E90Post
 


 
BMW 3-Series (E90 E92) Forum > E90 / E92 / E93 3-series Technical Forums > Mechanical Maintenance: Break-in / Oil & Fluids / Servicing / Warranty > oil change problem.....cant fix it - help!



Reply
 
Thread Tools Search this Thread
      05-08-2010, 09:43 AM   #1
max_asdf
Private First Class
22
Rep
176
Posts

Drives: e90
Join Date: Sep 2009
Location: ca

iTrader: (1)

oil change problem.....cant fix it - help!

ok, went to do a simple oil change.

when done, i checked the oil level, it was half. i drove it for 30minutes, it went to miniumum and add 1Q of oil.

So I went to add more, the oil sensor shows maximum now. turned the car off and on again. still at maximum.


I go to turn it on again after 5minutes to drive it, the oil gauge shows 3/4 to max only.

this morning it only showed half full.


What is going on??
Appreciate 0
      05-08-2010, 12:11 PM   #2
bmw6953
Second Lieutenant
25
Rep
257
Posts

Drives: 2006 325i
Join Date: Oct 2008
Location: california

iTrader: (0)

have you made sure you car is not leaking oil any where? if not maybe you need a new oil level sensor or the oil isnt properly circulating.
Appreciate 0
      05-08-2010, 01:11 PM   #3
mike3000fl
Banned
No_Country
138
Rep
2,731
Posts

Drives: 06 330i
Join Date: Feb 2010
Location: Tampa

iTrader: (0)

so how many quarts total did you put in there? provided there are no leaks whatever you put in should still be in there.

with that....look for leaks, since you only pulled the drain plug you could just remove the trapdoor for a day or two so leaks will hit the ground and be visible.

you might want to pull the filter and make sure it's not crush and is seated correctly, not sure if that would cause the strange readings or not but worth checking.

a blockage might cause strange readings, i always make sure to remove all the foil from the cap by hand before i go pouring it in the engine just in case a piece comes off and gets in my motor blocking passageways.

as long as there are no leaks and no blockages, if you know you put enough oil in there running the motor should be fine. i would let it warm up and try to check it consistantly under the same conditions to get a good baseline reading.
Appreciate 0
      05-08-2010, 08:29 PM   #4
fdriller9
Banned
United_States
260
Rep
7,089
Posts

Drives: '06 AW 330xi
Join Date: Mar 2009
Location: North Jersey/Philly/NYC

iTrader: (4)

Garage List
2006 330xi  [6.44]
Are you getting these reading on a level surface? You should be.
Appreciate 0
      05-08-2010, 09:46 PM   #5
ENINTY
Banned
182
Rep
3,415
Posts

Drives: 2006 325i Sport
Join Date: Jun 2006
Location: Virginia

iTrader: (0)

Oil change:

Open oil filter cap.

Open drain.

Let oil drain out.

Suck and remaining oil from the filter housing.

clean and then replace the filter.

Close drain bolt.

Add SEVEN (7) QUARTS of BMW oil.

You're finished.
Appreciate 0
      05-08-2010, 10:03 PM   #6
bmw6953
Second Lieutenant
25
Rep
257
Posts

Drives: 2006 325i
Join Date: Oct 2008
Location: california

iTrader: (0)

you need 7 quarts total no more no less
Appreciate 0
      05-17-2010, 10:09 PM   #7
Delanez
New Member
3
Rep
25
Posts

Drives: 04 325i
Join Date: Apr 2010
Location: Wisconsin

iTrader: (1)

How many quarts did you use for the oil change? If it's 7 then you have a defective oil level sensor. If you're not sure then drain the oil out and measure it.

Be nice to have a dipstick eh? how silly.....
Appreciate 0
Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 02:03 PM.




e90post
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST