E90Post
 


Coby Wheel
 
BMW 3-Series (E90 E92) Forum > E90 / E92 / E93 3-series Powertrain and Drivetrain Discussions > N55 Turbo Engine Tuning and Exhaust Modifications - 335i Tuning > 2011 335i misfire cylinder 6



Reply
 
Thread Tools Search this Thread
      06-24-2023, 07:12 PM   #1
space_greymatt
Registered
0
Rep
3
Posts

Drives: 2018 X5, 2011 335I XDRIVE,
Join Date: Jun 2023
Location: NJ

iTrader: (0)

2011 335i misfire cylinder 6

Hi,

I currently have a 2011 335i XDRIVE with the following mods,
PURE STAGE 2 TURBO WITH HIGH FLOW
DINAN COILS
STAGE 2 SPARK PLUGS
PORT INJECTION
MOTIV REFLEX PLUS
UPGRADED LPFP
ETHANOL SENSOR
3.5BAR T MAP
TURBO SMART DIVERTER VALVE
7.5 INTERCOOLER WITH OUTLET AND INLETS
PROPULSIVE DYNAMICS CLUTCH PACK FOR ZF6HP21X
XHP STG 3



I have been dealing with a misfire issue for the past month, my car is custom tuned from Steve at Wedge. When I try to WOT my car starts to hesitate and misfire consistently however recently this isn't just at WOT anymore its start to do this in fifth gear around 2000 to 2500 rpms.
I have recently replaced the EU5 injectors and coded them accordingly.
I have also replace coils and sparks (Dinan coils and one step colder sparks). However I haven't seen any improvement. The HPFP was replaced about a year ago however I haven't been putting that many miles on the car since I blew the transmission and then had to build it myself with the PPD clutch pack kit with sonaxx zip kit and Recommened lifeguard five fluid. I have done all the work on the car myself turbo, transmission, hpfp, injectors, port injection, etc.

I have attached a couple of logs and well provide upgraded and etc.


05/27/23 RIGHT AFTER TRANSMISSION REBUILD without XHP STG3
Transmission runs fine, previously I only had gears 1-4 and now they all work properly.


https://datazap.me/u/mattbayram/log-...og=0&data=4-19

06/03/2023
AFTER ONE STEP COLDER SPARK PLUGS AND DINAN COIL PACKS
AFTER XHP STG 3 FLASH

https://datazap.me/u/mattbayram/afte...og=0&data=4-19
https://datazap.me/u/mattbayram/log-...og=0&data=4-19


THESE ARE THE CODES DURING THE RUN

Got a couple codes off the car this happened for cyclinders 2,4,6

2775 - Air volume, plausibility: Air volume too low.
2EEO - Combustion misfires, several cylinders: Fuel injection deactivation.
2EF4 - Combustion misfire, cylinder 6: Fuel injection deactivation.
2EFE - Combustion misfires, several cylinders:
Damaging to catalytic converter or damaging exhaust gas.
2F04 - Combustion misfire, cylinder 6: Damaging to catalytic converter or damaging exhaust gas.
- DME shadow (inactive) codes -
2EF7 Verbrennungsaussetzer: Einspritzabschaltung

06/09/2023
https://datazap.me/u/mattbayram/afte...og=0&data=4-19


2EEO - Combustion misfires, several cylinders: Fuel injection deactivation.
2EF4 - Combustion misfire, cylinder 6: Fuel injection deactivation.
2EFE - Combustion misfires, several cylinders:
Damaging to catalytic converter or damaging exhaust gas.
2F04 - Combustion misfire, cylinder 6: Damaging to catalytic converter or damaging exhaust gas.
- DME shadow (inactive) codes -
2EF7 Verbrennungsaussetzer: Einspritzabschaltung



06/11/2023
https://datazap.me/u/mattbayram/afte...og=0&data=4-19

06/19/2023

PUT NEW E85 IN

https://datazap.me/u/mattbayram/afte...og=0&data=4-19

DME active codes - 2EEO - Combustion misfires, several cylinders: Fuel injection deactivation.
2EF4 - Combustion misfire, cylinder 6: Fuel injection deactivation.
2EFE - Combustion misfires, several cylinders:
Damaging to catalytic converter or damaging exhaust gas.
2F04 - Combustion misfire, cylinder 6: Damaging to catalytic converter or damaging exhaust gas.
- DME shadow (inactive) codes -
2EF7 Verbrennungsaussetzer: Einspritzabschaltung


06/24/2023 MOST RECENT LOG AFTER INJECTORS WERE REPLACED

https://datazap.me/u/mattbayram/afte...og=0&data=4-19

When I give it throttle I can feel the car starting to choke up. I also can feel the car choking up when I’m in fifth gear around 2000 to 2500 rpm’s as well. I was thinking it could be port injection but it occurs in lower rpm’s as well. I recently got a code for DME active codes -
29D8 - Intake air temperature - charge air temperature, comparison: Intake air temperature too high.
- DME shadow (inactive) codes -
290A - Intake air temperature sensor: Multiple fault.

