What part # is this? Help! hard plumming vacuum line?

235Dude · 10-10-2010, 09:16 PM

While I was looking in the engine bay I noticed this part circled was loose. There is a little plastic ring connector that seems to have snapped in half.

Does anyone know what this is and the part number? I read somewhere it might be the hard plumming vacuum line but I couldnt find it on getbmwparts.com. I added some electrical tape for now to seal it.

ren · 10-10-2010, 09:30 PM

http://www.e90post.com/forums/showthread.php?t=130596

235Dude · 10-10-2010, 09:50 PM

Quote:

Originally Posted by erensf

http://www.e90post.com/forums/showthread.php?t=130596

Thanks

For anyone else the part number is 11667570497 if you have an 07 with oil cooler. $22 from getbmwparts.com

possible335i2008 · 11-02-2010, 02:14 PM

I just recieved this part how do you install..I havent looked at it yet but was wondering if there are any pointers to doing it

cn555ic · 11-02-2010, 02:27 PM

That piece looks to be heat fitted ..I would think getting that joint hot and then pulling it off...

possible335i2008 · 11-02-2010, 02:32 PM

could I use a hair dryer...sorry stupid question but don't have a heat gun

Quote:

Originally Posted by cn555ic

That piece looks to be heat fitted ..I would think getting that joint hot and then pulling it off...

possible335i2008 · 11-02-2010, 04:59 PM

Bump for install pointers

cn555ic · 11-02-2010, 05:13 PM

Quote:

Originally Posted by possible335i2008

could I use a hair dryer...sorry stupid question but don't have a heat gun

I think it should be fine, some of these hair dryers are quite hot....Just make sure to pull it off without cracking the tubing or yanking it too hard..

possible335i2008 · 11-03-2010, 12:50 AM

Just got done doing this the part I ordered was the whole pipe that conects to the 90 degree bend that is located under the drivers side plastic cover where their are the liquid reservoirs...either Way no need for a heat gun there is a small white piece that can be pushed in releasing the pipe really easy once you know what you are looking for thanks everyone for there help

10-10-2010, 09:16 PM	#1
235Dude Captain 107 Rep 925 Posts Drives: 2016 M235i Join Date: Feb 2009 Location: Potomac, MD iTrader: (19)	What part # is this? Help! hard plumming vacuum line? While I was looking in the engine bay I noticed this part circled was loose. There is a little plastic ring connector that seems to have snapped in half. Does anyone know what this is and the part number? I read somewhere it might be the hard plumming vacuum line but I couldnt find it on getbmwparts.com. I added some electrical tape for now to seal it. __________________ 2016 M235i \| BSM \| 6SPD \| BMS JB4 \| Dinan Intake \| Wagner Evo 2 Comp IC \| VRSF DP \| ER CP \| Dinan Exhaust \| M Performance LSD \| M Performance Springs Gone: 2016 F30 340i, 2015 Corvette Z06, 2011 E92 335i, 2007 E92 335i, 2008 Corvette Z51, 1999 E46 323i, 2001 Boxster, 1999 Carrera 2, 1997 Corvette, 2001 Camaro SS
	Appreciate 0 Tweet Quote

10-10-2010, 09:30 PM	#2
ren Captain 62 Rep 840 Posts Drives: 2024 X7 M60i Join Date: Jan 2007 Location: U.S. iTrader: (8)	http://www.e90post.com/forums/showthread.php?t=130596
	Appreciate 0 Quote

11-02-2010, 02:14 PM	#4
possible335i2008 Major 182 Rep 1,222 Posts Drives: 335i Join Date: Mar 2008 Location: united states iTrader: (10)	I just recieved this part how do you install..I havent looked at it yet but was wondering if there are any pointers to doing it
	Appreciate 0 Quote

11-02-2010, 02:27 PM	#5
cn555ic 460 Rep 18,331 Posts Drives: 335i Join Date: Jun 2007 Location: US iTrader: (6)	That piece looks to be heat fitted ..I would think getting that joint hot and then pulling it off...
	Appreciate 0 Quote

11-02-2010, 04:59 PM	#7
possible335i2008 Major 182 Rep 1,222 Posts Drives: 335i Join Date: Mar 2008 Location: united states iTrader: (10)	Bump for install pointers
	Appreciate 0 Quote

11-03-2010, 12:50 AM	#9
possible335i2008 Major 182 Rep 1,222 Posts Drives: 335i Join Date: Mar 2008 Location: united states iTrader: (10)	Just got done doing this the part I ordered was the whole pipe that conects to the 90 degree bend that is located under the drivers side plastic cover where their are the liquid reservoirs...either Way no need for a heat gun there is a small white piece that can be pushed in releasing the pipe really easy once you know what you are looking for thanks everyone for there help
	Appreciate 0 Quote

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search