V2 installed

addicted 2 turbo · 12-12-2007, 09:10 PM

I have my V2 install by dyno4mance (706-602-8881) in GA 40 mile from ATL. I’m really happy with my installation, they are very professionals & good customer service.
After my 4 hour drive he dyno my car it dyno 306 WHP with Procede 1.45 is low but the car was heat soak after 4 hour drive after the v2 installed the car dyno 336 WHP. The car is set up at 94% and after 5000 rpm 96%.
Thanks to noize , Andrew and the installer (forgot his name)

p.s I just move to Fort myers once i get my household good i will post the dyno sheet

Boostin335 · 12-12-2007, 09:13 PM

336 is low for v2 with those bumped up settings no?

addicted 2 turbo · 12-12-2007, 09:16 PM

Quote:

Originally Posted by Boostin335

336 is low for v2 with those bumped up settings no?

the way I look at it there was a gained of 30 H.P regardless and the car was very hot because of the 4 hour drive.
the car feels a lot more faster now

Boostin335 · 12-12-2007, 09:18 PM

Quote:

Originally Posted by boriquaguerrero

the way I look at it there was a gained of 30 H.P regardless and the car was very hot because of the 4 hour drive.

but didnt it cool down - you get to shop, BS for a few im sure, then install v2, then dyno?

It needs time to adapt also, i think.

If you dynoed right after your #s will get higher, but shouldn't it of been cool after the install?

zenmaster · 12-12-2007, 09:20 PM

Well at least now we know how much power a partially adapted, heat-soaked v2.0.2 @ 96% can put down.

addicted 2 turbo · 12-12-2007, 09:22 PM

Quote:

Originally Posted by Boostin335

but didnt it cool down - you get to shop, BS for a few im sure, then install v2, then dyno?

It needs time to adapt also, i think.

If you dynoed right after your #s will get higher, but shouldn't it of been cool after the install?

it was a bad day long story short i got there by 430pm and my appt was at 300 pm but they still took care of me even thought they close at 500pm (it did not take long to get it done)

im happy with it

scalbert · 12-12-2007, 09:30 PM

I need to apologize for not getting back with you about the installation. It slipped my mind.

We could have done it on Saturday while we were installing DrewKo's DP's. Unfortunately, I do not have a dyno in my garage.

addicted 2 turbo · 12-12-2007, 09:34 PM

[QUOTE=scalbert;1815706]I need to apologize for not getting back with you about the installation. It slipped my mind.

We could have done it on Saturday while we were installing DrewKo's DP's. Unfortunately, I do not have a dyno in my garage.[/QUOTE

No problem man how is DREWKO doing?

Ruff Rider · 12-12-2007, 09:35 PM

Quote:

Originally Posted by scalbert

I need to apologize for not getting back with you about the installation. It slipped my mind.

We could have done it on Saturday while we were installing DrewKo's DP's. Unfortunately, I do not have a dyno in my garage.

I thought we all had dyno's in our garages

scalbert · 12-12-2007, 09:38 PM

Quote:

Originally Posted by boriquaguerrero

No problem man how is DREWKO doing?

His pipes are in and runnigng well.

scalbert · 12-12-2007, 09:39 PM

Quote:

Originally Posted by Ruff Rider

I thought we all had dyno's in our garages

That depends on the amount of beer consumed.

Ruff Rider · 12-12-2007, 09:52 PM

Quote:

Originally Posted by scalbert

That depends on the amount of beer consumed.

CanadianTSi · 12-12-2007, 09:58 PM

What were the Torque numbers? Also what kind of Dyno is it?

OpenFlash · 12-12-2007, 09:59 PM

Hey guys... Dyno4mance has a state of the art Dyno Dynamics AWD load bearing dyno. They read 10-12% lower than Dynojets. I know, I have one

Glad to hear everything went well. Andrew and Seth are good folk!

Shiv

scalbert · 12-12-2007, 10:24 PM

Quote:

Originally Posted by shiv@vishnu

Hey guys... Dyno4mance has a state of the art Dyno Dynamics AWD load bearing dyno. They read 10-12% lower than Dynojets. I know, I have one

Glad to hear everything went well. Andrew and Seth are good folk!

Shiv

As run on the same dyno. Soon after I made quite a bit more on a Dynojet. FYI, the date is wrong. It was January 8th.

DrewKo · 12-13-2007, 12:37 AM

[QUOTE=boriquaguerrero;1815728]

Quote:

Originally Posted by scalbert

I need to apologize for not getting back with you about the installation. It slipped my mind.

