that function? The process I am using again is:

Load profile > F1 > F3 > Select Chasis > Select ECU > Back > F5 > Error Pops Up????

At which point would I change the basic function?

I tried playing around with the basic functions to get the car/key memory button to work and I still get the error.

I cant even get into the car/key menu at all!

[GenePoole]

Originally Posted by bmw_jason

I watched the video and I signed the basic functions menu that you are talking about.

When would I change that function? The process I am using again is:

Load profile > F1 > F3 > Select Chasis > Select ECU > Back > F5 > Error Pops Up????

At which point would I change the basic function?

I tried playing around with the basic functions to get the car/key memory button to work and I still get the error.

I cant even get into the car/key menu at all!

What is F5? I don't have one set in the profile I'm using. I just go to the ECU menu after the "back" above.

As far as I know, Car Key Memory (CKM) is a holdover from older BMWs and isn't applicable to E9x. (I know his option gets "greyed" out in Progman when you select E9x.)

Another thing to check is your FSW_PSW.MAN file. If it is corrupt or missing, you'll get this error. Even if you're not doing any manipulation, you must have the file present (it can be empty).

[spazticrecords]

Exactly,

Open your FSW_PSW.man and FSW_PSW.trc and delete everything in it and save it. If those files don't exist manually create them. I am not able to read key/car memory but maybe that's only on older cars as above says.

[GenePoole]

Originally Posted by spazticrecords

Exactly,

Open your FSW_PSW.man and FSW_PSW.trc and delete everything in it and save it. If those files don't exist manually create them. I am not able to read key/car memory but maybe that's only on older cars as above says.

From Progman Help:

E70, E71, E81, E82, E87, E88, E90, E91 E92 and E93
On these model series, all Car & Key Memory (CKM) functions are programmed directly in the vehicle (please refer to the section of the Owner's Manual headed "Personal profile": Individual settings for a maximum of 3 remote control modules via the display in the instrument cluster or via the Central Information Display)

[bmw_jason]

Originally Posted by spazticrecords

Exactly,

Open your FSW_PSW.man and FSW_PSW.trc and delete everything in it and save it. If those files don't exist manually create them. I am not able to read key/car memory but maybe that's only on older cars as above says.

Just tried it.....Still does't work


Oh Well!

Is there anythign in there thats worth while to code?

I was trying to get in there to code the windows up on the FOB but I manged to get it coded without the Car/Key Memory button.


Thanks for all the belp, by the way!

[spazticrecords]

@BMW_jason, so you were able to code the car or you weren't?

[bmw_jason]

Originally Posted by spazticrecords

@BMW_jason, so you were able to code the car or you weren't?

Yup - I can code it fine with the modules, just cannot get into the "Car/Key Memory" menu!