Faults after Radio Install BMW e90

bmwhitman · 04-01-2018, 06:48 PM

I just recently installed a used Professional Radio to replace my broken unit. All the features were the same except the newly installed one had a CD changer feature built in which I do not have currenlty. Surprisingly, the new radio worked with sound without any additonal programming.

When I recently scanned the radio with my BT scan tool under the MOST/CAN gateway CD73 module I received a few faults as follows:

E18D
Wake Up Device tried to wake up network 3-times without success (Error_WakeUp_Failed)
Error will not cause a warning light
Error is not currently present
Test conditions have been completed

E18F
Central registry does not match with debit configuration (Error_Registry_New)
Error will not cause a warning light
Error is not currently present
Test conditions have been completed

E190
Ring diagnosis check done (Error_Ring_Diagnose)
Error will not cause a warning light
Error is not currently present
Test conditions have been completed

E191
Too long and/or too many unlocks (Error_Unlock_Long)
Error will not cause a warning light
Error is not currently present
Test conditions have been completed

I have a few activation functions available that I can use with BT tool:
-Set Production date
-Set Transport date
-Set Service mode
-Set Wake up mode ON
-RAD_ON to supply
-Reset CCC Control Unit

Would one of the functions on my BT Tool clear these faults? Is the car computer not recognizing my new Radio? Any suggestions would be apprecaited.

ptpending · 04-02-2018, 05:11 AM

cd-changer is communicated over MOST bus
you radio have multiple errors about MOST bus ring
until you code out cd-changer option there errors will come up after every car sleep

bmwhitman · 04-02-2018, 03:26 PM

Quote:

Originally Posted by ptpending

cd-changer is communicated over MOST bus
you radio have multiple errors about MOST bus ring
until you code out cd-changer option there errors will come up after every car sleep

Is there any harm to the modules or control units if I don't code out the CD changer?

ctuna · 08-14-2018, 12:28 AM

Read out the 2rad or 2urad file to see what's enabled.
You can turn of the Most Bus by setting ring status to nicht activ.
I am not sure if I spelled activ right but you should only have
to add of subtract nicht.

CODIERUNG_ERFOLGT
codierung_erfolgt
CDC
nicht_aktiv
AUDIO_SYSTEM
pl2_hifi
pl3_hifi
SDARS
nicht_aktiv
PDC
nicht_aktiv
ACC
nicht_aktiv
STANDHEIZUNG
nicht_aktiv
AUX_RAD
aux
BAUREIHEX
e9x
COUNTRYCODE_RADIO
us
IBOC
nicht_aktiv
KEY_MEMORY_R
aktiv
MUTE_TIMES
pl2
NACHLAUF_INT_R
pl2
RIGHTHAND
nicht_aktiv
SOFTEN_ENTERTAINMENT_PDC
nicht_aktiv
TCU_ECE
nicht_aktiv
TIMEOUT_INT_R
pl2
ULF_ECE
nicht_aktiv
BMW_AKD
nicht_aktiv
BMW_HOME_DEALER
aktiv
BMW_INITIALIZE
aktiv
BMW_MOBILE_SERVICE
aktiv
BMW_PHONE_SERVICES
nicht_aktiv
BMW_ROAMING
nicht_aktiv
BMW_TELESERVICE_ONLY
nicht_aktiv
RING_STATUS
aktiv
BLUETOOTH_RAD2
aktiv
DISPLAY_LOGIC7
nicht_aktiv
HI_TEMP_VOL_CTRL
pl2_hifi
pl3_hifi
SMS_RAD2
nicht_aktiv
PHONE_BUSINESS_R2
nicht_aktiv
SVS_LOW_RAD2
aktiv
BMW_ASSIST_RAD2
aktiv
BMW_HOTLINE_RAD2
aktiv
DAB
nicht_aktiv
CAR_COMP_ACTIVE
aktiv
TCU_JAP
nicht_aktiv
CONTACT_NR_DEALER
aktiv
CONTACT_NR_HOTLINE
aktiv
CONTACT_NR_MOBILE_SRVC
aktiv
ABS_VOL_GONG
e91_hifi
CROSSOVER
pl2_hifi
e90_hifi
r56_stereo
r56_hifi
DELTA_GONG_ENT
wert_0
DELTA_PDC_ENT
wert_0
RATIO_AUDIO_SOURCES
ece
us
VEHICLE_FILTERS
e81_stereo
e82_stereo
e87_stereo
e88_stereo
e90_stereo
e91_stereo
e92_stereo
e93_stereo
pl2_hifi
r56_hifi
VOL_TEL_MAX
stereo_mulf_e87
hifi_mulf_e87
top_hifi_mulf_e87
stereo_mulf_e90
hifi_mulf_e90
top_hifi_mulf_e90
stereo_mulf_e91
hifi_mulf_e91
top_hifi_mulf_e91
stereo_tcu
hifi_tcu
top_hifi_tcu
VOL_TEL_MIN
wert_0
VOLUME_TABLE
e91_hifi
MY_INFO_RAD2
nicht_aktiv
V_INFO_RAD2
nicht_aktiv
PHONE_PROF_RAD2
aktiv

This is from my pro radio with Most but I have Most
Change RING_STATUS to nicht aktiv to turn off the Most
Bus. CDC should say nicht aktiv to if you don't have it.
I would think your default coding the VO should have established
your original code but I would hand code it to be sure.

