O2 sim in procede doesnt work for me

mkiv · 06-16-2010, 03:34 PM

FIXED.

jpsimon · 06-16-2010, 03:37 PM

These don't appear to have anything to do with the o2 sim, did you try driving around to see if they just go away?

2F4C
2F4A

Quote:

2F4C:
2F4C Message EWS-DME digital motor electronics electronic vehicle immobilization-digital motor electronics failure
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Signal or value below threshold

2F4A:
2F4A Interface EWS-DME electronic vehicle immobilization / digital motor electronics
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Signal or value below threshold

mkiv · 06-16-2010, 03:45 PM

yes i drove the car for like 20kms, the ses light is steady there.
also i scaned the car via BT cable as well, i got catalytic conversion codes.
should i go lower than 25%?? seems too low?

mkiv · 06-16-2010, 04:43 PM

update: tried seting from 50% up to 90%, always got 2C9D Lambda Probe heating in front of catalytic converter 2, input singnal
and tried from 50% down to 5%, always got same 2C9D code.....
wow...

mkiv · 06-16-2010, 05:04 PM

also tried to reset lambda via BT, no help.

cn555ic · 06-16-2010, 05:19 PM

Are you sure your 02 sensors were installed back onto the car correctly?? There should not be a problem with Procede 02 modifier..

mkiv · 06-16-2010, 05:24 PM

im going to my tech's house to check the wiring on o2 sensors in an hr.
any inputs b4 i go?

mkiv · 06-16-2010, 10:53 PM

just got back home, turned out its an damaged o2 sensor. repleaced and working now.

OpenFlash · 06-16-2010, 11:13 PM

Quote:

Originally Posted by mkiv

just got back home, turned out its an damaged o2 sensor. repleaced and working now.

06-16-2010, 03:34 PM	#1
mkiv 2JZ 64 Rep 819 Posts Drives: 16 G500 Join Date: Nov 2008 Location: 温哥华Vancouver iTrader: (6)	O2 sim in procede doesnt work for me FIXED. __________________ E92 335i Fully Loaded \| Procede Rev2 \| ETS FMIC \| AR Catless DP \| AFE DCI \| AA BOV \| KW V2 \| iForged Essen \| VRS CF Trunk \| M-Tech Sideskirts \| M-Tech Rear \| Ericsson Front GONE! Last edited by mkiv; 06-16-2010 at 10:53 PM..
	Appreciate 0 Tweet Quote

06-16-2010, 03:45 PM	#3
mkiv 2JZ 64 Rep 819 Posts Drives: 16 G500 Join Date: Nov 2008 Location: 温哥华Vancouver iTrader: (6)	yes i drove the car for like 20kms, the ses light is steady there. also i scaned the car via BT cable as well, i got catalytic conversion codes. should i go lower than 25%?? seems too low? __________________ E92 335i Fully Loaded \| Procede Rev2 \| ETS FMIC \| AR Catless DP \| AFE DCI \| AA BOV \| KW V2 \| iForged Essen \| VRS CF Trunk \| M-Tech Sideskirts \| M-Tech Rear \| Ericsson Front GONE!
	Appreciate 0 Quote

06-16-2010, 04:43 PM	#4
mkiv 2JZ 64 Rep 819 Posts Drives: 16 G500 Join Date: Nov 2008 Location: 温哥华Vancouver iTrader: (6)	update: tried seting from 50% up to 90%, always got 2C9D Lambda Probe heating in front of catalytic converter 2, input singnal and tried from 50% down to 5%, always got same 2C9D code..... wow... __________________ E92 335i Fully Loaded \| Procede Rev2 \| ETS FMIC \| AR Catless DP \| AFE DCI \| AA BOV \| KW V2 \| iForged Essen \| VRS CF Trunk \| M-Tech Sideskirts \| M-Tech Rear \| Ericsson Front GONE!
	Appreciate 0 Quote

06-16-2010, 05:04 PM	#5
mkiv 2JZ 64 Rep 819 Posts Drives: 16 G500 Join Date: Nov 2008 Location: 温哥华Vancouver iTrader: (6)	also tried to reset lambda via BT, no help. __________________ E92 335i Fully Loaded \| Procede Rev2 \| ETS FMIC \| AR Catless DP \| AFE DCI \| AA BOV \| KW V2 \| iForged Essen \| VRS CF Trunk \| M-Tech Sideskirts \| M-Tech Rear \| Ericsson Front GONE!
	Appreciate 0 Quote

06-16-2010, 05:19 PM	#6
cn555ic 460 Rep 18,331 Posts Drives: 335i Join Date: Jun 2007 Location: US iTrader: (6)	Are you sure your 02 sensors were installed back onto the car correctly?? There should not be a problem with Procede 02 modifier..
	Appreciate 0 Quote

06-16-2010, 05:24 PM	#7
mkiv 2JZ 64 Rep 819 Posts Drives: 16 G500 Join Date: Nov 2008 Location: 温哥华Vancouver iTrader: (6)	im going to my tech's house to check the wiring on o2 sensors in an hr. any inputs b4 i go? __________________ E92 335i Fully Loaded \| Procede Rev2 \| ETS FMIC \| AR Catless DP \| AFE DCI \| AA BOV \| KW V2 \| iForged Essen \| VRS CF Trunk \| M-Tech Sideskirts \| M-Tech Rear \| Ericsson Front GONE!
	Appreciate 0 Quote

06-16-2010, 10:53 PM	#8
mkiv 2JZ 64 Rep 819 Posts Drives: 16 G500 Join Date: Nov 2008 Location: 温哥华Vancouver iTrader: (6)	just got back home, turned out its an damaged o2 sensor. repleaced and working now. __________________ E92 335i Fully Loaded \| Procede Rev2 \| ETS FMIC \| AR Catless DP \| AFE DCI \| AA BOV \| KW V2 \| iForged Essen \| VRS CF Trunk \| M-Tech Sideskirts \| M-Tech Rear \| Ericsson Front GONE!
	Appreciate 0 Quote