Procede V5 NA map..Shiv

caliguy562 · 05-24-2011, 02:23 PM

Will the NA map ever be a reality or is it just one of those things that's plagued with adaptation nightmares? The sound of running with open wastegates even on a stock exhaust was intoxicating.

enrita · 05-24-2011, 02:29 PM

just set your wg value to 30% for the sound...

Jeff@TopGearSolutions · 05-24-2011, 02:46 PM

Quote:

Originally Posted by enrita

just set your wg value to 30% for the sound...

Are there any negatives to doing that? Performance wise?

caliguy562 · 05-24-2011, 02:54 PM

I thought I read somewhere to only adjust if the wastegates were rattling. I've thought about just adjusting the value. However, I would have to drag the computer out everytime I wanted to tame things down again. It was convenient being able to just pull a few times on the stalk.

OpenFlash · 05-24-2011, 03:00 PM

Quote:

Originally Posted by enrita

just set your wg value to 30% for the sound...

+1

No downsides other than the fraction of a second needed for the wastegates to go from full open to closed (to build boost) when called upon. Barely noticeable.

caliguy562 · 05-24-2011, 03:10 PM

Hmm, guess I'll have to play around with that value then. Thanks for taking the time to answer my question. Now back to those meth kits. I'm waiting patiently to be charged the other half for my kit. :-)

Syndicategt · 05-24-2011, 03:31 PM

Quote:

Originally Posted by Jeff@topgearsolutions

Are there any negatives to doing that? Performance wise?

Yea, lots of drone! I have to do it because my WG's rattle like crazy when at 90%.

TwinTurboXI · 05-24-2011, 05:54 PM

Quote:

Originally Posted by caliguy562

Will the NA map ever be a reality or is it just one of those things that's plagued with adaptation nightmares? The sound of running with open wastegates even on a stock exhaust was intoxicating.

Care to elaborate more on the adaptation nightmares?

So I should never run the NA mode?

Joe@TopGearSolutions · 05-24-2011, 05:55 PM

You should not be using N/A mode on the current maps last I recall

JO3 · 05-24-2011, 06:53 PM

There was a post on here a while back about how it was ok to use NA mode as long as it was stop and go, and not steady cruising. ymmv

I've been tinkering with my WG values, since I was getting a little rattle at idle with 90%. I tried 30%, but it was too loud for me. So I tried 50%, and that got rid of the rattle at idle, but then i got a rattle during moderate acceleration (which was way more annoying). I'm guessing that at the onset of making boost, as the wastegates are closing or near close, that's where I would get the rattle. So then I tried 100%, and the rattle at idle is quieter, and no more rattle while accelerating. But I haven't heard of anyone running at 100%. Anyone try it? Are there any downsides?

OpenFlash · 05-24-2011, 06:55 PM

Quote:

Originally Posted by JO3

There was a post on here a while back about how it was ok to use NA mode as long as it was stop and go, and not steady cruising. ymmv

I've been tinkering with my WG values, since I was getting a little rattle at idle with 90%. I tried 30%, but it was too loud for me. So I tried 50%, and that got rid of the rattle at idle, but then i got a rattle during moderate acceleration (which was way more annoying). I'm guessing that at the onset of making boost, as the wastegates are closing or near close, that's where I would get the rattle. So then I tried 100%, and the rattle at idle is quieter, and no more rattle while accelerating. But I haven't heard of anyone running at 100%. Anyone try it? Are there any downsides?

No downsides to running 100% wastegate position. Just use whatever works for you. Or better yet, tighten the wastegate actuators to get rid of the rattle

JO3 · 05-24-2011, 07:17 PM

Quote:

Originally Posted by shiv@vishnu

No downsides to running 100% wastegate position. Just use whatever works for you. Or better yet, tighten the wastegate actuators to get rid of the rattle

I know, but after re-installing my DPs for the fourth time (after a service visit), I've been too lazy to get back under the car, lol.

