Ever seen this with your Procede?

Zasquatch · 11-01-2010, 08:19 PM

I will start by saying I have a call and a PM to Vishnu, so I am sure this will get figured out, but I wanted to see if anyone has seen this with their Procede.

I got my Procede V4 in the mail today and commenced installing it. I really didn't realize it was that easy. I had the install video on my Iphone right next to me, and took my sweet time... and it still only took about 20 minutes. Sweet.

Firmware is #22 with the associated 6MT map.

I went into the car and reset everything (via the command center). I then went for a test drive. Here's where it started getting messy.

Anytime I would give more than half throttle, or go above 8-9 psi, the car would start shuttering like crazy. A yellow CEL light pops up, and the car continues to run like sh*t. I shut the car off and turn it back on, and the car acts like nothing ever happened. Runs fine until about half throttle or 8 psi.

I hooked up my laptop and uploaded the latest firmware (#29) and map for 6MT and the same thing happened.

Any hunches? With the new map/FW, which setting is valet/bypass mode? I'd like to bypass the Procede until I can figure out what the issue is.. without having to take it out again.

I'm sure Vishnu will help me out, but in the meantime I'd appreciate your input.

Thanks guys.

OpenFlash · 11-01-2010, 08:44 PM

Did you get the Procede directly from us? Either way, give us a call tomorow and we can help you troubleshoot. If you got it used, I'd recommend sending it back to us for free testing/udpating. In the meantime, you can run in valet mode by toggling over to map0. You can do this by double-clicking the DTC button. Or by holding the cruise control stalk down until the tach shows 0RPM. This must be done while the car is running

Shiv

Brey335i · 11-01-2010, 08:47 PM

+ 1. Definitely take advantage of their free testing if you can't get this solved.

BrianMN · 11-01-2010, 08:57 PM

What codes are being thrown?

Zasquatch · 11-01-2010, 09:32 PM

Quote:

Originally Posted by shiv@vishnu

Did you get the Procede directly from us? Either way, give us a call tomorow and we can help you troubleshoot. If you got it used, I'd recommend sending it back to us for free testing/udpating. In the meantime, you can run in valet mode by toggling over to map0. You can do this by double-clicking the DTC button. Or by holding the cruise control stalk down until the tach shows 0RPM. This must be done while the car is running

Shiv

Shiv, thanks for the quick response. I'll give you a call sometime tomorrow. Against my better judgment I took a chance getting one used. Does this effect any sort of "warranty" vs. getting direct from you? What is involved in the testing/updating? If the unit is faulty are the necessary repairs considered updating?

I guess I'm trying to ask.... am I screwed and should I try to return it, or is this something that gets resolved regardless of where I got it from?

Not sure of the codes, I checked them before I cleared them, so I assume I can read them before I uninstall it?

335xiRT1 · 11-01-2010, 09:44 PM

I thought resetting everything In the command center all at one time was a bad thing?

Zasquatch · 11-01-2010, 09:54 PM

Quote:

Originally Posted by 335xiRT1

I thought resetting everything In the command center all at one time was a bad thing?

I actually messed up the order of things a little bit... I reset everything after loading the new firmware didn't change anything. After resetting, the results were the same.

girmis · 11-01-2010, 09:58 PM

I had similar issue. I am still waiting for shiv to send me instructions how to disable O2 simulation (now it is 2 weeks). Shiv, anytime soon?

OpenFlash · 11-01-2010, 10:01 PM

Quote:

Originally Posted by girmis

I had similar issue. I am still waiting for shiv to send me instructions how to disable O2 simulation (now it is 2 weeks). Shiv, anytime soon?

I'll be releasing that how-to along with firmware 130. The firmware update taking longer than expected to test. Lots of new stuff. Will be this week.

