Procede V4 installation

Superman0150 · 07-16-2010, 01:39 PM

Hey guys, I'm new to modding and all that stuff and I was recently stuck in deciding between the JB3 and V4 for my 335i but I've made my decision. I think I'm going to go with the V4 because the number one most important issue for me was making sure the dealer could not find out. Couldn't take chances and the V4 is good with the code clearing. Now I've seen a few videos on installing the V4 and it seems pretty simple, but still seeing as its my first time, I dont want to mess up. I live in South Florida and planning on installing the product around August 10th. If anyone would like to help with the installation it would be greatly appreciated! Thank you very much!

etai2009@gmail.com

shoes · 07-16-2010, 01:47 PM

I would suggest you learn how to do it yourself. That way when the time comes to remove it, you know how.
Having some help is fine, but don't just pay them to do it... just my opinion of course.

Check out the regional sections for people in your area:
http://www.e90post.com/forums/forumdisplay.php?f=19

Good luck!

OpenFlash · 07-16-2010, 01:48 PM

OP- You should have any problem finding people in your area with Procedes. In fact, even those who have installed a jb3 pnp will be able to help as installation is the same. But like shoes said, the installation is simple and just about anyone can do it. I can do a full install in less than 3 minutes which shows that there really isn't much actual "work" involve. Just take your time and follow the video.

Shiv

Superman0150 · 07-16-2010, 02:22 PM

Quote:

Originally Posted by shoes

I would suggest you learn how to do it yourself. That way when the time comes to remove it, you know how.
Having some help is fine, but don't just pay them to do it... just my opinion of course.

Check out the regional sections for people in your area:
http://www.e90post.com/forums/forumdisplay.php?f=19

Good luck!

yeah yeah! thats for sure the smartest thing to do! What I would like is for someone to install it in front of me and would explain to me everything. I would even like to install it myself and have him behind me coaching haha. But the problem with the vid is, if i get confused im stuck :\ cant have that! haha but thank you!

Sal Collaziano · 07-16-2010, 08:32 PM

3 minutes.

What people like the original poster and I want to know is how long it takes you to install the Proceed from the time you open the hood to the time you close it. It takes me about 3 minutes to plug everything in once the ECU is opened. But it takes me a while to get to the ECU and then seal everything back up.

In any event, I'm not mechanically inclined AT ALL and these tunes are very easy to install. Just set aside a few hours your first time and go slow.

Quote:

Originally Posted by shiv@vishnu

OP- You should have any problem finding people in your area with Procedes. In fact, even those who have installed a jb3 pnp will be able to help as installation is the same. But like shoes said, the installation is simple and just about anyone can do it. I can do a full install in less than 3 minutes which shows that there really isn't much actual "work" involve. Just take your time and follow the video.

Shiv

OpenFlash · 07-16-2010, 09:43 PM

Quote:

Originally Posted by Sal Collaziano

3 minutes.

What people like the original poster and I want to know is how long it takes you to install the Proceed from the time you open the hood to the time you close it. It takes me about 3 minutes to plug everything in once the ECU is opened. But it takes me a while to get to the ECU and then seal everything back up.

In any event, I'm not mechanically inclined AT ALL and these tunes are very easy to install. Just set aside a few hours your first time and go slow.

That 3 minute time is from hood closed to hood closed. But, to be fair, I had a battery operated 8mm socket. I think the video is posted somewhere. lol

Shiv

yandy · 07-17-2010, 12:08 AM

you have email

OpenFlash · 07-17-2010, 12:13 AM

Thanks for helping him out Yandy

Sal Collaziano · 07-17-2010, 09:35 AM

Okay. I need to get a battery operated socket then.

In that case, it would probably take me 20 minutes. Either way, it's pretty easy. I didn't think I'd be able to do it without breaking things, but I manage.

Quote:

Originally Posted by shiv@vishnu

That 3 minute time is from hood closed to hood closed. But, to be fair, I had a battery operated 8mm socket. I think the video is posted somewhere. lol

Shiv

Jeffman · 07-24-2010, 02:02 PM

Quote:

Originally Posted by shiv@vishnu

That 3 minute time is from hood closed to hood closed. But, to be fair, I had a battery operated 8mm socket. I think the video is posted somewhere. lol

Shiv

Shiv - I viewed the install video but still got confused between all of the connectors and wires.

I'm afraid I'll make a wrong connection and ruin the car.

I'm looking for pdf file that has plenty of detailed pictures but haven't been able to find one on your website. Can you please post one? I want to be absolutely sure I can do this myself before making the investment. Thanks.

garfi · 08-05-2010, 11:34 AM

Guys I'm having trouble with installation.
I installed all sockets with watching install video.
But one cable (it is thin, black wire and has red female plug on the top) left. There is no information about this cable on the video. I know that I skiped the map switching section on the video, I taped its cable. But one cable left and like I said there is no information about this cable on the video.

Please help.

What is it? Where I need to plug it?

Thanks

Sorry for my english

lndnny · 08-05-2010, 12:20 PM

Quote:

Originally Posted by garfi

Guys I'm having trouble with installation.
I installed all sockets with watching install video.
But one cable (it is thin, black wire and has red female plug on the top) left. There is no information about this cable on the video. I know that I skiped the map switching section on the video, I taped its cable. But one cable left and like I said there is no information about this cable on the video.

Please help.

What is it? Where I need to plug it?

Thanks

Sorry for my english

It's for progressive methanol, no need to plug it in on a simple install.

OpenFlash · 08-05-2010, 12:28 PM

Quote:

Originally Posted by lndnny

It's for progressive methanol, no need to plug it in on a simple install.

