DPF issues... Opinions on DIS Figures??

mammoo6 · 08-31-2013, 07:08 PM

Hello guys,

So had the car for about 2 months now, driving tonight and the yellow particle filter warning flashed up on iDrive.

After reading some comments on here I took it out a good run, about 80 miles.

Came home and loaded up DIS and this is what it's saying... Do the figures look ok?

Cleared the fault code but I've been doing quite a bit of driving around town recently and short journeys so hopefully this will sort it out.

Cheers,
Matthew

rsmallwo · 09-01-2013, 05:01 AM

Whats your exhaust gas back pressure @ idle, 2 k revs and full throttle? Theres a test on the dis for this and it runs through the tests automatically, bar the last WOT test. Whilst testing it gives the max permissible value

mammoo6 · 09-01-2013, 05:46 AM

Quote:

Originally Posted by rsmallwo

Whats your exhaust gas back pressure @ idle, 2 k revs and full throttle? Theres a test on the dis for this and it runs through the tests automatically, bar the last WOT test. Whilst testing it gives the max permissible value

How do I access this test mate and I'll get the figures?

tmarshall57 · 09-01-2013, 07:20 AM

Quote:

Originally Posted by mammoo6

How do I access this test mate and I'll get the figures?

I posted a DIY guide on this subject last week here.....

http://www.e90post.com/forums/showthread.php?t=880821

mammoo6 · 09-01-2013, 08:16 AM

Cheers for that mate... Done the test and these are the figures...

What you think?

Dan-danGT · 09-01-2013, 10:11 AM

To me it's in need ofa regeneration as they above there Max value for that given range. I'm sure you can force a regen using inpa

mammoo6 · 09-01-2013, 10:14 AM

Quote:

Originally Posted by Dan-danGT

To me it's in need ofa regeneration as they above there Max value for that given range. I'm sure you can force a regen using inpa

I took it a run last night and the systems saying it regened 8miles ago... Think this is wrong and I should force a regen instead?

tmarshall57 · 09-01-2013, 10:35 AM

Quote:

Originally Posted by mammoo6

Cheers for that mate... Done the test and these are the figures...

What you think?

As above - these figures are over the maximum allowed and therefore likely to be the cause of the yellow light. It may require a few regens to burn off the soot to a level significantly below maximum. You can trigger a regen ising DIS but I don't think you can using INPA.

Try triggering a few regens over the next couple of weeks and test again.

Interesting that the maximum allowed backpressure on your car is significantly lower than on mine

mammoo6 · 09-01-2013, 10:39 AM

Will do guys... Took it another run today and no sign of the warning so hopefully it's just needing a good clear out but I'll keep an eye on it...

Cheers again

regy53 · 09-01-2013, 11:59 AM

What software is this? hope your prob is sorted

mammoo6 · 09-01-2013, 12:35 PM

Quote:

Originally Posted by tmarshall57

Quote:

Originally Posted by mammoo6

Cheers for that mate... Done the test and these are the figures...

What you think?

As above - these figures are over the maximum allowed and therefore likely to be the cause of the yellow light. It may require a few regens to burn off the soot to a level significantly below maximum. You can trigger a regen ising DIS but I don't think you can using INPA.

Try triggering a few regens over the next couple of weeks and test again.

Interesting that the maximum allowed backpressure on your car is significantly lower than on mine

What's the maximum back pressure allowed on yours mate?

I thought it was quite low as well

mammoo6 · 09-01-2013, 12:36 PM

Quote:

Originally Posted by regy53

What software is this? hope your prob is sorted

DIS software with an OBD Cable

tmarshall57 · 09-01-2013, 01:14 PM

Quote:

Originally Posted by mammoo6

What's the maximum back pressure allowed on yours mate?

I thought it was quite low as well

Idle - 65
2000 RPM - 150
4000 RPM - 250

mammoo6 · 09-01-2013, 01:16 PM

Quote:

Originally Posted by tmarshall57

Quote:

Originally Posted by mammoo6

What's the maximum back pressure allowed on yours mate?