OpenFlash · 11-01-2010, 10:25 PM

Quote:

Originally Posted by Annino

Shiv, thanks for the quick response. I'll give you a call sometime tomorrow. Against my better judgment I took a chance getting one used. Does this effect any sort of "warranty" vs. getting direct from you? What is involved in the testing/updating? If the unit is faulty are the necessary repairs considered updating?

I guess I'm trying to ask.... am I screwed and should I try to return it, or is this something that gets resolved regardless of where I got it from?

Not sure of the codes, I checked them before I cleared them, so I assume I can read them before I uninstall it?

Purchasing anything used is somewhat of a risk. But we will still honor the warranty and fix whatever needs to be fixed. Just call us tomorrow and get an RMA number. Then just ship it to us and we will take care of whatever needs to be taken care of. No worries at all.

Shiv

jfawns76 · 11-01-2010, 10:30 PM

Quote:

Originally Posted by shiv@vishnu

Purchasing anything used is somewhat of a risk. But we will still honor the warranty and fix whatever needs to be fixed. Just call us tomorrow and get an RMA number. Then just ship it to us and we will take care of whatever needs to be taken care of. No worries at all.

Shiv

Gotta love the customer service!

Zasquatch · 11-01-2010, 10:38 PM

Wow. Awesome, makes me even happier I went the Vishnu route, even if it was used

Sparky66 · 11-02-2010, 02:51 AM

Quote:

Originally Posted by girmis

I had similar issue. I am still waiting for shiv to send me instructions how to disable O2 simulation (now it is 2 weeks). Shiv, anytime soon?

It's simple to disable............open the "User Adjustable Settings" under the "User Maps" tab in your Procede User Software and set the O2 Modifier to 100%. Adjusting the setting to less than 100%, will reduce the output range to the rear O2 sensors, which is needed to run catless DP's.

Zasquatch · 11-03-2010, 11:25 AM

I overnighted the Procede to Shiv, they should get it first thing this morning. I'm really hoping it's an easy fix.

I've got lots of practice with the install, I'm down to 15 minutes now

e93WhiteonRed · 11-03-2010, 11:31 AM

Sounds like he's taking care of you - really good to see!! I just made the switch to PROcede and can't believe how superior the product is...

You'll enjoy it once it's running smooth.

cn555ic · 11-03-2010, 11:34 AM

Quote:

Originally Posted by e93WhiteonRed

Sounds like he's taking care of you - really good to see!! I just made the switch to PROcede and can't believe how superior the product is...

You'll enjoy it once it's running smooth.

lol...I tried to let you know awhile ago but you bashed me about being a fanboy of Procede in one of the threads, I am glad you finally see it for yourself!

Undies · 11-03-2010, 11:54 AM

Quote:

Originally Posted by shiv@vishnu

Purchasing anything used is somewhat of a risk. But we will still honor the warranty and fix whatever needs to be fixed. Just call us tomorrow and get an RMA number. Then just ship it to us and we will take care of whatever needs to be taken care of. No worries at all.

Shiv

i love my procede. i also love the customer service. its rare to find this combination in anything i buy these days.

i will buy another car that procede has a product for, thats how much i love these guys.

e93WhiteonRed · 11-03-2010, 11:57 AM

I bashed you?? you sure?? not really my type to do that. I'll have to look. If that's the case, then I'm a friggin idiot because it's like night and day....

**335i** · 11-03-2010, 12:00 PM

what i would like that vishnu team respond to pms and emails quicker

Zasquatch · 11-03-2010, 02:19 PM

Quote:

Originally Posted by **335i**

what i would like that vishnu team respond to pms and emails quicker

Just call them if it's urgent, if it's within business hours they usually pick up.

vase330 · 11-03-2010, 03:04 PM

The dude is on Eastern European Time Zon3e out in Lithuania I think, so what do you expect? Shiv probably snoring and drooling into his pillow when he sends his PMs or Calls.

Zasquatch · 11-03-2010, 03:17 PM

Hahaha yeah I guess I missed that minor detail....

