[LACA335i]

I dont know if it is a repost or not.. i was checking out Dinan website out today.. They came out all of the suspension stuffs... Price are outragiously insame if u asking me.. Too bad they dont tuning out ecm or do something else beside suspension

http://www.dinanbmw.com/

[stressdoc]

Where on the site is it?

[RichP]

Probably just carry-over parts from the other E9x cars...

Im waiting for their xede that cost $7K

[LACA335i]

Originally Posted by stressdoc

Where on the site is it?

http://www.dinanbmw.com/ under product select e90 / 335 Sedan (E90) 2007

Camber Plates
Chassis Tuning

Part #:

Price:
D160-0002
$249.00

Labor Hours: 3.50


Dinan Camber Plates provide 0.5 degrees more negative camber on the front wheels. The additional negative camber provides more grip in the turns reducing the vehicle's tendency to plow the front end for those who drive a bit more aggressively. The camber plates also provide additional clearance, allowing you to fit larger tires (see Dinan's 19" Lightweight Wheel Package and related tire size information.




Click here for printable version of this product back to top

19" Lightweight Wheel Set (Front and Rear Package)
Chassis Tuning

Part #:

Price:
D750-0001A
$5299.00

List of Included Items: 2 ea. 19 x 9" Front Wheels; Front Wheel Spacers/Lug Bolt Set; 2 ea. 19 x 9.5" Rear Wheels.
Special Notes: Recommended Tire Sizes: Front-245/30-19; Rear-265/30-19*
Point Value: 5



Developed specifically for the E90 3 Series, Dinan's 19" forged wheels are the lightest available and allow you to fit the largest tires possible for maximum grip and reduction of understeer. And, of course, the look is nothing short of stunning with the large tires and wheels filling up the generous fender wells.

The 19" diameter enables you to install the Dinan by Brembo brakes as well, offering adequate clearance for the large calipers and rotors.

The rear wheels measure 9.5" wide, accommodating 265/30-19 tires. The front wheels measure 9" wide, accommodating 245/30-19s. In addition to the dramatically improved grip provided by the wider front and rear tires, the wheels substantially reduce unsprung weight with the 19 x 9.5s weighing in at a mere 20 lbs., compared to the stock 18 x 8.5" wheel at 26 lbs. The combination of the Dinan wheels and high performance tires (non-run flats), reduces unsprung mass by an astounding 51 lbs., improving not only acceleration, braking, and handling, but ride quality as well. The substantial increase in front tire width dramatically reduces understeer for turn-in that is precise and predictable.

The wheels might well be considered a work of art. Each and every surface of the forged wheel is machined, eliminating uneccessary material for the lightest possible weight. The elegant design adds an even more aggressive flavor to the new 3 Series, while maintaining a look that is very much in keeping with the cars' styling. The open design also makes them quite easy to rid of that pesky brake dust as well.


Features and Benefits
Spread Forged Construction-
Superior strength while keeping weight to an absolute minimum.

The Lightest 19" Wheels Available-
At just 20 lbs., the Dinan wheels are over 6 lbs. lighter than the next closest competitive wheel we've found.

Reduces Unsprung Weight by 51 lbs. (including tires)-
This dramatic reduction of unsprung weight improves acceleration, handling, braking, and ride quality.

Dinan Wheels Fit the Largest Tires Possible-
The Dinan wheels have been designed to allow fitment of the widest tires possible for maximum grip*.

Reduced Understeer/Improved Turn-In-
The increase in front tire width provides more grip in the corners, reducing the cars' characteristic understeer for turn-in that is razor sharp.


*The Dinan E90 3 Series wheels will accommodate 275/30 rear and 255/30-19 front tires when front camber plates are installed, providing the necessary clearance for the larger front tires.

Please note that the physical dimensions of different tire manufacturer’s products vary for a given tire size designation (i.e. 285/30-19). This can be true even within the same manufacturer’s product line, where one tire “model” may be taller or wider than another model, even though the size designation is the same. As a result, it may be necessary to modify the wheel well and/or fender lip if the selected tire size differs substantially from the specific manufacturers’ tire models tested by Dinan. Conversely, it may be possible to fit a larger tire size designation than that specified by Dinan if the selected tire runs smaller than the “standard”.

Click here for printable version of this product back to top

Dinan/Brembo Front & Rear Brake Conversion-Black
Chassis Tuning

Part #:

Price:
D290-0906-B
$6390.00

Labor Hours: 5.50
Required Products: 19" or larger wheels.
Point Value: 3



Dinan Performance Brakes by Brembo are now available for E90 335i applications providing the driving enthusiast with ultimate stopping power for the street, as well as track events. Extensive testing has enabled us to develop custom systems that have been tuned for optimum performance, while avoiding the foibles of typical “big brake kits”, such as unbalanced proportioning, poor pedal feel and unacceptable noise levels, just to name a few. The brake calipers are available in either red or black, giving you the choice of a stealth or competition look.









