Inexpensive upgraded shock mounts - Monroe 907984

D's Bimmer · 03-15-2016, 01:51 PM

I am not going to use the metal washer that comes with the Monroe kit as it seems redundant. Any issues?

PrematureApex · 03-15-2016, 02:01 PM

So long as your stock washer/cup is in good shape, no reason to use it. See the recent thread in this forums for what I mean.

Murf · 03-15-2016, 02:58 PM

I left it out. Stock cap was fine.

ajaye · 03-17-2016, 10:29 AM

My Monroe kit is getting delivered today, but if the pictures are an indication, it may be wise to swap the stock support cap for the Monroe washer if you are in a cold climate that sees salted roads. Or at least paint/coat the stock cap. Corrosion of that stock cap appears to be how people's top rear shock mounts end up flopping around in the trunk.

gunnerxq · 03-21-2016, 10:58 AM

What do you guys think of the yellow powerflex upper shock mounts? I really can't find any reviews on them

mlifxs · 03-21-2016, 11:13 AM

Quote:

Originally Posted by gunnerxq

What do you guys think of the yellow powerflex upper shock mounts? I really can't find any reviews on them

this thread mentions them, though mainly about coilovers. op installed and eventually had noise concerns.
http://www.e90post.com/forums/showth...346&page=4

ajsalida · 03-21-2016, 11:15 AM

Quote:

Originally Posted by gunnerxq

What do you guys think of the yellow powerflex upper shock mounts? I really can't find any reviews on them

I have them on my car, they're fine. Cured an annoying small amplitude jiggling problem with the rear shocks. No squeaking or noises (make sure you use the supplied lube). Much firmer than stock mounts, mine were old and squishy. However if I'd known about the Monroe prior to buying I may have gone that way for cost purposes.

whosdady · 03-21-2016, 08:45 PM

Quote:

Originally Posted by HP Autosport

Quote:

Originally Posted by katsooba

do you happen to know if this fits the KW V3 rear shocks?
i dont know if the kw is 10 or 12mm
but i am almost certain my installer used the stock mounts when installed

The mounts don't matter, it's the sleeve that is either 10 or 12mm ID.

I have the yellow powerflex upper shock mounts on my olhins, but I want to switch them out for the powerflex black. Do you know what size I need? 10 or 12, I can't remember...

pits200 · 03-22-2016, 12:02 AM

Quote:

Originally Posted by whosdady

I have the yellow powerflex upper shock mounts on my olhins, but I want to switch them out for the powerflex black. Do you know what size I need? 10 or 12, I can't remember...

I just got the ohlin rts and am having a hard time reinstalling the adjuster knob. Not the extender or even the circular dial knob. I mean the portion you need to thread off so you can fit the mount on first. When I reattach it only allows me 18 clicks of adjustment on one side and 30 on the other. You have any suggestions?

whosdady · 03-23-2016, 09:35 AM

Quote:

Originally Posted by pits200

Quote:

Originally Posted by whosdady

I have the yellow powerflex upper shock mounts on my olhins, but I want to switch them out for the powerflex black. Do you know what size I need? 10 or 12, I can't remember...

I just got the ohlin rts and am having a hard time reinstalling the adjuster knob. Not the extender or even the circular dial knob. I mean the portion you need to thread off so you can fit the mount on first. When I reattach it only allows me 18 clicks of adjustment on one side and 30 on the other. You have any suggestions?

That's odd! I haven't played around with my Ohlins for a while. Hopefully I will have chance to check them out soon. If you haven't solved your issue by then, I will try to come up with a couple of suggestions...

feuer · 04-08-2016, 08:01 AM

Since recently there is lower rear shock mount available.
http://www.partsgeek.com/j4f4jzk-bmw...t+Mounting+Kit
I order them and they are coming on Tuesday 4-12-16 and I will review them after installation.

Murf · 04-08-2016, 08:06 AM

Quote:

Originally Posted by feuer

Since recently there is lower rear shock mount available.
http://www.partsgeek.com/j4f4jzk-bmw...t+Mounting+Kit
I order them and they are coming on Tuesday 4-12-16 and I will review them after installation.

