How many OEM parts did you break while installing stuff in your car ? :)

tscdennab · 01-03-2011, 06:01 PM

I have replaced an ECU cover and an air conditioning cowling until now, both damaged when trying to get the ECU out of the car...anyone else ?

Forcefed3 · 01-03-2011, 06:13 PM

How do you damage the ECU cover?

And I have lost a few bolts, but thats it.

Dmacc · 01-03-2011, 06:16 PM

I've lost two bolts for the air conditioning cover and I've snapped one of my connector pins for the ecu

I had to sauder it back together, then file it down enough so it could fit back in the original pin hole, it barely fits

Forcefed3 · 01-03-2011, 06:30 PM

Quote:

Originally Posted by Dmacc

I've lost two bolts for the air conditioning cover and I've snapped one of my connector pins for the ecu

I had to sauder it back together, then file it down enough so it could fit back in the original pin hole, it barely fits

Wow, that really sucks.

E92Fan · 01-03-2011, 06:32 PM

I don't think I have any OEM parts on my car anymore...

dzenno · 01-03-2011, 06:33 PM

Quote:

Originally Posted by E92Fan

I don't think I have any OEM parts on my car anymore...

Lol

tscdennab · 01-03-2011, 06:42 PM

Quote:

Originally Posted by gbreeE90

How do you damage the ECU cover?

And I have lost a few bolts, but thats it.

I broke a tiny plastic tab that was helping the open/close mechanism. I had to replace the cover, couldn't stand the thought...

onefastman · 01-03-2011, 07:10 PM

Tabs on the cabin air filter and lost bolts

Eyeman · 01-03-2011, 07:14 PM

I broke one of the tabs that you push with a small screwdriver to slip out one of the ECU connectors. It didn't seem to effect anything but as I was having other problems with my tune, etc at the time I thought I had really messed things up. I also messed up at least one, maybe two of the tabs for the wire harness holder. I guess it's good that I finally gave up on piggyback installing..lol.

Slidewayz · 01-03-2011, 08:49 PM

I sheared off a couple of bolts on the exhaust system. Cheap-a$$ German parts!!!

Forcefed3 · 01-03-2011, 08:55 PM

I intentionally cut the OEM front bumper shroud to fit my FMIC

Penn999 · 01-03-2011, 09:14 PM

Couple screws, tabs on the intake plastic piping, all the stuff you need to take off to get to the ecu...its all worn. I have literally been in my ecu 20-30 times and i have owned the car under a year(from switching tunes, to troubleshooting with shiv, learning to datalog...)

BTW, gbree I made a couple videos of my engine bay and exhaust today. Shoot me your email address again and I will send um to you

Forcefed3 · 01-03-2011, 09:19 PM

Quote:

Originally Posted by Penn999

Couple screws, tabs on the intake plastic piping, all the stuff you need to take off to get to the ecu...its all worn. I have literally been in my ecu 20-30 times and i have owned the car under a year(from switching tunes, to troubleshooting with shiv, learning to datalog...)

BTW, gbree I made a couple videos of my engine bay and exhaust today. Shoot me your email address again and I will send um to you

Thats a good many time you have opened the ECU!

Rotorocious · 01-03-2011, 10:08 PM

Broke a tab on that power wire holder that fits up underneath the cowl. Doesn't really fit anyway with my DCI's. Just hanging now

Tiago@VRSF · 01-03-2011, 10:48 PM

A nipple on the intake manifold broke when lightly pulling off the vacuum hose for the bov. That was very disappointing.

Penn999 · 01-03-2011, 11:20 PM

Quote:

Originally Posted by gbreeE90

Thats a good many time you have opened the ECU!

yeah, I can do that practically blindfolded now..

Forcefed3 · 01-03-2011, 11:45 PM

Quote:

Originally Posted by Penn999

Quote:

Originally Posted by gbreeE90

Thats a good many time you have opened the ECU!

yeah, I can do that practically blindfolded now..

I can get in the ecu very easily. I still have trouble sliding out the sub connectors.

hipnotic · 01-04-2011, 11:46 AM

only the grill tab

**335i** · 01-04-2011, 12:29 PM

none cos did almost nothing

bigdaddycane · 01-04-2011, 12:53 PM

last weekend while running my JB3 USB cable to the glove box I bump the little threaded tab for the ecu side bolt on the cowl.....it went under the ecu box..

..and I don't have a magnet tool.....pissed me off. Gotta borrow a magnet tool or pay .27 for a new part.

Penn999 · 01-04-2011, 01:37 PM

Quote:

Originally Posted by bigdaddycane

last weekend while running my JB3 USB cable to the glove box I bump the little threaded tab for the ecu side bolt on the cowl.....it went under the ecu box..