The Dinan/Brembo Four-Wheel Brake Conversion Features:
Front Rotors: 380mm Slotted with Aluminum Hats (Stock Rotors Measure 348mm)
Rear Rotors: 345mm Slotted with Aluminum Hats (Stock Rotors Measure 336mm)
Calipers: 4-Piston, Aluminum (Available in Black or Red)
Goodridge DOT/TUV Approved Stainless Steel Brake Lines
Mounting Brackets and Assembly Hardware
Dinan-spec Ferodo Brake Pads with Sensor Provision

In most cases, the large rotors and calipers will require the use of aftermarket wheels for adequate brake clearance. Dinan’s soon to be released 19" lightweight performance wheels are recommended, providing proper clearance and the ability to fit the largest tires possible for optimum performance. Be sure to check with the manufacturer or distributor of the wheels you are considering in order to verify that they offer the necessary clearance, citing the Brembo “Gran Turismo” brakes as a reference. A fitment guide, including templates for the various applications, is available by clicking on the link below or you may select "Technical/Forms" from the navigation bar above, then select "Miscellaneous".
Brembo_Caliper_Templates.pdf







Click here for printable version of this product back to top

Dinan/Brembo Front & Rear Brake Conversion-Red
Chassis Tuning

Part #:

Price:
D290-0906-R
$6390.00

Labor Hours: 5.50
Required Products: 19" or larger wheels.
Point Value: 3



Dinan Performance Brakes by Brembo are now available for E90 335i applications providing the driving enthusiast with ultimate stopping power for the street, as well as track events. Extensive testing has enabled us to develop custom systems that have been tuned for optimum performance, while avoiding the foibles of typical “big brake kits”, such as unbalanced proportioning, poor pedal feel and unacceptable noise levels, just to name a few. The brake calipers are available in either red or black, giving you the choice of a stealth or competition look.









The Dinan/Brembo Four-Wheel Brake Conversion Features:
Front Rotors: 380mm Slotted with Aluminum Hats (Stock Rotors Measure 348mm)
Rear Rotors: 345mm Slotted with Aluminum Hats (Stock Rotors Measure 336mm)
Calipers: 4-Piston, Aluminum (Available in Black or Red)
Goodridge DOT/TUV Approved Stainless Steel Brake Lines
Mounting Brackets and Assembly Hardware
Dinan-spec Ferodo Brake Pads with Sensor Provision

In most cases, the large rotors and calipers will require the use of aftermarket wheels for adequate brake clearance. Dinan’s soon to be released 19" lightweight performance wheels are recommended, providing proper clearance and the ability to fit the largest tires possible for optimum performance. Be sure to check with the manufacturer or distributor of the wheels you are considering in order to verify that they offer the necessary clearance, citing the Brembo “Gran Turismo” brakes as a reference. A fitment guide, including templates for the various applications, is available by clicking on the link below or you may select "Technical/Forms" from the navigation bar above, then select "Miscellaneous".
Brembo_Caliper_Templates.pdf




Click here for printable version of this product back to top

Dinan/Brembo Front Brake Conversion-Black
Chassis Tuning

Part #:

Price:
D290-0905-B
$3595.00

Labor Hours: 2.80
Required Products: 18" or larger wheels.
Point Value: 3


Dinan Performance Brakes by Brembo are now available for E90 335i applications providing the driving enthusiast with ultimate stopping power for the street, as well as track events. Extensive testing has enabled us to develop custom systems that have been tuned for optimum performance, while avoiding the foibles of typical “big brake kits”, such as unbalanced proportioning, poor pedal feel and unacceptable noise levels, just to name a few. The brake calipers are available in either red or black, giving you the choice of a stealth or competition look.





The Dinan/Brembo Front Brake Conversion Features:
Front Rotors: 380mm Slotted with Aluminum Hats (Stock Rotors Measure 348mm)
Calipers: 4-Piston, Aluminum (Available in Black or Red)
Goodridge DOT/TUV Approved Stainless Steel Brake Lines
Mounting Brackets and Assembly Hardware
Dinan-spec Ferodo Brake Pads with Sensor Provision

In most cases, the large rotors and calipers will require the use of aftermarket wheels for adequate brake clearance. Dinan’s soon to be released 19" lightweight performance wheels are recommended, providing proper clearance and the ability to fit the largest tires possible for optimum performance. Be sure to check with the manufacturer or distributor of the wheels you are considering in order to verify that they offer the necessary clearance, citing the Brembo “Gran Turismo” brakes as a reference. A fitment guide, including templates for the various applications, is available by clicking on the link below or you may select "Technical/Forms" from the navigation bar above, then select "Miscellaneous".
Brembo_Caliper_Templates.pdf








Click here for printable version of this product back to top

Dinan/Brembo Front Brake Conversion-Red
Chassis Tuning

Part #:

Price:
D290-0905-R
$3595.00

Labor Hours: 2.80
Required Products: 18" or larger wheels.
Point Value: 3


Dinan Performance Brakes by Brembo are now available for E90 335i applications providing the driving enthusiast with ultimate stopping power for the street, as well as track events. Extensive testing has enabled us to develop custom systems that have been tuned for optimum performance, while avoiding the foibles of typical “big brake kits”, such as unbalanced proportioning, poor pedal feel and unacceptable noise levels, just to name a few. The brake calipers are available in either red or black, giving you the choice of a stealth or competition look.