I thought it was quite low as well

Idle - 65
2000 RPM - 150
4000 RPM - 250

That is a lot lower... Very odd... What year is yours? Is it 335d?

tmarshall57 · 09-01-2013, 04:14 PM

Quote:

Originally Posted by mammoo6

That is a lot lower... Very odd... What year is yours? Is it 335d?

Feb 2007 build 330D

mammoo6 · 09-01-2013, 04:28 PM

Quote:

Originally Posted by tmarshall57

Quote:

Originally Posted by mammoo6

That is a lot lower... Very odd... What year is yours? Is it 335d?

Feb 2007 build 330D

On DIS... How do I perform a forced regen?

Looking at it just now and I can't find it..!!

tmarshall57 · 09-01-2013, 07:08 PM

Quote:

Originally Posted by mammoo6

On DIS... How do I perform a forced regen?

Looking at it just now and I can't find it..!!

Interesting - I thought the force regen option was one of those in the screenshot you posted. On that screen I don't get the "second last", "third last" regen but I do get the option to trigger a regen. I think our cars have some different options in DIS

mammoo6 · 09-01-2013, 07:12 PM

I found it mate... It's on the screen that tells you the values of the pressure when you do the pressure test.

Just as I went to do it the laptop cut out so I'll need to give it a go tomorrow but I'll let use know how I get on... Hopefully this will sort it out..!!

08-31-2013, 07:08 PM	#1
mammoo6 Private First Class 12 Rep 131 Posts Drives: Silver 335d SE Coupe Autovogue Join Date: Jul 2013 Location: Scotland iTrader: (0)	DPF issues... Opinions on DIS Figures?? Hello guys, So had the car for about 2 months now, driving tonight and the yellow particle filter warning flashed up on iDrive. After reading some comments on here I took it out a good run, about 80 miles. Came home and loaded up DIS and this is what it's saying... Do the figures look ok? Cleared the fault code but I've been doing quite a bit of driving around town recently and short journeys so hopefully this will sort it out. Cheers, Matthew Attached Images
	Appreciate 0 Tweet Quote

09-01-2013, 05:01 AM	#2
rsmallwo Captain 42 Rep 939 Posts Drives: Z4 35i Join Date: Jan 2010 Location: Hull iTrader: (0)	Whats your exhaust gas back pressure @ idle, 2 k revs and full throttle? Theres a test on the dis for this and it runs through the tests automatically, bar the last WOT test. Whilst testing it gives the max permissible value
	Appreciate 0 Quote

09-01-2013, 08:16 AM	#5
mammoo6 Private First Class 12 Rep 131 Posts Drives: Silver 335d SE Coupe Autovogue Join Date: Jul 2013 Location: Scotland iTrader: (0)	Cheers for that mate... Done the test and these are the figures... What you think? Attached Images
	Appreciate 0 Quote

09-01-2013, 10:11 AM	#6
Dan-danGT Captain 35 Rep 650 Posts Drives: E90 330d M-Sport Join Date: Dec 2012 Location: Nottinghamshire iTrader: (0)	To me it's in need ofa regeneration as they above there Max value for that given range. I'm sure you can force a regen using inpa
	Appreciate 0 Quote

09-01-2013, 10:39 AM	#9
mammoo6 Private First Class 12 Rep 131 Posts Drives: Silver 335d SE Coupe Autovogue Join Date: Jul 2013 Location: Scotland iTrader: (0)	Will do guys... Took it another run today and no sign of the warning so hopefully it's just needing a good clear out but I'll keep an eye on it... Cheers again
	Appreciate 0 Quote

09-01-2013, 11:59 AM	#10
regy53 Second Lieutenant 10 Rep 204 Posts Drives: 335d Join Date: Jul 2013 Location: Leighton Buzzard iTrader: (0)	What software is this? hope your prob is sorted
	Appreciate 0 Quote

09-01-2013, 07:12 PM	#18
mammoo6 Private First Class 12 Rep 131 Posts Drives: Silver 335d SE Coupe Autovogue Join Date: Jul 2013 Location: Scotland iTrader: (0)	I found it mate... It's on the screen that tells you the values of the pressure when you do the pressure test. Just as I went to do it the laptop cut out so I'll need to give it a go tomorrow but I'll let use know how I get on... Hopefully this will sort it out..!!
	Appreciate 0 Quote