Nice find. I would assume they use the same material as the uppers. When I switched out my shocks my lower mounts were in very good shape so I re-used them. That was 13k miles ago already so perhaps I will throw these in soon.

Looking forward to your review.

marconi118 · 04-08-2016, 12:21 PM

where to find these here in europe?

feuer · 04-08-2016, 12:44 PM

Quote:

Originally Posted by marconi118

where to find these here in europe?

Where are you located? Italy? If you want them I can help you but need to pre pay

jwebb335xi · 04-08-2016, 02:49 PM

Quote:

Originally Posted by Murf

Quote:

Originally Posted by feuer

Since recently there is lower rear shock mount available.
http://www.partsgeek.com/j4f4jzk-bmw...t+Mounting+Kit
I order them and they are coming on Tuesday 4-12-16 and I will review them after installation.

Nice find. I would assume they use the same material as the uppers. When I switched out my shocks my lower mounts were in very good shape so I re-used them. That was 13k miles ago already so perhaps I will throw these in soon.

Looking forward to your review.

Nice find. I think I paid about twice as much for each stock mount. Assuming these are comparable, they represent a big savings.

Dhillon92 · 04-11-2016, 08:38 PM

I'm about to order ST (by kW) coilovers and was wondering if these shock mounts will fit them. Would the sleeve insert fit or would I need to open it up a bit?

Thanks

Edit: Feuer, also looking forward to seeing if the lower shock mount fits, thanks!

screaminfast · 04-12-2016, 08:48 AM

Quote:

Originally Posted by Dhillon92

I'm about to order ST (by kW) coilovers and was wondering if these shock mounts will fit them. Would the sleeve insert fit or would I need to open it up a bit?

Thanks

Edit: Feuer, also looking forward to seeing if the lower shock mount fits, thanks!

Same here. I have ST already in the car.

Dhillon92 · 04-13-2016, 07:09 PM

I went ahead and ordered the top and bottom shock mounts. Will arrive April 26, will install them along with the ST

feuer · 04-13-2016, 10:33 PM

Quote:

Originally Posted by Murf

Nice find. I would assume they use the same material as the uppers. When I switched out my shocks my lower mounts were in very good shape so I re-used them. That was 13k miles ago already so perhaps I will throw these in soon.

Looking forward to your review.

Quote:

Originally Posted by jwebb335xi

Nice find. I think I paid about twice as much for each stock mount. Assuming these are comparable, they represent a big savings.

Quote:

Originally Posted by Dhillon92

I'm about to order ST (by kW) coilovers and was wondering if these shock mounts will fit them. Would the sleeve insert fit or would I need to open it up a bit?

Thanks

Edit: Feuer, also looking forward to seeing if the lower shock mount fits, thanks!

The delivery was delayed. I order directry to avoid shiiping fee on shop account. They were schedule for delivery yesturday. Didn't arrive today either. If they arrive by Fiday I will install them over the weekend. Can't wait honestly because I have one bad shock bump stop thar I need to replace as well.

bobchuong58 · 04-14-2016, 06:18 PM

American made Rubber is way better than German's.

marconi118 · 04-15-2016, 10:00 AM

Quote:

Originally Posted by feuer

Where are you located? Italy? If you want them I can help you but need to pre pay

I am in Germany...

feuer · 04-15-2016, 10:07 AM

Quote:

Originally Posted by marconi118

I am in Germany...

PM me you address and I can tell you how much is going to be from shipping. I need to go to the postal office anyhow tomorrow.

