[RLNY]

Ok I just installed the g5 ISO and I was trying to set the toggle switch for the gauge sweep and I don't know if I pressed something else accidentally but all the guages just started to be off. I mean like when u first turn it on with the down volume button and the other button and the go from 0 to 1. Instead of going to 1 it goes from 0 to a few notches before 1 then in between 2 and 3, the it goes to the notch in between 3 and 4 etc. it doss not act normally by going from 0,1,2,3 etc. now before all this everything was normal. I installed g5 and the guages we're perfect. what the hell press to make it do this? I reset the guages but it still does the same thing. How do I get it back to normal. Sorry for the sloppy writing.

[DuDai]

Try speedo on 10 and tach on 5. That one should reset the cluster. Should get your gauges back in alignment.

[RLNY]

Originally Posted by DuDai

Try speedo on 10 and tach on 5. That one should reset the cluster. Should get your gauges back in alignment.

Tried that and it doesn't work

[DuDai]

Try 50 on speedo, then 2 on the tach fly imperial gauges, and 50/3 for metric gauges depending on your cluster. See if that helps.

[Jhe]

Try speedo 5 tach 2.

[mike@x-ph.com]

Originally Posted by RLNY

Ok I just installed the g5 ISO and I was trying to set the toggle switch for the gauge sweep and I don't know if I pressed something else accidentally but all the guages just started to be off. I mean like when u first turn it on with the down volume button and the other button and the go from 0 to 1. Instead of going to 1 it goes from 0 to a few notches before 1 then in between 2 and 3, the it goes to the notch in between 3 and 4 etc. it doss not act normally by going from 0,1,2,3 etc. now before all this everything was normal. I installed g5 and the guages we're perfect. what the hell press to make it do this? I reset the guages but it still does the same thing. How do I get it back to normal. Sorry for the sloppy writing.

Send an email to Terry

[foreignmuscle]

Originally Posted by RLNY

Ok I just installed the g5 ISO and I was trying to set the toggle switch for the gauge sweep and I don't know if I pressed something else accidentally but all the guages just started to be off. I mean like when u first turn it on with the down volume button and the other button and the go from 0 to 1. Instead of going to 1 it goes from 0 to a few notches before 1 then in between 2 and 3, the it goes to the notch in between 3 and 4 etc. it doss not act normally by going from 0,1,2,3 etc. now before all this everything was normal. I installed g5 and the guages we're perfect. what the hell press to make it do this? I reset the guages but it still does the same thing. How do I get it back to normal. Sorry for the sloppy writing.

Did you ever figure it out ??

[Fvllsxnd.e90]

Yes, did you ever get an answer to this and how do I send an email to Terry? I’ve had a a jb4 on my car for a couple weeks now I’m loving it but tonight I was looking at it trying to enable the one touch DTC option for start up as well as some other things not only does it seem like none of my selections are saving, but my gauges are not working correctly. It started with my fuel gauge was not functioning at all and I did the reset cluster and then I noticed that when I go into the selection menu for the Maps, it starts at 00 but if I go to zero one it’s actually above the one and then when I go to two it’s in between two and three. And so on until four map, seven and eight is actually touching the oil temperature gauge and on start up it seems like my rpm is not showing correctly

[dmckmc]

Try JB4 support site: https://www.jb4tech.com/