Don't use these people to vinyl wrap anything.

mob17 · 09-09-2013, 03:11 PM

Have you tried it yourself?

Poison32 · 09-09-2013, 03:51 PM

Quote:

Originally Posted by TheBlondeFella

I'll post a snap as soon as I can

thanks apprieciate that

TheBlondeFella · 09-10-2013, 02:40 PM

So here are the snaps that were asked for. The general shots look quite nice and the black brushed aluminum finish looks great. The few close up shots that I've attached show how bad the finish of applying the vinyl is!

jammy78 · 09-10-2013, 02:43 PM

That is shocking!!!

225_AB · 09-10-2013, 03:45 PM

Bloody awful

dxb335d · 09-10-2013, 03:45 PM

So much easier to buy a car which already has a nice interior trim.

mob17 · 09-10-2013, 03:49 PM

Omg even i did a better job of that with no experience.

OP try it yourself. Just need a hair dryer or a heat gun and some patience.

Geesh_46 · 09-11-2013, 10:36 AM

That is really poor! it's not cheap material either, bet the original guy hopes you don't go back so he doesn't waste any more material, you do have to be really good to do a proper job, I decided to spray mine as I could get a better finish, the black alu does look really nice though! (tempted to order some).

Which make of material did he use do you know? as I know 3M is around £50 a linear metre but you can get cheap crap which is about £20 a linear metre.

CustomColours · 09-11-2013, 12:49 PM

Those peeling issues are due to bad heating and overstrtching. I would put an unnoticable side panel where its peeled on the side for reassurance and as for the reat I dont think id be able to create that mess if I tried to be fair with you.

TheBlondeFella · 09-11-2013, 02:32 PM

It's the 3M stuff or it should be anyway ...

I don't think that they will call me back and to be quite honest I'm happy with that.

I'm really happy with the brushed Ali and I'm my opinion is much classier than the more commonly used carbon.

Just need to organise a decent place to do it properly now ....

oliyaoe93 · 09-11-2013, 02:40 PM

I just had my car wrapped by SurreyProjects. Check my posts. Must say im not extreamly happy with the wrap. However, they have told me to go back, i hope they will re-wrap some dodgy bits.

09-09-2013, 03:11 PM	#23
mob17 Major General 397 Rep 5,613 Posts Drives: E92 335D Join Date: Mar 2012 Location: East Midlands, UK iTrader: (5)	Have you tried it yourself?
	Appreciate 0 Quote

09-10-2013, 02:40 PM	#25
TheBlondeFella First Lieutenant 40 Rep 386 Posts Drives: E93 320i M Sport Join Date: Jun 2013 Location: Surrey, UK iTrader: (3)	So here are the snaps that were asked for. The general shots look quite nice and the black brushed aluminum finish looks great. The few close up shots that I've attached show how bad the finish of applying the vinyl is! Attached Images
	Appreciate 0 Quote

09-10-2013, 02:43 PM	#26
jammy78 Colonel 137 Rep 2,012 Posts Drives: F31 335D Join Date: Nov 2012 Location: Windsor iTrader: (21)	That is shocking!!!
	Appreciate 0 Quote

09-10-2013, 03:45 PM	#27
225_AB Major 67 Rep 1,374 Posts Drives: M235i Join Date: May 2010 Location: buckinghamshire iTrader: (1) Garage List 2014 M235i [0.00] 2009 BMW 330D [0.00]	Bloody awful
	Appreciate 0 Quote

09-10-2013, 03:45 PM	#28
dxb335d The Tarmac Terrorist 1008 Rep 29,344 Posts Drives: 997.2 GT3 Join Date: Mar 2007 Location: ''Fandango Towers'' iTrader: (3) Garage List 2010 Porsche 997.2 GT3 [9.50] 2003 BMW E46 M3 [6.00] 2007 BMW E92 335D [5.50]	So much easier to buy a car which already has a nice interior trim.
	Appreciate 0 Quote

09-10-2013, 03:49 PM	#29
mob17 Major General 397 Rep 5,613 Posts Drives: E92 335D Join Date: Mar 2012 Location: East Midlands, UK iTrader: (5)	Omg even i did a better job of that with no experience. OP try it yourself. Just need a hair dryer or a heat gun and some patience.
	Appreciate 0 Quote

09-11-2013, 10:36 AM	#30
Geesh_46 Private 3 Rep 88 Posts Drives: BMW E90 330D Join Date: Oct 2012 Location: Stoke-on-Trent iTrader: (0)	That is really poor! it's not cheap material either, bet the original guy hopes you don't go back so he doesn't waste any more material, you do have to be really good to do a proper job, I decided to spray mine as I could get a better finish, the black alu does look really nice though! (tempted to order some). Which make of material did he use do you know? as I know 3M is around £50 a linear metre but you can get cheap crap which is about £20 a linear metre.
	Appreciate 0 Quote

09-11-2013, 12:49 PM	#31
CustomColours Banned 16 Rep 791 Posts Drives: 335i SE Join Date: Apr 2012 Location: Hertfordshire iTrader: (0)	Those peeling issues are due to bad heating and overstrtching. I would put an unnoticable side panel where its peeled on the side for reassurance and as for the reat I dont think id be able to create that mess if I tried to be fair with you.
	Appreciate 0 Quote

09-11-2013, 02:32 PM	#32
TheBlondeFella First Lieutenant 40 Rep 386 Posts Drives: E93 320i M Sport Join Date: Jun 2013 Location: Surrey, UK iTrader: (3)	It's the 3M stuff or it should be anyway ... I don't think that they will call me back and to be quite honest I'm happy with that. I'm really happy with the brushed Ali and I'm my opinion is much classier than the more commonly used carbon. Just need to organise a decent place to do it properly now ....
	Appreciate 0 Quote

09-11-2013, 02:40 PM	#33
oliyaoe93 Private First Class 20 Rep 109 Posts Drives: 320i LCI e93 Join Date: Aug 2013 Location: South London iTrader: (0)	I just had my car wrapped by SurreyProjects. Check my posts. Must say im not extreamly happy with the wrap. However, they have told me to go back, i hope they will re-wrap some dodgy bits.
	Appreciate 0 Quote