DSC voltage spikes

E335IA · 07-22-2024, 01:26 AM

Hello guys,

I have an E92 335I. I've been chasing so many things on the car and it's an error after an Error.

First issue with DSC:
Yaw rate sensor connectors were worn out and burned. Fixes that and everything looks good.

Two days later DSC light are back!

Second issue: wheel speed sensor! Fixed. (Voltage too High was first seen)

Third issue:(pain in my A**)

I'm getting a high system voltage for only the DSC Module. It happens very random either City or highway. I'll be cursing and next thing I know my Idrive goes out for a second and then comes back. second time will be instrument cluster and Idrive complete shutdown for a second and everything comes back to life. I pulled out ISTA codes and here is what I have:

005DF7 DSC: System voltage too high
005Е63 DSC: Instrument cluster, interface
00A9AC ULF-SBX-Hi overvoltage (bluetooth)

things I've done to the car recently:
*95 AMP COSTCO AGM battery; Have coded it with NCS expert & dummy to be 90 AGM battery

*New voltage regulator; BOSCH from fcp euro

*Walnut blasting

*index 12 injectors

* dinan coil packs

* YAW Rate Sensor fixed and rewired

* AC Fixed

*OIL change

Troubleshooting:

*checked battery ground. it was loose and I tightened it up
*tested voltage during driving 13.3-13.8 using secret menu
*tested alternator using ISTA
*tested battery during IDLE and revved up to 5K while measuring 13.5/14.2 at the battery.
*checked grounds under hood. all looked good.

I honestly dont know where to look or how to go about this. voltage will go to 15.5-16V when the IDRIVE goes berserk and the cluster. "I wasn't hitting bumps" Sometimes it happens sometimes. its weird and ISTA doesn't tell me much or it tells me replace voltage Regulator but I already did or tells me Ignore it its nothing a " Random error IGNORE". I would really appreciate any help. im just lost in all of this and genuinely dont even know where to look or why is this happening I would really appreciate anything and suggestions. Next im going to get a new ground off eBay with IBS and go from there.

TheEliteAngels · Yesterday, 10:48 AM

Hey, Just came across this post, I actually have the same 3 codes that you have been experiencing. on my case it happened after hitting a hard bump, and looking over everything looks ok. i cleared codes as ISTA states and ignored it. but came right back.

I was wondering if you have figured out yet what was causing the situation??

Any help or suggestion is appreciated. Thanks in advance.

07-22-2024, 01:26 AM	#1
E335IA Registered 0 Rep 0 Posts Drives: BMW 335I E92 Join Date: Jul 2024 Location: California iTrader: (0)	Hello guys, I have an E92 335I. I've been chasing so many things on the car and it's an error after an Error. First issue with DSC: Yaw rate sensor connectors were worn out and burned. Fixes that and everything looks good. Two days later DSC light are back! Second issue: wheel speed sensor! Fixed. (Voltage too High was first seen) Third issue:(pain in my A*) I'm getting a high system voltage for only the DSC Module. It happens very random either City or highway. I'll be cursing and next thing I know my Idrive goes out for a second and then comes back. second time will be instrument cluster and Idrive complete shutdown for a second and everything comes back to life. I pulled out ISTA codes and here is what I have: 005DF7 DSC: System voltage too high 005Е63 DSC: Instrument cluster, interface 00A9AC ULF-SBX-Hi overvoltage (bluetooth) things I've done to the car recently: 95 AMP COSTCO AGM battery; Have coded it with NCS expert & dummy to be 90 AGM battery New voltage regulator; BOSCH from fcp euro Walnut blasting index 12 injectors dinan coil packs * YAW Rate Sensor fixed and rewired * AC Fixed OIL change Troubleshooting: checked battery ground. it was loose and I tightened it up tested voltage during driving 13.3-13.8 using secret menu tested alternator using ISTA tested battery during IDLE and revved up to 5K while measuring 13.5/14.2 at the battery. checked grounds under hood. all looked good. I honestly dont know where to look or how to go about this. voltage will go to 15.5-16V when the IDRIVE goes berserk and the cluster. "I wasn't hitting bumps" Sometimes it happens sometimes. its weird and ISTA doesn't tell me much or it tells me replace voltage Regulator but I already did or tells me Ignore it its nothing a " Random error IGNORE". I would really appreciate any help. im just lost in all of this and genuinely dont even know where to look or why is this happening I would really appreciate anything and suggestions. Next im going to get a new ground off eBay with IBS and go from there. Attached Images
	Appreciate 0 Tweet Quote

Yesterday, 10:48 AM	#2
TheEliteAngels Registered 0 Rep 0 Posts Drives: BMW E92 335XI AND 328XI Join Date: Nov 2024 Location: Florida iTrader: (0)	Same thing is happening to my 328i Hey, Just came across this post, I actually have the same 3 codes that you have been experiencing. on my case it happened after hitting a hard bump, and looking over everything looks ok. i cleared codes as ISTA states and ignored it. but came right back. I was wondering if you have figured out yet what was causing the situation?? Any help or suggestion is appreciated. Thanks in advance.
	Appreciate 0 Quote