..and I don't have a magnet tool.....pissed me off. Gotta borrow a magnet tool or pay .27 for a new part.

LOL 27 cents...

Slidewayz · 01-04-2011, 01:47 PM

Oh, I forgot...don't know if this counts, but I also bent the handle and sheared off the tab on a 3/8" ratchet when tightening lug nuts on one of my wheels (didn't have the right sized lug wrench)...I guess that was enough torque

01-03-2011, 06:01 PM	#1
tscdennab Banned 162 Rep 1,809 Posts Drives: BMW 335i Join Date: Oct 2010 Location: Europe iTrader: (0) Garage List 2008 BMW [6.24]	How many OEM parts did you break while installing stuff in your car ? :) I have replaced an ECU cover and an air conditioning cowling until now, both damaged when trying to get the ECU out of the car...anyone else ?
	Appreciate 0 Tweet Quote

01-03-2011, 06:13 PM	#2
Forcefed3 Banned 136 Rep 4,732 Posts Drives: 2008 335i Join Date: May 2010 Location: South iTrader: (2) Garage List 2008 335i [1.00]	How do you damage the ECU cover? And I have lost a few bolts, but thats it.
	Appreciate 0 Quote

01-03-2011, 06:16 PM	#3
Dmacc Colonel 214 Rep 2,800 Posts Drives: 2011 BMW 1M Join Date: Mar 2010 Location: So Cal iTrader: (1)	I've lost two bolts for the air conditioning cover and I've snapped one of my connector pins for the ecu I had to sauder it back together, then file it down enough so it could fit back in the original pin hole, it barely fits __________________ thanks to MGallop
	Appreciate 0 Quote

01-03-2011, 06:32 PM	#5
E92Fan Moderator 344 Rep 5,493 Posts Drives: . Join Date: Aug 2007 Location: . iTrader: (0)	I don't think I have any OEM parts on my car anymore... __________________ ... ... ... DMS Remap Review ----- Quaife LSD Review ----- Hartge Antiroll Bars Review ----- Bilstein PSS10 B16 Ride Control Review ----- Detail by ShineOn ----- Paintshield Review
	Appreciate 0 Quote

01-03-2011, 07:10 PM	#8
onefastman Major General 167 Rep 5,689 Posts Drives: 2009 135i 2011 e92m dct Join Date: Sep 2009 Location: Earth iTrader: (15)	Tabs on the cabin air filter and lost bolts __________________ Legal Disclaimer: Anything I or anyone else says about my vehicle on this website(1addicts.com or any affiliated or nonaffiliated sites), pertaining to modifications, is only to gain acceptance from my/our peers, and does not actually represent anything actually existing on my car, and thus, cannot be held against me in any issues, i.e. warranty claims, that may arise.
	Appreciate 0 Quote

01-03-2011, 07:14 PM	#9
Eyeman Colonel 125 Rep 2,046 Posts Drives: 2008 135 blk, blk, step Join Date: Jan 2009 Location: Atlanta, GA iTrader: (0) Garage List 1994 Porsche 968 Cab [0.00] 2017 AMG GTS [0.00] 1994 Porsche 968 Coupe [0.00] 1977 Mercedes 450SE ... [0.00] 2008 135 [8.00]	I broke one of the tabs that you push with a small screwdriver to slip out one of the ECU connectors. It didn't seem to effect anything but as I was having other problems with my tune, etc at the time I thought I had really messed things up. I also messed up at least one, maybe two of the tabs for the wire harness holder. I guess it's good that I finally gave up on piggyback installing..lol. __________________ Injen, RR OCC, MadDad Whisper, donut spare, 19x8.5et43fr 19x9.5et45r Volk LE37's, rear fenders rolled/pulled, PSS4S 225/35fr 255/30r, KW V1's, AR coated catless dps, Cross strutbar, CF grills and license plate holder, iCarbon diffuser, ETS black anodized FMIC, M3 control arms, Quaife, ER chargepipe, ForgeDV's, Topspeed Custom Tune, V3sims, Braille, Andrey_GTA rear hub mod, Ebay Mstyle front bumper and performance style side skirts.
	Appreciate 0 Quote

01-03-2011, 08:49 PM	#10
Slidewayz Major 38 Rep 1,177 Posts Drives: 2007 335i Join Date: Jan 2009 Location: Oakland, CA iTrader: (5)	I sheared off a couple of bolts on the exhaust system. Cheap-a$$ German parts!!!
	Appreciate 0 Quote

01-03-2011, 08:55 PM	#11
Forcefed3 Banned 136 Rep 4,732 Posts Drives: 2008 335i Join Date: May 2010 Location: South iTrader: (2) Garage List 2008 335i [1.00]	I intentionally cut the OEM front bumper shroud to fit my FMIC
	Appreciate 0 Quote

