Disconnected battery, now my windows wont roll up with the remote

vibroluxious · 06-18-2018, 08:26 PM

I had previously coded my CAS to allow me to roll my windows up and sunroof to close on my 2009 328i Xdrive. I also set my mirrors to fold/unfold with the fob. All worked well until this weekend when I disconnected the battery to replace my VCG. After hooking the battery back up, I found my windows no longer rolled up and the mirrors no longer folded/unfolded with the fob. I assumed the coding reverted back to the original VO but when looking at the TRC files it still shows the windows as activ. I tried resetting the CAS and NFRM to factory using a profile with manipulate turned off and the CAS resets everything back to the VO except the windows which still show as activ. I tried to set them to nichtactiv but they keep reverting back to activ. My assumption is that I need to get the CAS back to it's original settings and then re-code it but I don't seem to be able to do that. Any suggestions would be great.
Thanks

Sensible_ · 06-19-2018, 02:06 PM

Quote:

Originally Posted by vibroluxious

I had previously coded my CAS to allow me to roll my windows up and sunroof to close on my 2009 328i Xdrive. I also set my mirrors to fold/unfold with the fob. All worked well until this weekend when I disconnected the battery to replace my VCG. After hooking the battery back up, I found my windows no longer rolled up and the mirrors no longer folded/unfolded with the fob. I assumed the coding reverted back to the original VO but when looking at the TRC files it still shows the windows as activ. I tried resetting the CAS and NFRM to factory using a profile with manipulate turned off and the CAS resets everything back to the VO except the windows which still show as activ. I tried to set them to nichtactiv but they keep reverting back to activ. My assumption is that I need to get the CAS back to it's original settings and then re-code it but I don't seem to be able to do that. Any suggestions would be great.
Thanks

Any fault codes?

vibroluxious · 06-19-2018, 07:21 PM

When I hold down the lock button on the remote to try and close the windows, the car throws the following codes:

00A3B2 message error (terminal status, 0x130), receiver instrument panel, transmitter CAS

00CF14 no message (terminal status) from CAS, receiver DKG/EGS, transmitter DME-DDI

The codes will clear normally and don't return unless I try and close the windows with the remote.
Is there anything I need to reset after having the battery negative cable disconnected for a few hours?
I reset the steering angle sensor using ISTA-D after I hooked the battery back up but nothing else.

06-18-2018, 08:26 PM	#1
vibroluxious New Member 4 Rep 21 Posts Drives: 2009 3281 X-Drive Join Date: May 2018 Location: Ohio iTrader: (0)	Disconnected battery, now my windows wont roll up with the remote I had previously coded my CAS to allow me to roll my windows up and sunroof to close on my 2009 328i Xdrive. I also set my mirrors to fold/unfold with the fob. All worked well until this weekend when I disconnected the battery to replace my VCG. After hooking the battery back up, I found my windows no longer rolled up and the mirrors no longer folded/unfolded with the fob. I assumed the coding reverted back to the original VO but when looking at the TRC files it still shows the windows as activ. I tried resetting the CAS and NFRM to factory using a profile with manipulate turned off and the CAS resets everything back to the VO except the windows which still show as activ. I tried to set them to nichtactiv but they keep reverting back to activ. My assumption is that I need to get the CAS back to it's original settings and then re-code it but I don't seem to be able to do that. Any suggestions would be great. Thanks
	Appreciate 0 Tweet Quote

06-19-2018, 07:21 PM	#3
vibroluxious New Member 4 Rep 21 Posts Drives: 2009 3281 X-Drive Join Date: May 2018 Location: Ohio iTrader: (0)	When I hold down the lock button on the remote to try and close the windows, the car throws the following codes: 00A3B2 message error (terminal status, 0x130), receiver instrument panel, transmitter CAS 00CF14 no message (terminal status) from CAS, receiver DKG/EGS, transmitter DME-DDI The codes will clear normally and don't return unless I try and close the windows with the remote. Is there anything I need to reset after having the battery negative cable disconnected for a few hours? I reset the steering angle sensor using ISTA-D after I hooked the battery back up but nothing else.
	Appreciate 0 Quote