[Scrippy]

Guys,

Every one of my ZUSB #'s say it's not valid. I keep getting error 3000. I've updated my daten files using 50.2 E89 files. Any advice would be appreciated. I've gone through the coding forum and can't find any help.

[cryptomit]

What do you want to flash? Which module? Are you sure you have all necessary files imported properly?

[Scrippy]

Originally Posted by cryptomit

What do you want to flash? Which module? Are you sure you have all necessary files imported properly?

I want to update Kombi to gain the LCI sounds. I changed the values of HU_Verbaut_2 to _3_4 and it killed that nasty bell but now I have no audible tones. That is because the LCI gong is sent to HU from Kombi. I updated my daten files from the complet SP-Daten 50.2 pack. I used BMWTools to update the datens, so I couldn't really mess that part up.

[Sensible_]

Are you using comfort mode? The correct zusb number should be selected automatically...

[Scrippy]

Originally Posted by Sensible_

Are you using comfort mode? The correct zusb number should be selected automatically...

Yeah. I've never used WinKFP so I was aware it should auto recognize my Ecu's. I'm good on INPA and NCSExpert but not WinKFP.

[Sensible_]

What are the exact steps you are doing? As detailed as possible...

[Scrippy]

Originally Posted by Sensible_

What are the exact steps you are doing? As detailed as possible...

Start WinKFP.
Click "F1 Comfort Mode"
Click "F4 Enter Vin"
Click "F1 Enter ZUSB"
At this point none of my ZB#'s work. I'm using the numbers from my cars UIF file I grabbed with INPA.

If I click "F2 Choose ZUSB" it's empty.
If I click "F3 Uodte ZUSB" it's empty.
Here is a screen shot at this point.
I attached the error I get when I try any of my ZUSB numbers.

[Sensible_]

Unless you want a specific variant flash you need to do it like this:

1 - Start WinKFP, select COMFORT MODE and select F3:- Update ZUSB
2 - Select ECU family and the ECU will appear along with a list of part numbers. *DONT SELECT ANY NUMBER JUST ECU FAMILY - WINKFP CHOOSES CORRECT FILE*
3 - Select OK and the main menu will re-appear
4 - Select VIN and enter the cars VIN no. and select OK.
5 - Select Done
6 - Select Prog. ZB_update, you will be asked to confirm the update, Winkfp wil state the number of times the module can be re-programmed.

Your ECU family for KOMBI will probably by KOMB2 or something like that. Don't worry WINKFP is clever, it'll choose the correct one.

Also, make sure you code the KOMBI back to default in NCSexpert (expertmode profile) after the flash...

You won't find your current UIF ZUSB number from UIF as they are old and not in your new SP-DATEN.

[Scrippy]

Originally Posted by Sensible_

Unless you want a specific variant flash you need to do it like this:

1 - Start WinKFP, select COMFORT MODE and select F3:- Update ZUSB
2 - Select ECU family and the ECU will appear along with a list of part numbers. *DONT SELECT ANY NUMBER JUST ECU FAMILY - WINKFP CHOOSES CORRECT FILE*
3 - Select OK and the main menu will re-appear
4 - Select VIN and enter the cars VIN no. and select OK.
5 - Select Done
6 - Select Prog. ZB_update, you will be asked to confirm the update, Winkfp wil state the number of times the module can be re-programmed.

Your ECU family for KOMBI will probably by KOMB2 or something like that. Don't worry WINKFP is clever, it'll choose the correct one.

Also, make sure you code the KOMBI back to default in NCSexpert (expertmode profile) after the flash...

You won't find your current UIF ZUSB number from UIF as they are old and not in your new SP-DATEN.

Thank you so much man! I really appreciate that. Your directions were spot on!

[Scrippy]

So I was able to update my Amp60 and my Rad2 but the MOST_GW is eluding me. Anyone know what the ECU family is for that? I figured it was part of RAD2 but it wasn't.

[Scrippy]

Sensible_ and anyone else I really appreciate your help. I was able to update my ECU's to reflect my VIN. I had a different VIN for my MOST gateway, my RAD2, both seat modules and my amp. Attatched is my UIF list. It looks great now thanx to you guys. Only thing I can't do is update my Kombi. I have the daten file but it wont update. Attatched is the update attempt and the error. Any ideas?

[Sensible_]

Glad it's sorted

Re KOMBI. I'm seeing this more and more recently. No fix as yet. I'm beginning to think it's a fault with the daten files themselves. I'm researching this problem at the moment...

[Scrippy]

Originally Posted by Sensible_

Glad it's sorted

Re KOMBI. I'm seeing this more and more recently. No fix as yet. I'm beginning to think it's a fault with the daten files themselves. I'm researching this problem at the moment...

"Incorrect project number" is what the error is translated. Plus I don't have the file 9283839 on my PC anywhere, so wonder why it's even trying?