|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Search | Today's Posts | Mark Forums Read |
|
BMW 3-Series (E90 E92) Forum
>
Procede install issues - help please.
|
|
11-28-2010, 09:28 AM | #1 |
Major General
189
Rep 6,631
Posts |
Procede install issues - help please.
I know this is a tough time for Vishnu to get back to me with some help (Sunday on Thanksgiving weekend) so I figured I'd ask the forum for a little help in case they don't get back to me.
I have a 2009 335i e90 with i-Drive. The DME software should be reasonably recent and MSD81. My issue here is an SES light and none of the CAN-related features are working! Car starts up, idles smoothly, but there is an SES light on the dash that I can't read or clear since none of the features work! CANclear, DTC map switching, Hazard gauge switching, Command Center, none of them work! I was digging through this entire board for the last two hours trying to figure out which harness/pins the CANbus is read through with no pertinent information. Did anyone else experience this? The only bit of information I could dig up was that CANclear doesn't work on older DME software, but that isn't the case for me.
__________________
E90 LCI N54 6AT
|
11-28-2010, 11:09 AM | #3 |
Major General
189
Rep 6,631
Posts |
I'll revert to an earlier known good FW revision and see what happens. Thanks for responding, much appreciated.
__________________
E90 LCI N54 6AT
|
Appreciate
0
|
11-28-2010, 11:20 AM | #4 |
Major General
161
Rep 7,377
Posts |
No need to revert. Just redownload latest FW and maps and upload them. If you still get the issue check the procede connection in the ECU.
__________________
07 335i AT - MOTIV 750 - MHD E85 BMS flash - BMS PI - JB4G5 - Okada Coils - NGK 5992 Plugs - Helix IC - Snow Stg. 3 - Stett CP - Custom midpipes with 100 HJS Cats - Bastuck Quad - PSS10 - QUAIFE LSD - BMS OCC - Forge DVs - AR OC - ALCON BBK - M3 Chassi - Dinan CP - Velocity M rear Toe arms - Advan RZ-DF - LUX H8 - Level 10 AT upgrade
|
Appreciate
0
|
11-28-2010, 01:12 PM | #5 |
1809
Rep 17,960
Posts
Drives: A Lot
Join Date: Sep 2006
Location: SF Bay, CA
iTrader: (0)
Garage List 2018 Ducati Panigal ... [0.00]
2016 Mazda CX5 [0.00] 2017 Aprilia Tuono ... [0.00] 2019 BMW M2 Competi ... [0.00] 2015 BMW M5 Competi ... [10.00] 2016 Ducati XDiavel S [0.00] 2016 AMG GT S [0.00] 2011 Ferrari 458 It ... [0.00] 2017 Charger Hellcat [0.00] 2015 KTM Super Duke ... [0.00] 2016 KTM RC390 [0.00] |
op- you have email.
|
Appreciate
0
|
11-28-2010, 01:45 PM | #6 |
Major General
189
Rep 6,631
Posts |
shiv -no email yet. Your e-mail server sucks
Anyway, reuploaded firmware numerous times, still can't access any of the CAN related features but SES light is gone. took tune out, SES light still gone. I think what I need to do is completely wipe the PROcede altogether and start from scratch but unsure on how to do that... Will wait for Shiv's e-mail thanks.
__________________
E90 LCI N54 6AT
|
Appreciate
0
|
11-28-2010, 08:42 PM | #7 |
Captain
15
Rep 603
Posts |
ECU Connector Part Numbers
If you don't mind can you jot down the ECU connector part numbers, I'm thinking of ordering a pair for the Procede harness so I don't have to pop off the slider and go through that exercise every time...
Unless shiv know the part numbers already. |
Appreciate
0
|
11-28-2010, 09:11 PM | #11 |
Major General
189
Rep 6,631
Posts |
No idea really. Car was acting wonky, i just removed the tune, test drove stock, reinstalled tune, went to the last known working firmware and it started working.
I'm on beta 131 right now on 6AT maps. PS - DOWNPIPES ARE A PAIN IN THE FUCKING COCK!!!!!!!!!!
__________________
E90 LCI N54 6AT
|
Appreciate
0
|
11-28-2010, 09:43 PM | #12 |
464
Rep 18,331
Posts |
Yes they are! PITA
|
Appreciate
0
|
Bookmarks |
Thread Tools | Search this Thread |
|
|