04-01-2018, 06:48 PM	#1
bmwhitman Private First Class 50 Rep 177 Posts Drives: E90 Join Date: Aug 2011 Location: Toronto iTrader: (0) Garage List 2006 BMW 330i (E90) [0.00]	Faults after Radio Install BMW e90 I just recently installed a used Professional Radio to replace my broken unit. All the features were the same except the newly installed one had a CD changer feature built in which I do not have currenlty. Surprisingly, the new radio worked with sound without any additonal programming. When I recently scanned the radio with my BT scan tool under the MOST/CAN gateway CD73 module I received a few faults as follows: E18D Wake Up Device tried to wake up network 3-times without success (Error_WakeUp_Failed) Error will not cause a warning light Error is not currently present Test conditions have been completed E18F Central registry does not match with debit configuration (Error_Registry_New) Error will not cause a warning light Error is not currently present Test conditions have been completed E190 Ring diagnosis check done (Error_Ring_Diagnose) Error will not cause a warning light Error is not currently present Test conditions have been completed E191 Too long and/or too many unlocks (Error_Unlock_Long) Error will not cause a warning light Error is not currently present Test conditions have been completed I have a few activation functions available that I can use with BT tool: -Set Production date -Set Transport date -Set Service mode -Set Wake up mode ON -RAD_ON to supply -Reset CCC Control Unit Would one of the functions on my BT Tool clear these faults? Is the car computer not recognizing my new Radio? Any suggestions would be apprecaited.
	Appreciate 0 Tweet Quote

04-02-2018, 05:11 AM	#2
ptpending Colonel 536 Rep 2,941 Posts Drives: e81 Join Date: Dec 2013 Location: Poland iTrader: (1)	cd-changer is communicated over MOST bus you radio have multiple errors about MOST bus ring until you code out cd-changer option there errors will come up after every car sleep __________________ E81 2007 130i 6cylinder Montego blue Retrofits: Harman Kardon, High-beam assistant, Removable tow hitch. Auto-dim folding exterior mirrors. Lumbar support. Perfomance Brakes.
	Appreciate 0 Quote

08-14-2018, 12:28 AM	#4
ctuna Lieutenant General 2045 Rep 13,364 Posts Drives: 325xi 06 wagon MT Join Date: Jan 2010 Location: Santa Cruz, Ca iTrader: (0)	Read out the 2rad or 2urad file to see what's enabled. You can turn of the Most Bus by setting ring status to nicht activ. I am not sure if I spelled activ right but you should only have to add of subtract nicht. CODIERUNG_ERFOLGT codierung_erfolgt CDC nicht_aktiv AUDIO_SYSTEM pl2_hifi pl3_hifi SDARS nicht_aktiv PDC nicht_aktiv ACC nicht_aktiv STANDHEIZUNG nicht_aktiv AUX_RAD aux BAUREIHEX e9x COUNTRYCODE_RADIO us IBOC nicht_aktiv KEY_MEMORY_R aktiv MUTE_TIMES pl2 NACHLAUF_INT_R pl2 RIGHTHAND nicht_aktiv SOFTEN_ENTERTAINMENT_PDC nicht_aktiv TCU_ECE nicht_aktiv TIMEOUT_INT_R pl2 ULF_ECE nicht_aktiv BMW_AKD nicht_aktiv BMW_HOME_DEALER aktiv BMW_INITIALIZE aktiv BMW_MOBILE_SERVICE aktiv BMW_PHONE_SERVICES nicht_aktiv BMW_ROAMING nicht_aktiv BMW_TELESERVICE_ONLY nicht_aktiv RING_STATUS aktiv BLUETOOTH_RAD2 aktiv DISPLAY_LOGIC7 nicht_aktiv HI_TEMP_VOL_CTRL pl2_hifi pl3_hifi SMS_RAD2 nicht_aktiv PHONE_BUSINESS_R2 nicht_aktiv SVS_LOW_RAD2 aktiv BMW_ASSIST_RAD2 aktiv BMW_HOTLINE_RAD2 aktiv DAB nicht_aktiv CAR_COMP_ACTIVE aktiv TCU_JAP nicht_aktiv CONTACT_NR_DEALER aktiv CONTACT_NR_HOTLINE aktiv CONTACT_NR_MOBILE_SRVC aktiv ABS_VOL_GONG e91_hifi CROSSOVER pl2_hifi e90_hifi r56_stereo r56_hifi DELTA_GONG_ENT wert_0 DELTA_PDC_ENT wert_0 RATIO_AUDIO_SOURCES ece us VEHICLE_FILTERS e81_stereo e82_stereo e87_stereo e88_stereo e90_stereo e91_stereo e92_stereo e93_stereo pl2_hifi r56_hifi VOL_TEL_MAX stereo_mulf_e87 hifi_mulf_e87 top_hifi_mulf_e87 stereo_mulf_e90 hifi_mulf_e90 top_hifi_mulf_e90 stereo_mulf_e91 hifi_mulf_e91 top_hifi_mulf_e91 stereo_tcu hifi_tcu top_hifi_tcu VOL_TEL_MIN wert_0 VOLUME_TABLE e91_hifi MY_INFO_RAD2 nicht_aktiv V_INFO_RAD2 nicht_aktiv PHONE_PROF_RAD2 aktiv This is from my pro radio with Most but I have Most Change RING_STATUS to nicht aktiv to turn off the Most Bus. CDC should say nicht aktiv to if you don't have it. I would think your default coding the VO should have established your original code but I would hand code it to be sure. Last edited by ctuna; 08-14-2018 at 01:27 AM..
	Appreciate 0 Quote