[e90.Alex]

Hey, I have a 2011 328i. I was driving on the highway when my car suddenly stalled. I heard no noises or seen any oil leaks, so I immediately pulled over to start the car again. The car still has power but has no crank; it only turns over for a second when it is left alone for a day or two. I took the battery for a test, and the result came back bad, so I replaced it, but still no luck.

I also changed the oil to see if there was anything odd but everything seemd fine.

Im hoping to narrow the the problem. Below are the test results.

TEST RESULTS

•P0306 Power Train System Cylinder 6

Misfire Detected

•P0306 Cylinder 6 Misfire Detected

•P0491 Secondary Air Injection System (Bank 1)

•P0015 Exhaust Camshaft Position Timing - Over-Retarded (Bank 1)

•P0304 Cylinder 4 Misfire Detected •P0305 Cylinder 5 Misfire Detected •P0303 Cylinder 3 Misfire Detected •P0302 Cylinder 2 Misfire Detected

•P1625 Pedal Position Sensor Potentiometer Supply Channel 2 Electrical

•P1224 Pedal Position Sensor 1 and 2 Circuit Range/Performance

•P10FD VVL-Sensors Circuit Low

•P0123 Throttle/Pedal Position Sensor A Circuit High Input

•P0222 Throttle/Pedal Position Sensor B Circuit Low Input

•P110D Throttle Position Sensor A and B Circut range/ pefromance

[gbalthrop]

Originally Posted by e90.Alex

... 2011 328i [N51]. I was driving on the highway when my car suddenly stalled. I heard no noises or seen any oil leaks, so I immediately pulled over to start the car again. The car still has power but has no crank; it only turns over for a second when it is left alone for a day or two... battery...replaced, but still no luck...
•P1625 Pedal Position Sensor Potentiometer Supply Channel 2 Electrical •P1224 Pedal Position Sensor 1 and 2 Circuit Range/Performance
•P10FD VVL-Sensors Circuit Low
•P0123 Throttle/Pedal Position Sensor A Circuit High Input
•P0222 Throttle/Pedal Position Sensor B Circuit Low Input
•P110D Throttle Position Sensor A and B Circuit range/ performance

Welcome to the Forum!
All 6 of the fault codes above may be caused by Lack of Power Supply. That power comes from the DME when KL87 (DME Main Relay) is active. F37 on the JB Fuse Panel under glovebox should have battery voltage when Ignition is ON. ISTA ScreenPrints showing Voltage supply to DME, Accelerator Pedal module Voltage Supply, and ESS Supply, along with F37 Location, are attached to NEXT post.

However, if you have NO Starter Cranking, or it only cranks for one second or less, then you have OTHER issues. So please answer the following:

Questions:
1) Make/Model of any Scan Tool or diagnostic software available?
2) Are there any OTHER Fault Codes in DME (Engine Control Module) Memory, other than listed by you? Ignore any misfire codes.
3) If your Scan Tool/Software can display Freeze Frame Data, please provide that data for each fault above.
4) Can your Tool display Fault Memory of CAS Module? That would provide information related to any "NO Crank" issue.
5) Do you have a multimeter?
6) Do you have AT (Automatic Trans) vs. MT?
7) When you turn on Ignition, (WITHOUT pressing Brake/Clutch) does Instrument Cluster Light? Does Climate Control Panel light & Blower work?
8) If AT, can you shift from Park with Ignition ON & foot on Brake?
9) If so, does Gear Selected appear in lower Instrument Cluster display (P,R,N,D)?
10) Do Brake lights light when brake pedal pressed with Remote Key inserted?

With answers to questions above, we can furnish "Next Steps" which YOU can perform with equipment available. Minimum Requirement: $10 Multimeter.
George

[gbalthrop]

ISTA ScreenPrints related to Prior Post, 2011 328i N51 E90:
George

[gbalthrop]

Here are BMW Fault Code Lookup Fault Info Sheet Links for the 6 fault codes listed in previous codes. NOTE the Service Notes:
https://bmwfault.codes/XMLDiagView?d...E4NTgxNjcwNQ==
https://bmwfault.codes/XMLDiagView?d...E4Njg2OTUwNQ==
https://bmwfault.codes/XMLDiagView?d...E4NTg5NjMwNQ==
https://bmwfault.codes/XMLDiagView?d...E4NjkzOTYwNQ==
https://bmwfault.codes/XMLDiagView?d...E4NjkzOTUwNQ==
https://bmwfault.codes/XMLDiagView?d...E4NTEzMjkwNQ==
George