Bucking and Surging questions

clairvoyant · 03-22-2011, 10:21 AM

After upgrading to Procede V5, I start to experience bucking and surging when I drive on 1st or 2nd gear between 1500-2000 rpm.
Are there specific variables or parameters I need to change to eliminate bucking and surging?

-No CEL or engine malfunction recorded.
-The fuel injectors are fine (according to the dealer).
-DCI air filters are clean.

Thank You

enrita · 03-22-2011, 11:23 AM

which maps are you using and did you clear ALL adaptations basically followed the .doc guide included in the maps?

fisherbln · 03-22-2011, 12:11 PM

Have you been running NA mode at all? There is a known bug in NA mode that causes this if it is run for an extended period of time. It is on the list to fix, but the current recommendation is to only run NA mode for short periods of time.

OpenFlash · 03-22-2011, 12:35 PM

+1 on adaptation resets. And if you have a 6at, make sure you do the trans reset. It's not critical but most find that this solves any issue.

clairvoyant · 03-22-2011, 02:28 PM

It's not 6AT.
I have to be on the Mode 3 to be able to "reset the adaptation", right?
There are:
Command 3 - ECU Reset
Command 4 - Throttle Adaption Reset
Command 5 - Lambda Adaption Reset
Command 6 - AFR Adaption Reset
Command 7 - Battery Adaption Reset
Command 8 - Knock Adaption Reset
Command 9 - Octane Adaption Reset
Command 10 - VANOS Adaption Reset
Command 11 - VVT Adaption Reset

Which one do I reset to cure my bucking and surging issues?

Quote:

Originally Posted by shiv@vishnu

+1 on adaptation resets. And if you have a 6at, make sure you do the trans reset. It's not critical but most find that this solves any issue.

enrita · 03-22-2011, 02:32 PM

Quote:

Originally Posted by clairvoyant

It's not 6AT.
I have to be on the Mode 3 to be able to "reset the adaptation", right?
There are:
Command 3 - ECU Reset
Command 4 - Throttle Adaption Reset
Command 5 - Lambda Adaption Reset
Command 6 - AFR Adaption Reset
Command 7 - Battery Adaption Reset
Command 8 - Knock Adaption Reset
Command 9 - Octane Adaption Reset
Command 10 - VANOS Adaption Reset
Command 11 - VVT Adaption Reset

Which one do I reset to cure my bucking and surging issues?

yes mode 3 , go through 11-1

clairvoyant · 03-22-2011, 02:39 PM

11-1????

Quote:

Originally Posted by enrita

yes mode 3 , go through 11-1

wren57 · 03-22-2011, 02:40 PM

Yes, do all the resets from 11 down to 1.

clairvoyant · 03-22-2011, 08:07 PM

Can you reset all of them via a laptop?
A better question: Is there one button reset them all trick (without the laptop)?
Thank You

Quote:

Originally Posted by wren57

Yes, do all the resets from 11 down to 1.

wren57 · 03-22-2011, 08:11 PM

A laptop is not necessary to reset them. You do it through the procede command center. It takes literally 10 seconds to reset them all individually.

read here:
http://www.e90post.com/forums/showthread.php?t=464460

and watch:

Iwantm3 · 03-22-2011, 08:15 PM

11-1 ? I thought 11-3

wren57 · 03-22-2011, 08:25 PM

1 and 2 just read and clear any DME codes.

cn555ic · 03-22-2011, 08:28 PM

Quote:

Originally Posted by Iwantm3

11-1 ? I thought 11-3

Mike just try out the new maps it should fix your misfire issue that you had...These maps are awesome and themyst has beaten the crap out of his car and nothing...no more issues!

Iwantm3 · 03-22-2011, 08:40 PM

Quote:

Originally Posted by cn555ic

Mike just try out the new maps it should fix your misfire issue that you had...These maps are awesome and themyst has beaten the crap out of his car and nothing...no more issues!

Yeah I had them before they were even released here lol , my car is having some other issues but I don't think it's tune related. I can't wait to finish my fKen meth kit already , I miss it lol. BTW I got some LOUD ASS eisenmann mufflers I told you about lol you HAVE to check them out, INSANE lol

clairvoyant · 03-23-2011, 08:18 AM

Even after upgrading to the newest firmware and the map, I still need to reset those adaptations, don't I?

enrita · 03-23-2011, 09:09 AM

Quote:

Originally Posted by clairvoyant

Even after upgrading to the newest firmware and the map, I still need to reset those adaptations, don't I?