11-01-2010, 08:19 PM	#1
Zasquatch Captain 36 Rep 708 Posts Drives: '07 BMW 335i Join Date: Sep 2010 Location: CT iTrader: (15) Garage List 2007 BMW 335i [0.00]	Ever seen this with your Procede? I will start by saying I have a call and a PM to Vishnu, so I am sure this will get figured out, but I wanted to see if anyone has seen this with their Procede. I got my Procede V4 in the mail today and commenced installing it. I really didn't realize it was that easy. I had the install video on my Iphone right next to me, and took my sweet time... and it still only took about 20 minutes. Sweet. Firmware is #22 with the associated 6MT map. I went into the car and reset everything (via the command center). I then went for a test drive. Here's where it started getting messy. Anytime I would give more than half throttle, or go above 8-9 psi, the car would start shuttering like crazy. A yellow CEL light pops up, and the car continues to run like sh*t. I shut the car off and turn it back on, and the car acts like nothing ever happened. Runs fine until about half throttle or 8 psi. I hooked up my laptop and uploaded the latest firmware (#29) and map for 6MT and the same thing happened. Any hunches? With the new map/FW, which setting is valet/bypass mode? I'd like to bypass the Procede until I can figure out what the issue is.. without having to take it out again. I'm sure Vishnu will help me out, but in the meantime I'd appreciate your input. Thanks guys.
	Appreciate 0 Tweet Quote

11-01-2010, 08:47 PM	#3
Brey335i Banned 118 Rep 4,771 Posts Drives: e46 ///M3 Join Date: Oct 2009 Location: Austin, TX iTrader: (11)	+ 1. Definitely take advantage of their free testing if you can't get this solved.
	Appreciate 0 Quote

11-01-2010, 08:57 PM	#4
BrianMN Banned 117 Rep 2,428 Posts Drives: 4 Door Family Sedan Join Date: Sep 2009 Location: Minneapolis iTrader: (7)	What codes are being thrown?
	Appreciate 0 Quote

11-01-2010, 09:44 PM	#6
335xiRT1 Captain 47 Rep 693 Posts Drives: 2007 335i Join Date: Oct 2008 Location: long island iTrader: (14)	I thought resetting everything In the command center all at one time was a bad thing?
	Appreciate 0 Quote

11-01-2010, 09:58 PM	#8
girmis New Member 3 Rep 14 Posts Drives: 2008 535i Join Date: Mar 2009 Location: Chicago iTrader: (0)	I had similar issue. I am still waiting for shiv to send me instructions how to disable O2 simulation (now it is 2 weeks). Shiv, anytime soon?
	Appreciate 0 Quote

11-01-2010, 08:44 PM	#2
OpenFlash 1806 Rep 17,960 Posts Drives: A Lot Join Date: Sep 2006 Location: SF Bay, CA iTrader: (0) Garage List 2018 Ducati Panigal ... [0.00] 2016 Mazda CX5 [0.00] 2017 Aprilia Tuono ... [0.00] 2019 BMW M2 Competi ... [0.00] 2015 BMW M5 Competi ... [10.00] 2016 Ducati XDiavel S [0.00] 2016 AMG GT S [0.00] 2011 Ferrari 458 It ... [0.00] 2017 Charger Hellcat [0.00] 2015 KTM Super Duke ... [0.00] 2016 KTM RC390 [0.00]	Did you get the Procede directly from us? Either way, give us a call tomorow and we can help you troubleshoot. If you got it used, I'd recommend sending it back to us for free testing/udpating. In the meantime, you can run in valet mode by toggling over to map0. You can do this by double-clicking the DTC button. Or by holding the cruise control stalk down until the tach shows 0RPM. This must be done while the car is running Shiv
	Appreciate 0 Quote

