Double blinking "Euro" hazards only work while engine is running?

dwells · 04-22-2014, 08:46 AM

Does anyone know how to get the double blinking Euro hazards to work while the engine is off as well? I noticed that the engine has to be running for them to work. In fact, if you turn the engine off while the hazards are on, they immediately switch back to the conventional single blink.

I enabled DOPPELBLINKIMPULS_WARNBLK only - does DOPPELBLINKIMPULS_CRASH allow it to work when the engine is off?

Andrewe92 · 04-22-2014, 10:06 AM

Quote:

Originally Posted by dwells

Does anyone know how to get the double blinking Euro hazards to work while the engine is off as well? I noticed that the engine has to be running for them to work. In fact, if you turn the engine off while the hazards are on, they immediately switch back to the conventional single blink.

I enabled DOPPELBLINKIMPULS_WARNBLK only - does DOPPELBLINKIMPULS_CRASH allow it to work when the engine is off?

according to multiple coding sheets... "DOPPELBLINKIMPULS_CRASH" will apply double blinkers when you crash haha but anyway yea you are correct it is only when the engine is on. I don't think I have seen anyone accomplish what you are asking about. keep looking!

http://www.bmw-one.com/staff/doc/BMW..._Code_List.pdf

joepcrepairs2 · 04-22-2014, 10:57 AM

Quote:

Originally Posted by dwells

Does anyone know how to get the double blinking Euro hazards to work while the engine is off as well? I noticed that the engine has to be running for them to work. In fact, if you turn the engine off while the hazards are on, they immediately switch back to the conventional single blink.

I enabled DOPPELBLINKIMPULS_WARNBLK only - does DOPPELBLINKIMPULS_CRASH allow it to work when the engine is off?

works with engine runing or not running idk why yours dont..

are you sure you enable it it??

is it frm1 or frm2?

dwells · 04-22-2014, 11:02 AM

Quote:

Originally Posted by Andrewe92

anyway yea you are correct it is only when the engine is on. I don't think I have seen anyone accomplish what you are asking about. keep looking![/url]

Interesting, thanks. I went through the FRM thoroughly and couldn't find any other references to it.

Quote:

Originally Posted by *************

works with engine runing or not running idk why yours dont..

are you sure you enable it it??

is it frm1 or frm2?

FRM3 with latest firmware on an LCI E93. It's definitely enabled, I did a read out after I finished coding to verify that it had stuck. It only works with the engine on (or maybe just ignition at least).

joepcrepairs2 · 04-22-2014, 11:04 AM

Quote:

Originally Posted by dwells

Interesting, thanks. I went through the FRM thoroughly and couldn't find any other references to it.

FRM3 with latest firmware on an LCI E93. It's definitely enabled, I did a read out after I finished coding to verify that it had stuck. It only works with the engine on (or maybe just ignition at least).

post a copy of your trc file so I can look aat it

joepcrepairs2 · 04-22-2014, 11:28 AM

try enabling
DOPPELBLINKIMPULS_CRASH

and if they still dont work when engine is off

WARNBLK_ENERGY_SAVE_MODE change this value to nicht aktiv

dwells · 04-22-2014, 11:37 AM

Looks like STROMSPAR_WARNBLINKEN might have an impact as well. I'll test it when I have a chance.

joepcrepairs2 · 04-24-2014, 11:54 PM

today I was coding a 2008 x5 and notice that double blink hazards only stay om while engine runing since car has frm3... I disable the power saving mode and now they work with or without engine running.

joepcrepairs2 · 04-25-2014, 12:35 AM

Quote:

Originally Posted by *************

today I was coding a 2008 x5 and notice that double blink hazards only stay om while engine runing since car has frm3... I disable the power saving mode and now they work with or without engine running.

this to nicht aktiv

WARNBLK_ENERGY_SAVE_MODE

dwells · 04-25-2014, 11:10 AM

Quote:

Originally Posted by *************

this to nicht aktiv

WARNBLK_ENERGY_SAVE_MODE

Good stuff, thanks. Guess it makes sense that it does this by default - prolongs how long the car can keep it's flashers running on the side of the road if it were to break down.

SteveEvans · 12-09-2016, 02:36 PM

Quote:

Originally Posted by *************

this to nicht aktiv

WARNBLK_ENERGY_SAVE_MODE

That didn't work for me (2012 LCI E92 M3). Well, to be precise, I get double blink if the key is in; the engine doesn't need to be running.

I'm wondering if WARNBLK_ENERGY_SAVE_AHM being aktiv might be to blame? I shall have to try again.

Steve

LMB335IS · 12-09-2016, 04:11 PM

Quote:

Originally Posted by SteveEvans

Quote:

Originally Posted by *************

this to nicht aktiv

WARNBLK_ENERGY_SAVE_MODE

That didn't work for me (2012 LCI E92 M3). Well, to be precise, I get double blink if the key is in; the engine doesn't need to be running.

I'm wondering if WARNBLK_ENERGY_SAVE_AHM being aktiv might be to blame? I shall have to try again.

Steve

Set STROMSPAR_WARNBLINKEN to nicht aktiv.

04-22-2014, 08:46 AM	#1
dwells ಠ_ಠ 78 Rep 1,539 Posts Drives: Monaco Blue 335i coupe Join Date: Nov 2010 Location: New England iTrader: (6)	Double blinking "Euro" hazards only work while engine is running? Does anyone know how to get the double blinking Euro hazards to work while the engine is off as well? I noticed that the engine has to be running for them to work. In fact, if you turn the engine off while the hazards are on, they immediately switch back to the conventional single blink. I enabled DOPPELBLINKIMPULS_WARNBLK only - does DOPPELBLINKIMPULS_CRASH allow it to work when the engine is off? __________________ \| 335i coupe \| Monaco Blue \| JB4 G5 ISO \| Style 313M \| Huper 40% tint \| Aero lip \| CSL trunk spoiler \| M3 sideskirts \| Paint-matched grilles \| Painted reflectors \| GP Thunder II angel eyes \| Smoked LED sidemarkers \| Self-coded \|
	Appreciate 0 Tweet Quote

04-22-2014, 11:28 AM	#6
joepcrepairs2 Banned 16 Rep 128 Posts Drives: e92 Join Date: Mar 2014 Location: Norwalk, Ca iTrader: (0)	try enabling DOPPELBLINKIMPULS_CRASH and if they still dont work when engine is off WARNBLK_ENERGY_SAVE_MODE change this value to nicht aktiv
	Appreciate 0 Quote

04-22-2014, 11:37 AM	#7
dwells ಠ_ಠ 78 Rep 1,539 Posts Drives: Monaco Blue 335i coupe Join Date: Nov 2010 Location: New England iTrader: (6)	Looks like STROMSPAR_WARNBLINKEN might have an impact as well. I'll test it when I have a chance. __________________ \| 335i coupe \| Monaco Blue \| JB4 G5 ISO \| Style 313M \| Huper 40% tint \| Aero lip \| CSL trunk spoiler \| M3 sideskirts \| Paint-matched grilles \| Painted reflectors \| GP Thunder II angel eyes \| Smoked LED sidemarkers \| Self-coded \|
	Appreciate 0 Quote

04-24-2014, 11:54 PM	#8
joepcrepairs2 Banned 16 Rep 128 Posts Drives: e92 Join Date: Mar 2014 Location: Norwalk, Ca iTrader: (0)	today I was coding a 2008 x5 and notice that double blink hazards only stay om while engine runing since car has frm3... I disable the power saving mode and now they work with or without engine running.
	Appreciate 0 Quote