The Dinan/Brembo Front Brake Conversion Features:
Front Rotors: 355mm Slotted with Aluminum Hats (Stock Rotors Measure 330mm)
Calipers: 4-Piston, Aluminum (Available in Black or Red)
Goodridge DOT/TUV Approved Stainless Steel Brake Lines
Mounting Brackets and Assembly Hardware
Dinan-spec Ferodo Brake Pads with Sensor Provision

In most cases, the large rotors and calipers will require the use of aftermarket wheels for adequate brake clearance. Dinan’s soon to be released 19" lightweight performance wheels are recommended, providing proper clearance and the ability to fit the largest tires possible for optimum performance. Be sure to check with the manufacturer or distributor of the wheels you are considering in order to verify that they offer the necessary clearance, citing the Brembo “Gran Turismo” brakes as a reference. A fitment guide, including templates for the various applications, is available by clicking on the link below or you may select "Technical/Forms" from the navigation bar above, then select "Miscellaneous".
Brembo_Caliper_Templates.pdf








Click here for printable version of this product back to top

Dinan/Brembo Rear Brake Conversion-Black
Chassis Tuning

Part #:

Price:
D290-0903-B
$2795.00

Labor Hours: 3.90
Required Products: For use with Dinan/Brembo Front Brake Conversion. 18" or larger wheels required.


Dinan Performance Brakes by Brembo are available separately for rear E90 335i applications designed specifically for use with the front brake conversion. The brake calipers are available in either red or black, giving you the choice of a stealth or competition look.





The Dinan/Brembo Rear Brake Conversion Features:
Rear Rotors: 345mm Slotted with Aluminum Hats (Stock Rotors Measure 336mm)
Calipers: 4-Piston, Aluminum (Available in Black or Red)
Goodridge DOT/TUV Approved Stainless Steel Brake Lines
Mounting Brackets and Assembly Hardware
Dinan-spec Ferodo Brake Pads with Sensor Provision

In most cases, the large rotors and calipers will require the use of aftermarket wheels for adequate brake clearance. Dinan’s soon to be released 19" lightweight performance wheels are recommended, providing proper clearance and the ability to fit the largest tires possible for optimum performance. Be sure to check with the manufacturer or distributor of the wheels you are considering in order to verify that they offer the necessary clearance, citing the Brembo “Gran Turismo” brakes as a reference. A fitment guide, including templates for the various applications, is available by clicking on the link below or you may select "Technical/Forms" from the navigation bar above, then select "Miscellaneous".
Brembo_Caliper_Templates.pdf








Click here for printable version of this product back to top

Dinan/Brembo Rear Brake Conversion-Red
Chassis Tuning

Part #:

Price:
D290-0903-R
$2795.00

Labor Hours: 3.90
Required Products: For use with Dinan/Brembo Front Brake Conversion. 18" or larger wheels required.


Dinan Performance Brakes by Brembo are available separately for rear E90 335i applications designed specifically for use with the front brake conversion. The brake calipers are available in either red or black, giving you the choice of a stealth or competition look.





The Dinan/Brembo Rear Brake Conversion Features:
Rear Rotors: 345mm Slotted with Aluminum Hats (Stock Rotors Measure 336mm)
Calipers: 4-Piston, Aluminum (Available in Black or Red)
Goodridge DOT/TUV Approved Stainless Steel Brake Lines
Mounting Brackets and Assembly Hardware
Dinan-spec Ferodo Brake Pads with Sensor Provision

In most cases, the large rotors and calipers will require the use of aftermarket wheels for adequate brake clearance. Dinan’s soon to be released 19" lightweight performance wheels are recommended, providing proper clearance and the ability to fit the largest tires possible for optimum performance. Be sure to check with the manufacturer or distributor of the wheels you are considering in order to verify that they offer the necessary clearance, citing the Brembo “Gran Turismo” brakes as a reference. A fitment guide, including templates for the various applications, is available by clicking on the link below or you may select "Technical/Forms" from the navigation bar above, then select "Miscellaneous".
Brembo_Caliper_Templates.pdf

[ksfrogman]

Most all of that is old news, except for the camber plates.