11-01-2010, 10:38 PM	#12
Zasquatch Captain 36 Rep 708 Posts Drives: '07 BMW 335i Join Date: Sep 2010 Location: CT iTrader: (15) Garage List 2007 BMW 335i [0.00]	Wow. Awesome, makes me even happier I went the Vishnu route, even if it was used Last edited by Zasquatch; 11-01-2010 at 10:46 PM..
	Appreciate 0 Quote

11-03-2010, 11:25 AM	#14
Zasquatch Captain 36 Rep 708 Posts Drives: '07 BMW 335i Join Date: Sep 2010 Location: CT iTrader: (15) Garage List 2007 BMW 335i [0.00]	I overnighted the Procede to Shiv, they should get it first thing this morning. I'm really hoping it's an easy fix. I've got lots of practice with the install, I'm down to 15 minutes now
	Appreciate 0 Quote

11-03-2010, 11:31 AM	#15
e93WhiteonRed Second Lieutenant 19 Rep 267 Posts Drives: 2007 E93 Alpine white with Red Join Date: Jul 2010 Location: Reston, Virginia iTrader: (3) Garage List 2007 335I E93 [0.00]	Sounds like he's taking care of you - really good to see!! I just made the switch to PROcede and can't believe how superior the product is... You'll enjoy it once it's running smooth. __________________ 2007 335I E93 sport package Alpine White. BMS DCI, PROcede V4, ACT street clutch, Michelin Pilot Sport A/S Plus and BT Tool. Pending install of Raceland Downpipes.
	Appreciate 0 Quote

11-03-2010, 11:57 AM	#18
e93WhiteonRed Second Lieutenant 19 Rep 267 Posts Drives: 2007 E93 Alpine white with Red Join Date: Jul 2010 Location: Reston, Virginia iTrader: (3) Garage List 2007 335I E93 [0.00]	I bashed you?? you sure?? not really my type to do that. I'll have to look. If that's the case, then I'm a friggin idiot because it's like night and day.... __________________ 2007 335I E93 sport package Alpine White. BMS DCI, PROcede V4, ACT street clutch, Michelin Pilot Sport A/S Plus and BT Tool. Pending install of Raceland Downpipes.
	Appreciate 0 Quote

11-03-2010, 12:00 PM	#19
335i Colonel 188 Rep 2,320 Posts Drives: TOYOTA & 2008 E92 335i 6MT Join Date: Jul 2007 Location: Swiss iTrader: (4) Garage List 2008 335i [9.00]	what i would like that vishnu team respond to pms and emails quicker __________________ E92 335i Black Saphire 6MT PROcede V5, BMS DCI, Big Tom IC, AR CL-DP's 3", AR Design OC, Forge DV's, OEM M3 side skirts, BMW Performance Wheels 19 inch 269 Black Gloss+Continental ContiSportContact 5P (400hp and 550nm) https://www.youtube.com/user/aistis7..._as=subscriber
	Appreciate 0 Quote

11-03-2010, 03:04 PM	#21
vase330 Colonel 103 Rep 2,760 Posts Drives: 19 E63S; 15.5 RangeRover ATB Join Date: Jan 2007 Location: Arlington, Va iTrader: (1)	The dude is on Eastern European Time Zon3e out in Lithuania I think, so what do you expect? Shiv probably snoring and drooling into his pillow when he sends his PMs or Calls. __________________ E92 335 \| Space Gray \| Saddle Brown Dakota \| Dark Burl Trim \| ZPP \| ZSP \| AT \| Idrive \| 6FL \| FBO \| Dinan CAI \| Quaife LSD \| STG3 PROCede.
	Appreciate 0 Quote

11-03-2010, 03:17 PM	#22
Zasquatch Captain 36 Rep 708 Posts Drives: '07 BMW 335i Join Date: Sep 2010 Location: CT iTrader: (15) Garage List 2007 BMW 335i [0.00]	Hahaha yeah I guess I missed that minor detail....
	Appreciate 0 Quote

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search