Yes ... read the doc included that tells you how to do the update.

zerep1 · 03-23-2011, 10:07 AM

thats all the poweerrrrrrrrr ripping holes in the pavement

03-22-2011, 10:21 AM	#1
clairvoyant Major 88 Rep 1,032 Posts Drives: Bavarian Manure Wagon (BMW) Join Date: Oct 2007 Location: 45°19′20″N, 75°50′0″W iTrader: (5) Garage List 2007 335i [5.24]	Bucking and Surging questions After upgrading to Procede V5, I start to experience bucking and surging when I drive on 1st or 2nd gear between 1500-2000 rpm. Are there specific variables or parameters I need to change to eliminate bucking and surging? -No CEL or engine malfunction recorded. -The fuel injectors are fine (according to the dealer). -DCI air filters are clean. Thank You
	Appreciate 0 Tweet Quote

03-22-2011, 11:23 AM	#2
enrita Major General 165 Rep 7,377 Posts Drives: 335i - Big turbos Join Date: Sep 2008 Location: Italian in Sweden iTrader: (0)	which maps are you using and did you clear ALL adaptations basically followed the .doc guide included in the maps? __________________ 07 335i AT - MOTIV 750 - MHD E85 BMS flash - BMS PI - JB4G5 - Okada Coils - NGK 5992 Plugs - Helix IC - Snow Stg. 3 - Stett CP - Custom midpipes with 100 HJS Cats - Bastuck Quad - PSS10 - QUAIFE LSD - BMS OCC - Forge DVs - AR OC - ALCON BBK - M3 Chassi - Dinan CP - Velocity M rear Toe arms - Advan RZ-DF - LUX H8 - Level 10 AT upgrade
	Appreciate 0 Quote

03-22-2011, 12:11 PM	#3
fisherbln Captain 12 Rep 859 Posts Drives: 2007 335i Coupe Join Date: Sep 2009 Location: USA iTrader: (2)	Have you been running NA mode at all? There is a known bug in NA mode that causes this if it is run for an extended period of time. It is on the list to fix, but the current recommendation is to only run NA mode for short periods of time. __________________ 2007 335i SG Coupe 2009 128i AW
	Appreciate 0 Quote

03-22-2011, 12:35 PM	#4
OpenFlash 1849 Rep 17,960 Posts Drives: A Lot Join Date: Sep 2006 Location: SF Bay, CA iTrader: (0) Garage List 2018 Ducati Panigal ... [0.00] 2016 Mazda CX5 [0.00] 2017 Aprilia Tuono ... [0.00] 2019 BMW M2 Competi ... [0.00] 2015 BMW M5 Competi ... [10.00] 2016 Ducati XDiavel S [0.00] 2016 AMG GT S [0.00] 2011 Ferrari 458 It ... [0.00] 2017 Charger Hellcat [0.00] 2015 KTM Super Duke ... [0.00] 2016 KTM RC390 [0.00]	+1 on adaptation resets. And if you have a 6at, make sure you do the trans reset. It's not critical but most find that this solves any issue.
	Appreciate 0 Quote

03-22-2011, 02:40 PM	#8
wren57 Roll Tide 615 Rep 2,366 Posts Drives: 335i Join Date: Jul 2010 Location: St Louis iTrader: (10)	Yes, do all the resets from 11 down to 1. __________________ Fix your broken/stripped cowl bolts with this elegant brass solution! http://www.e90post.com/forums/showthread.php?p=20230306
	Appreciate 0 Quote

03-22-2011, 08:11 PM	#10
wren57 Roll Tide 615 Rep 2,366 Posts Drives: 335i Join Date: Jul 2010 Location: St Louis iTrader: (10)	A laptop is not necessary to reset them. You do it through the procede command center. It takes literally 10 seconds to reset them all individually. read here: http://www.e90post.com/forums/showthread.php?t=464460 and watch: __________________ Fix your broken/stripped cowl bolts with this elegant brass solution! http://www.e90post.com/forums/showthread.php?p=20230306
	Appreciate 0 Quote

03-22-2011, 08:15 PM	#11
Iwantm3 Banned 40 Rep 1,284 Posts Drives: 335i M sport Join Date: Mar 2009 Location: US AND A I likeeeee iTrader: (1)	11-1 ? I thought 11-3
	Appreciate 0 Quote

03-22-2011, 08:25 PM	#12
wren57 Roll Tide 615 Rep 2,366 Posts Drives: 335i Join Date: Jul 2010 Location: St Louis iTrader: (10)	1 and 2 just read and clear any DME codes. __________________ Fix your broken/stripped cowl bolts with this elegant brass solution! http://www.e90post.com/forums/showthread.php?p=20230306
	Appreciate 0 Quote

03-23-2011, 08:18 AM	#15
clairvoyant Major 88 Rep 1,032 Posts Drives: Bavarian Manure Wagon (BMW) Join Date: Oct 2007 Location: 45°19′20″N, 75°50′0″W iTrader: (5) Garage List 2007 335i [5.24]	Even after upgrading to the newest firmware and the map, I still need to reset those adaptations, don't I?
	Appreciate 0 Quote

03-23-2011, 10:07 AM	#17
zerep1 Lieutenant 40 Rep 464 Posts Drives: 335i E90, 328i F30, 230i G42, Join Date: Nov 2010 Location: Tampa, Florida iTrader: (1)	thats all the poweerrrrrrrrr ripping holes in the pavement
	Appreciate 0 Quote

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search