We could have done it on Saturday while we were installing DrewKo's DP's. Unfortunately, I do not have a dyno in my garage.[/QUOTE

No problem man how is DREWKO doing?

Hey Angel! Doing good man, tx for asking. That dyno result you got is actually damn good because the dyno you used reads a bit lower (as Shiv pointed out above). I bet your car is running very strong now; wish I had been there.

I had some catted DPs from Ultimate Racing installed and will get a dyno in about 10 days (not sure yet if they are worth the money, but I'll reserve judgment for now). I have been told my V2 is on its way in a couple of weeks. We'll have to compare the dyno charts then!! Take care bro.

12-12-2007, 09:10 PM	#1
addicted 2 turbo 3rd Brigade Combat Team 32 Rep 424 Posts Drives: BMW 335 & 328 Join Date: Jan 2007 Location: FORT CARSON, CO iTrader: (3)	V2 installed I have my V2 install by dyno4mance (706-602-8881) in GA 40 mile from ATL. I’m really happy with my installation, they are very professionals & good customer service. After my 4 hour drive he dyno my car it dyno 306 WHP with Procede 1.45 is low but the car was heat soak after 4 hour drive after the v2 installed the car dyno 336 WHP. The car is set up at 94% and after 5000 rpm 96%. Thanks to noize , Andrew and the installer (forgot his name) p.s I just move to Fort myers once i get my household good i will post the dyno sheet __________________ 2012 E92 335 , F30 328 , 09 535 88 RX7 Turbo, 85 RX7 2010 RX8
	Appreciate 0 Tweet Quote

12-12-2007, 09:13 PM	#2
Boostin335 Lieutenant Colonel 765 Rep 1,815 Posts Drives: F92 M8, G82 M4, C8, MKIV Supra Join Date: Sep 2007 Location: North/Central NJ iTrader: (3)	336 is low for v2 with those bumped up settings no?
	Appreciate 0 Quote

12-12-2007, 09:20 PM	#5
zenmaster Brigadier General 1585 Rep 3,888 Posts Drives: '17 M2 Join Date: Mar 2007 Location: Atlanta iTrader: (1)	Well at least now we know how much power a partially adapted, heat-soaked v2.0.2 @ 96% can put down.
	Appreciate 0 Quote

12-12-2007, 09:30 PM	#7
scalbert Major General 161 Rep 5,776 Posts Drives: '13 S4, '15 Q7 Join Date: Feb 2007 Location: Woodstock, GA iTrader: (8)	I need to apologize for not getting back with you about the installation. It slipped my mind. We could have done it on Saturday while we were installing DrewKo's DP's. Unfortunately, I do not have a dyno in my garage.
	Appreciate 0 Quote

12-12-2007, 09:34 PM	#8
addicted 2 turbo 3rd Brigade Combat Team 32 Rep 424 Posts Drives: BMW 335 & 328 Join Date: Jan 2007 Location: FORT CARSON, CO iTrader: (3)	[QUOTE=scalbert;1815706]I need to apologize for not getting back with you about the installation. It slipped my mind. We could have done it on Saturday while we were installing DrewKo's DP's. Unfortunately, I do not have a dyno in my garage.[/QUOTE No problem man how is DREWKO doing? __________________ 2012 E92 335 , F30 328 , 09 535 88 RX7 Turbo, 85 RX7 2010 RX8
	Appreciate 0 Quote

12-12-2007, 09:58 PM	#13
CanadianTSi Captain 209 Rep 607 Posts Drives: 2014 535 xDrive Diesel Join Date: Feb 2007 Location: Alberta iTrader: (0)	What were the Torque numbers? Also what kind of Dyno is it?
	Appreciate 0 Quote

12-12-2007, 09:59 PM	#14
OpenFlash 1849 Rep 17,960 Posts Drives: A Lot Join Date: Sep 2006 Location: SF Bay, CA iTrader: (0) Garage List 2018 Ducati Panigal ... [0.00] 2016 Mazda CX5 [0.00] 2017 Aprilia Tuono ... [0.00] 2019 BMW M2 Competi ... [0.00] 2015 BMW M5 Competi ... [10.00] 2016 Ducati XDiavel S [0.00] 2016 AMG GT S [0.00] 2011 Ferrari 458 It ... [0.00] 2017 Charger Hellcat [0.00] 2015 KTM Super Duke ... [0.00] 2016 KTM RC390 [0.00]	Hey guys... Dyno4mance has a state of the art Dyno Dynamics AWD load bearing dyno. They read 10-12% lower than Dynojets. I know, I have one Glad to hear everything went well. Andrew and Seth are good folk! Shiv
	Appreciate 0 Quote