[silvermist99]

Hello,

Is it possible to code out PDC? I had PDC on my original bumper and swapped out to non pdc mtech. It throws this error message on dashboard & idrive everytime I put the car in reverse, kind of annoying. I don't see any pdc related codes on the spreadsheet, any ideas? Only my 4 sensors are removed, module is still there

[ram33]

could you pull the fuse?

[Bender1012]

You need to remove PDC from your VO. It's not like coding other functions you're probably used to, but it's easy enough and also done with NCS. You'll need to find a list of VO codes and a guide for how to change VO. Let us know if you need more help.

[stratplaya06]

If the bumper is OEM there should be markings on the inside that show where to drill for perfect PDC fit, why not just reuse your old sensors and retain the PDC?

[silvermist99]

Originally Posted by stratplaya06

If the bumper is OEM there should be markings on the inside that show where to drill for perfect PDC fit, why not just reuse your old sensors and retain the PDC?

PDC is gone I gave it away with the bumper swap.

I'll eventually order new ones from ebay and re-connect them.

I'll take a look at the VO. Thanks

[JayTdotP]

Did anyone find a way to code out the Rear PDC's on an 2007 e92 ... Im upgrading to a Replica Mtech rear bumper that has no Pdc holes.. and im not getting paint work done just a wrap. So i wont have pdc holes.

[Elliott@DetailAddict]

I believe $508 is PDC.
So removing $508 for the VO and recoding the car should do the trick.

[JayTdotP]

Originally Posted by Grant@DetailAddict

I believe $508 is PDC.
So removing $508 for the VO and recoding the car should do the trick.

Hey im still wondering how to code out the PDC. i couldnt find the VO module, on my early build 2007 e92

[Elliott@DetailAddict]

It's the Enter FA button in NCS

[Bobf31]

The VO code for just rear PDC is $507, for front and rear it is $508.
But I believe it will generate the warnings as long as there is the steering device for front and rear.

I made the upgrade from only rear to front and rear and as soon as I connected the new steering unit without coding it gave me the warning about the PDC sensors.

[dcay]

I know this thread is old but a pdc module and camera in my daughter’s 2009 328i to get reverse camera capability for her. I have the sensors but did not want to actually install them. Seems like everything can be controlled with software so CAN THE PDC SENSOR WARNING BE CODED OUT and still keep the reverse camera function?

DCAY

[sdbmwcoding]

Originally Posted by dcay

I know this thread is old but a pdc module and camera in my daughter’s 2009 328i to get reverse camera capability for her. I have the sensors but did not want to actually install them. Seems like everything can be controlled with software so CAN THE PDC SENSOR WARNING BE CODED OUT and still keep the reverse camera function?

DCAY

You do not need pdc for reverse camera retrofit. But to answer your question, no. You'd need to disconnect the PDC module to remove any PDC malfunction warning

[penfold2105]

Hi guys I would like to say I messed up. Iv been trying to reset my CIC as the vin is different to the car. I followed this

however now I have a problem with the PDC. It decides to not come on when you put it in reverse for a few seconds, then shows its touching the car behind but in reality it's still 40 cm away. Anyone know how I can sort this.

[penfold2105]

Originally Posted by penfold2105

Hi guys I would like to say I messed up. Iv been trying to reset my CIC as the vin is different to the car. I followed this

however now I have a problem with the PDC. It decides to not come on when you put it in reverse for a few seconds, then shows its touching the car behind but in reality it's still 40 cm away. Anyone know how I can sort this.

Fixed it 😊

Just upgraded it in winkfp then restored to factory in NCS. Happy with myself starting to fix something rather than break it. 🤣