I cleared it and it occasionally happens again.


This is the errors I got after it misfires during the log


DME active codes -
2EEO - Combustion misfires, several cylinders: Fuel injection deactivation.
2EED - Combustion misfire, cylinder 4: Fuel injection deactivation.
2EF4 - Combustion misfire, cylinder 6: Fuel injection deactivation.
2EFE - Combustion misfires, several cylinders:
Damaging to catalytic converter or damaging exhaust gas.
2F02 - Combustion misfire, cylinder 4: Damaging to catalytic converter or damaging exhaust gas.
2F04 - Combustion misfire, cylinder 6: Damaging to catalytic converter or damaging exhaust gas.
2F7B - Super-knocking, cylinder 6: Injection switch-off.
2F7C - Super-knocking: Injection switch-off.
- DME shadow (inactive) codes -
2EF7 Verbrennungsaussetzer: Einspritzabschaltung

At this point I can't figure out what to do, could this be due to a spliced wired somewhere, LPFP, HPFP issues? Transmission issues?
Appreciate 0
      06-25-2023, 05:15 AM   #2
__G__
Enlisted Member
4
Rep
37
Posts

Drives: Nil
Join Date: Dec 2022
Location: VIC

iTrader: (0)

Can you revert to OEM or a less aggressive tune? How does the misfire relate to the tune in terms of timing? E.g. misfire only after tuning, or misfire before and after tuning? Tuning obviously pushed the engine harder, so I'd explore options that turn the tune down and see how that affects the misfire.

The error codes don't indicate specific sensor or component faults, so I would look for errors that don't depend on sensors or wiring.

How is compression? Consistent on all cylinders?
Appreciate 0
      06-25-2023, 10:11 AM   #3
Xalithar
Enlisted Member
United_States
12
Rep
40
Posts

Drives: BMW E90 335I X-drive (2011)
Join Date: Dec 2022
Location: Norfok

iTrader: (0)

Garage List
2011 BMW 335i  [0.00]
What are your spark plugs gapped to? Depending on boost levels you should have them gapped between .024 to .022 not the stock gapping. Usually when some thing happens like that the ahkams razor approach works for me.
Appreciate 0
      06-25-2023, 11:01 PM   #4
space_greymatt
Registered
0
Rep
3
Posts

Drives: 2018 X5, 2011 335I XDRIVE,
Join Date: Jun 2023
Location: NJ

iTrader: (0)

So just to close out the thread for anyone else having the same issues

I just compression tested the car all cylinders came back around 165. I just replaced my spark plugs again and gapped them to .20 and that seemed to solve the issue, it could be that I had a bad set of new spark plugs I guess.

Thank you to everyone who replied to the thread.
Appreciate 0
      08-26-2024, 11:22 PM   #5
karun
Registered
0
Rep
3
Posts

Drives: 2011 335xi (N55) coupe
Join Date: Aug 2024
Location: canada

iTrader: (0)

Hi i have a 2011 335xi coupe n55 with these mods
-Vrsf charge pipe
-Vrsf intercooler
-Vrsf catless downpipe
-ngk 2 spark plugs
-bms intake
-mhd stage 2+

Currently i have a cyl 5,6 misfire and this only happens from 2nd gear and up at 5k rpm’s. i changed all 6 spark plugs and that didn’t work. swapped around coil pack for cyl 5, 6 and the misfire still stayed. changed the injector on cyl 5,6 and coded them in and did not work. i have checked over all the wiring for the injector grounds and sensors for my boost connectors but the misfire still stays. Can some one help!!
Appreciate 0
      08-27-2024, 02:44 PM   #6
jmnew911
Enlisted Member
12
Rep
44
Posts

Drives: 335i e93, x3 e83, 328i e90
Join Date: Jan 2020
Location: Tennessee

iTrader: (0)

Garage List
2007 BMW 328i  [0.00]
KARUN,

Did you try gapping the spark plugs as the original poster states? I had an issuing with missing (no codes). Turns out I did not gap my spark plugs when I installed them. I removed them, gapped all plugs to .20 and all issues are gone.
Appreciate 0
      08-28-2024, 11:38 PM   #7
karun
Registered
0
Rep
3
Posts

Drives: 2011 335xi (N55) coupe
Join Date: Aug 2024
Location: canada

iTrader: (0)

at first i didn’t and it was still misfiring but when i checked some forums they said to do so and i did but it still misfires.
Appreciate 0
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 04:35 AM.




e90post
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST