[FRMTL2_335i]

so i just got in the mail my relay with wires from Burger Motorsports to install the 2 step in my 07 335i m/t. but i can't seem to find the instructions on how to do it. they dont have a dyi in their website for the 2 step. can someone help me?

[Jeff@TopGearSolutions]

Just do 1 step at a time

Basic directions for connecting 2STEP/CLUTCH wire:

1) Locate green power connector, open bottom flap, and remove #8 orange wire. Place 2STEP relay red wire in its place. Connect #8 orange wire you removed to the 2STEP relay blue/white wire using preinstalled connector.
2) Put green power connector back in its location with relay hanging below or next to it.
3) Connect 2STEP black, which will have a wire nut connecting to an extension wire, in to the USB cable position #7.
4) For the NLS to work you must also install a clutch wire. Connect this to USB cable position #8.
5) Connect the male/female end of the clutch wire in to the gray DME connector position #18 as read from the female end. Either by removing the PNP connector and extracting that jumper wire, or simply removing the wire, sticking the female end in, connecting the OEM female wire in the new male pin, and folding a piece of tape in half over it. The wire needs to read the clutch signal.
6) To enable NLS you must set FutureUseE (previously bogfix) set to 0. NLS will cut engine power when pressing the clutch while gas is fully pressed and restore it when you let the clutch back out again. Practice doing full throttle runs at lower RPM to get the hang of it. When you press the clutch in while the gas is 100% down the RPM should drop like a rock. If they don't, you've botched the install.
7) Note if the car cranks without starting after installing the relay something is likely wired wrong. If you are unable to sort it out just email in install photos for support.

[FRMTL2_335i]

Originally Posted by Jeff@TopGearSolutions

Just do 1 step at a time

Basic directions for connecting 2STEP/CLUTCH wire:

1) Locate green power connector, open bottom flap, and remove #8 orange wire. Place 2STEP relay red wire in its place. Connect #8 orange wire you removed to the 2STEP relay blue/white wire using preinstalled connector.
2) Put green power connector back in its location with relay hanging below or next to it.
3) Connect 2STEP black, which will have a wire nut connecting to an extension wire, in to the USB cable position #7.
4) For the NLS to work you must also install a clutch wire. Connect this to USB cable position #8.
5) Connect the male/female end of the clutch wire in to the gray DME connector position #18 as read from the female end. Either by removing the PNP connector and extracting that jumper wire, or simply removing the wire, sticking the female end in, connecting the OEM female wire in the new male pin, and folding a piece of tape in half over it. The wire needs to read the clutch signal.
6) To enable NLS you must set FutureUseE (previously bogfix) set to 0. NLS will cut engine power when pressing the clutch while gas is fully pressed and restore it when you let the clutch back out again. Practice doing full throttle runs at lower RPM to get the hang of it. When you press the clutch in while the gas is 100% down the RPM should drop like a rock. If they don't, you've botched the install.
7) Note if the car cranks without starting after installing the relay something is likely wired wrong. If you are unable to sort it out just email in install photos for support.

oh i didnt think of that!.... im gonna try that next! thanks

[marv85]

should be pretty simple once you follow above... have fun

[cwarren]

cant tell you how many people I have walked through this .prob 10 by now .
almost made a complete diy w pic and all but lost the pic's with my old computer lol . last guy I drew a diagram took a picture from my phone and sent to him lol since I no longer run jb .not sure why so many have trouble with this.

[marv85]

Originally Posted by cwarren

cant tell you how many people I have walked through this .prob 10 by now .
almost made a complete diy w pic and all but lost the pic's with my old computer lol . last guy I drew a diagram took a picture from my phone and sent to him lol since I no longer run jb .not sure why so many have trouble with this.

you hsould remove G5 from your drives section on the left now that you're protuned and all

I need to drop by soon for a ride. I'm thinking about an intercooler lol

[FRMTL2_335i]

what is USB cable position #7 and #8
thats where i get lost.
does anyone have a picture of it?

[FRMTL2_335i]

im pretty much lost between step 3 n 6
5) Connect the male/female end of the clutch wire in to the gray DME connector position #18 as read from the female end. Either by removing the PNP connector and extracting that jumper wire, or simply removing the wire, sticking the female end in, connecting the OEM female wire in the new male pin, and folding a piece of tape in half over it. The wire needs to read the clutch signal.
6) To enable NLS you must set FutureUseE (previously bogfix) set to 0.


which one is the clutch signal wire? is it located by the pedal? if so im sure there is at least two wires there for that sensor, which one do i tap???

[FRMTL2_335i]

anyone?

[danmandle]

I came across this post after google-ing for the answer as well. There's a write-up here: http://www.e90post.com/forums/showthread.php?t=874651

Note, follow the diagram, not the instructions. At the time of writing this, the wires on the USB cable were backwards.

[cwarren]

lmao that's the diagram I drew up glad this helped out some people..

[FRMTL2_335i]

Originally Posted by cwarren

lmao that's the diagram I drew up glad this helped out some people..

It did, I even passed it along to a few people after you helped me out!!!

[cwarren]

that right didn't you send me a clip of the car shooting flames out the exhaust !

[FRMTL2_335i]

Originally Posted by cwarren

that right didn't you send me a clip of the car shooting flames out the exhaust !

YES that was me!!!

[Marc335i]

Originally Posted by FRMTL2_335i

YES that was me!!!

What mods do you have for the flames?? Sick af man!!

[ThaiRacer]

Did any1 have to activate on the laptop I bought my jb4 premiered with the relay from bms and installed and my 2 step isn't working