On a side note, I love how making this adjustment with the user settings is even a possibility. Procede FTW!

Sorry for the thread jack

caliguy562 · 05-24-2011, 07:42 PM

Quote:

Originally Posted by TwinTurboXI

Care to elaborate more on the adaptation nightmares?

So I should never run the NA mode?

On the 12/17 map I drove approx 160 miles straight from Santa Maria to Los Angeles on the NA map. I eventually switched to map 1 and developed some hesitation on hard 2nd and 3rd gear runs. These issues eventually worked themselves out. It felt like misfires, but I never got a code.

05-24-2011, 02:23 PM	#1
caliguy562 Lieutenant 8 Rep 476 Posts Drives: E92 335i Join Date: Dec 2007 Location: garaged somewhere in soCal iTrader: (3)	Procede V5 NA map..Shiv Will the NA map ever be a reality or is it just one of those things that's plagued with adaptation nightmares? The sound of running with open wastegates even on a stock exhaust was intoxicating.
	Appreciate 0 Tweet Quote

05-24-2011, 02:29 PM	#2
enrita Major General 161 Rep 7,377 Posts Drives: 335i - Big turbos Join Date: Sep 2008 Location: Italian in Sweden iTrader: (0)	just set your wg value to 30% for the sound... __________________ 07 335i AT - MOTIV 750 - MHD E85 BMS flash - BMS PI - JB4G5 - Okada Coils - NGK 5992 Plugs - Helix IC - Snow Stg. 3 - Stett CP - Custom midpipes with 100 HJS Cats - Bastuck Quad - PSS10 - QUAIFE LSD - BMS OCC - Forge DVs - AR OC - ALCON BBK - M3 Chassi - Dinan CP - Velocity M rear Toe arms - Advan RZ-DF - LUX H8 - Level 10 AT upgrade
	Appreciate 0 Quote

05-24-2011, 02:54 PM	#4
caliguy562 Lieutenant 8 Rep 476 Posts Drives: E92 335i Join Date: Dec 2007 Location: garaged somewhere in soCal iTrader: (3)	I thought I read somewhere to only adjust if the wastegates were rattling. I've thought about just adjusting the value. However, I would have to drag the computer out everytime I wanted to tame things down again. It was convenient being able to just pull a few times on the stalk.
	Appreciate 0 Quote

05-24-2011, 03:10 PM	#6
caliguy562 Lieutenant 8 Rep 476 Posts Drives: E92 335i Join Date: Dec 2007 Location: garaged somewhere in soCal iTrader: (3)	Hmm, guess I'll have to play around with that value then. Thanks for taking the time to answer my question. Now back to those meth kits. I'm waiting patiently to be charged the other half for my kit. :-)
	Appreciate 0 Quote

05-24-2011, 05:55 PM	#9
Joe@TopGearSolutions Major 267 Rep 1,173 Posts Drives: BMW Join Date: Mar 2011 Location: USA iTrader: (3)	You should not be using N/A mode on the current maps last I recall
	Appreciate 0 Quote

05-24-2011, 06:53 PM	#10
JO3 Lieutenant 14 Rep 566 Posts Drives: a lot Join Date: Mar 2006 Location: CA iTrader: (8)	There was a post on here a while back about how it was ok to use NA mode as long as it was stop and go, and not steady cruising. ymmv I've been tinkering with my WG values, since I was getting a little rattle at idle with 90%. I tried 30%, but it was too loud for me. So I tried 50%, and that got rid of the rattle at idle, but then i got a rattle during moderate acceleration (which was way more annoying). I'm guessing that at the onset of making boost, as the wastegates are closing or near close, that's where I would get the rattle. So then I tried 100%, and the rattle at idle is quieter, and no more rattle while accelerating. But I haven't heard of anyone running at 100%. Anyone try it? Are there any downsides?
	Appreciate 0 Quote

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search