03-15-2016, 01:51 PM	#89
D's Bimmer Major 243 Rep 1,328 Posts Drives: 2016 340 Xi Join Date: Nov 2011 Location: Toronto iTrader: (1)	I am not going to use the metal washer that comes with the Monroe kit as it seems redundant. Any issues?
	Appreciate 0 Quote

03-15-2016, 02:01 PM	#90
PrematureApex Colonel 848 Rep 2,411 Posts Drives: N55 X1, N54 135, s54 m3 Join Date: Jan 2008 Location: Philadelphia iTrader: (0)	So long as your stock washer/cup is in good shape, no reason to use it. See the recent thread in this forums for what I mean. __________________ '02 S54 M3 (500/500 GC/Koni) '08 N54 135 (JB4, DCI, BMW PS/Bilstein B6s, H&R M3 FSB, Strongflex FCABs) '14 N55 X1 (JB4, BMS DP, BMS Intake, Alpina TCU reflash, H&R Sports, Bilstein B6s, E93 M3 RSB, Strongflex FCABs, baby seat) '08 N54 535xi touring (Bilstein B6s, Downpipes, MHD tune, baby seat)
	Appreciate 0 Quote

03-15-2016, 02:58 PM	#91
Murf Captain 905 Rep 897 Posts Drives: 2021 G80 M3C - Dravit Grey Join Date: Apr 2011 Location: Florida iTrader: (2)	I left it out. Stock cap was fine.
	Appreciate 0 Quote

03-17-2016, 10:29 AM	#92
ajaye Second Lieutenant 31 Rep 228 Posts Drives: 07 328xi SGM Join Date: Dec 2014 Location: Pittsburgh iTrader: (0)	My Monroe kit is getting delivered today, but if the pictures are an indication, it may be wise to swap the stock support cap for the Monroe washer if you are in a cold climate that sees salted roads. Or at least paint/coat the stock cap. Corrosion of that stock cap appears to be how people's top rear shock mounts end up flopping around in the trunk.
	Appreciate 1 Quote

03-21-2016, 10:58 AM	#93
gunnerxq Lieutenant Colonel 222 Rep 1,805 Posts Drives: 2015 335i xDrive 6MT Join Date: Sep 2010 Location: New York iTrader: (1)	What do you guys think of the yellow powerflex upper shock mounts? I really can't find any reviews on them __________________ Former E90 325i: Koni special active red, eibach pro-kit springs, Remus exhaust, stage 3 intake manifold,Stage 2 AA tune, BMW Short shift kit. Silicon intake pipe. M3 control arms front, M3 rear. ECS trailing arm with whiteline bushings. Purple powerflex subframe bushings. Yellow power flex upper shock mounts. Single mass flywheel OE weight.
	Appreciate 0 Quote

04-08-2016, 08:01 AM	#99
feuer Major General 4285 Rep 9,222 Posts Drives: wife crazy! Join Date: Apr 2015 Location: Chicago, IL iTrader: (5)	Since recently there is lower rear shock mount available. http://www.partsgeek.com/j4f4jzk-bmw...t+Mounting+Kit I order them and they are coming on Tuesday 4-12-16 and I will review them after installation.
	Appreciate 0 Quote

04-08-2016, 12:21 PM	#101
marconi118 Major 96 Rep 1,186 Posts Drives: 06/07 e93 335i Join Date: Nov 2008 Location: europe iTrader: (0)	where to find these here in europe?
	Appreciate 0 Quote

04-11-2016, 08:38 PM	#104
Dhillon92 Captain 82 Rep 605 Posts Drives: '11 335xi Join Date: Jul 2014 Location: Toronto iTrader: (0)	I'm about to order ST (by kW) coilovers and was wondering if these shock mounts will fit them. Would the sleeve insert fit or would I need to open it up a bit? Thanks Edit: Feuer, also looking forward to seeing if the lower shock mount fits, thanks!
	Appreciate 0 Quote

04-13-2016, 07:09 PM	#106
Dhillon92 Captain 82 Rep 605 Posts Drives: '11 335xi Join Date: Jul 2014 Location: Toronto iTrader: (0)	I went ahead and ordered the top and bottom shock mounts. Will arrive April 26, will install them along with the ST
	Appreciate 0 Quote

04-14-2016, 06:18 PM	#108
bobchuong58 Private 6 Rep 56 Posts Drives: Black E90 Join Date: May 2011 Location: San Jose, ca iTrader: (0)	American made Rubber is way better than German's.
	Appreciate 0 Quote

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search