01-03-2011, 09:14 PM	#12
Penn999 Lieutenant Colonel 55 Rep 1,661 Posts Drives: 335i coupe Join Date: May 2010 Location: VA iTrader: (3)	Couple screws, tabs on the intake plastic piping, all the stuff you need to take off to get to the ecu...its all worn. I have literally been in my ecu 20-30 times and i have owned the car under a year(from switching tunes, to troubleshooting with shiv, learning to datalog...) BTW, gbree I made a couple videos of my engine bay and exhaust today. Shoot me your email address again and I will send um to you __________________ 07' MT, Quaife LSD, BMW Performance LED Steering Wheel, HPF FMIC, AA BOV, HPF Exhaust, DCI, Procede V5, AR Stage 1 oil cooler, AR OCC, AR CL DP's, Vishnu Meth Kit, UUC SSK+DSSR, UUC Shift knob, (19 inch)VMR V715's/Yokohama Advan AD08's, Hartge Pedals and Floor Mats. Awaiting Install: M3 Rear Subframe Bushings, Full M3 suspension bits, AST 4100's, DSS axles. Future plans: Vishnu Single turbo kit
	Appreciate 0 Quote

01-03-2011, 10:08 PM	#14
Rotorocious Lieutenant Colonel 106 Rep 1,520 Posts Drives: 335xi Join Date: May 2010 Location: Colorado iTrader: (3)	Broke a tab on that power wire holder that fits up underneath the cowl. Doesn't really fit anyway with my DCI's. Just hanging now
	Appreciate 0 Quote

01-03-2011, 10:48 PM	#15
Tiago@VRSF 2126 Rep 43,349 Posts Drives: F90 M5 Join Date: Dec 2007 Location: Doral, FL iTrader: (99) Garage List 2014 F30 328xi [0.00] 2015 F82 BMW M4 [0.00] 2013 Ducati 1199 Pa ... [0.00] 2008 BMW 335i [0.00]	A nipple on the intake manifold broke when lightly pulling off the vacuum hose for the bov. That was very disappointing.
	Appreciate 0 Quote

01-04-2011, 11:46 AM	#18
hipnotic Major General 153 Rep 6,603 Posts Drives: e92 335i Join Date: Oct 2007 Location: So. Cal iTrader: (7) Garage List 2008 335i coupe [7.00]	only the grill tab
	Appreciate 0 Quote

01-04-2011, 12:29 PM	#19
335i Colonel 191 Rep 2,320 Posts Drives: TOYOTA & 2008 E92 335i 6MT Join Date: Jul 2007 Location: Swiss iTrader: (4) Garage List 2008 335i [9.00]	none cos did almost nothing __________________ E92 335i Black Saphire 6MT PROcede V5, BMS DCI, Big Tom IC, AR CL-DP's 3", AR Design OC, Forge DV's, OEM M3 side skirts, BMW Performance Wheels 19 inch 269 Black Gloss+Continental ContiSportContact 5P (400hp and 550nm) https://www.youtube.com/user/aistis7..._as=subscriber
	Appreciate 0 Quote

01-04-2011, 12:53 PM	#20
bigdaddycane I even mod my cereal 271 Rep 3,484 Posts Drives: 11 ZCP DCT M3 14 328d 21 GT4 Join Date: Aug 2009 Location: Northern Va iTrader: (53) Garage List 2021 Porsche GT4 [0.00] 2014 BMW 328d Xdriv ... [0.00] 2011 BMW M3 [0.00]	last weekend while running my JB3 USB cable to the glove box I bump the little threaded tab for the ecu side bolt on the cowl.....it went under the ecu box....and I don't have a magnet tool.....pissed me off. Gotta borrow a magnet tool or pay .27 for a new part. __________________ 2011 Mineral White M3 ZCP - Opticoat, Ventureshield, some CF, B&B exhaust, AFE Intake Vorsteiner VFF 101s Ohlins 2014 Mineral White 328d Xdrive Wagon - Opticoat, Ventureshield, B8s, H&R, Apex SM-10s Hawk Pads 2021 718 Cayman GT4 - Fire extinguiser, Neodyme GT3 Wheel Color
	Appreciate 0 Quote

01-04-2011, 01:47 PM	#22
Slidewayz Major 38 Rep 1,177 Posts Drives: 2007 335i Join Date: Jan 2009 Location: Oakland, CA iTrader: (5)	Oh, I forgot...don't know if this counts, but I also bent the handle and sheared off the tab on a 3/8" ratchet when tightening lug nuts on one of my wheels (didn't have the right sized lug wrench)...I guess that was enough torque
	Appreciate 0 Quote

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search