+1. Same goes for the that little 3-wire black connector. That's for nitrous mapswitching.

So in a basic install, you have those two connectors not connected to anything.

Shiv

fisherbln · 08-05-2010, 01:48 PM

Quote:

Originally Posted by shiv@vishnu

That 3 minute time is from hood closed to hood closed. But, to be fair, I had a battery operated 8mm socket. I think the video is posted somewhere. lol

Shiv

I want to see that video!

e93WhiteonRed · 10-27-2010, 12:36 PM

Question for you Shiv.

With all of the in car features like the boost and AF guages in your factory dash, do you have to run a plug into the car to the OBDII port?

lyndon_h · 10-27-2010, 12:48 PM

Quote:

Originally Posted by e93WhiteonRed

Question for you Shiv.

With all of the in car features like the boost and AF guages in your factory dash, do you have to run a plug into the car to the OBDII port?

While the question was not directed at me, I can answer that. You do not have to plug anything into the ODB port to monitor boost, etc. It is all controlled from the procede.

jfawns76 · 10-27-2010, 01:17 PM

Quote:

Originally Posted by fisherbln

I want to see that video!

Me too...video or it didn't happen!

jfawns76 · 11-03-2010, 09:28 PM

Having trouble getting the power wire out. Is there a trick to this?? It's a different connection than on the install video. I've pried the green tab so much it's about to break off and used considerable force but to no avail.

cn555ic · 11-03-2010, 09:30 PM

Quote:

Originally Posted by jfawns76

Having trouble getting the power wire out. Is there a trick to this?? It's a different connection than on the install video. I've pried the green tab so much it's about to break off and used considerable force but to no avail.

You have to extract the wire from the other side of the connector not the one in the pic!

jfawns76 · 11-03-2010, 09:36 PM

Quote:

Originally Posted by cn555ic

You have to extract the wire from the other side of the connector not the one in the pic!

The other side? Do you mean the back side? The opposite of the 2 slot is the 6 slot, & I can't see where where you would be able to extract the wire from there??

pits200 · 11-03-2010, 09:38 PM

Like cn555 said, you need to get access to the other side of the green connector still attached. I did the exact same thing you did then finally realized my error.

It's simple once you get to the other connector.

jfawns76 · 11-03-2010, 09:53 PM

Quote:

Originally Posted by pits200

Like cn555 said, you need to get access to the other side of the green connector still attached. I did the exact same thing you did then finally realized my error.

It's simple once you get to the other connector.

Ahh......got it....duhhhh!

07-16-2010, 01:39 PM	#1
Superman0150 Private 6 Rep 73 Posts Drives: 335i Join Date: Jul 2010 Location: Miami FL iTrader: (0)	Procede V4 installation Hey guys, I'm new to modding and all that stuff and I was recently stuck in deciding between the JB3 and V4 for my 335i but I've made my decision. I think I'm going to go with the V4 because the number one most important issue for me was making sure the dealer could not find out. Couldn't take chances and the V4 is good with the code clearing. Now I've seen a few videos on installing the V4 and it seems pretty simple, but still seeing as its my first time, I dont want to mess up. I live in South Florida and planning on installing the product around August 10th. If anyone would like to help with the installation it would be greatly appreciated! Thank you very much! etai2009@gmail.com
	Appreciate 0 Tweet Quote

07-16-2010, 01:47 PM	#2
shoes Captain 25 Rep 635 Posts Drives: 07 BSM E92 335i Join Date: Sep 2009 Location: Huntington Beach, CA iTrader: (1)	I would suggest you learn how to do it yourself. That way when the time comes to remove it, you know how. Having some help is fine, but don't just pay them to do it... just my opinion of course. Check out the regional sections for people in your area: http://www.e90post.com/forums/forumdisplay.php?f=19 Good luck! __________________
	Appreciate 0 Quote

07-16-2010, 01:48 PM	#3
OpenFlash 1806 Rep 17,960 Posts Drives: A Lot Join Date: Sep 2006 Location: SF Bay, CA iTrader: (0) Garage List 2018 Ducati Panigal ... [0.00] 2016 Mazda CX5 [0.00] 2017 Aprilia Tuono ... [0.00] 2019 BMW M2 Competi ... [0.00] 2015 BMW M5 Competi ... [10.00] 2016 Ducati XDiavel S [0.00] 2016 AMG GT S [0.00] 2011 Ferrari 458 It ... [0.00] 2017 Charger Hellcat [0.00] 2015 KTM Super Duke ... [0.00] 2016 KTM RC390 [0.00]	OP- You should have any problem finding people in your area with Procedes. In fact, even those who have installed a jb3 pnp will be able to help as installation is the same. But like shoes said, the installation is simple and just about anyone can do it. I can do a full install in less than 3 minutes which shows that there really isn't much actual "work" involve. Just take your time and follow the video. Shiv
	Appreciate 0 Quote

07-17-2010, 12:08 AM	#7
yandy Lieutenant Colonel 117 Rep 1,971 Posts Drives: 2009 e92 MR "Civic" ///M3 Join Date: Feb 2009 Location: Miami, FL iTrader: (3) Garage List 2009 BMW M3 [0.00]	you have email __________________ \|\| DCT \| ESS Tune \| ACM Test-pipes \| AA Green Filter \| Swift Spec-R Springs \| Stoptech ST-40 F \|\| \|\| My Youtube Channel \|\|
	Appreciate 0 Quote

07-17-2010, 12:13 AM	#8
OpenFlash 1806 Rep 17,960 Posts Drives: A Lot Join Date: Sep 2006 Location: SF Bay, CA iTrader: (0) Garage List 2018 Ducati Panigal ... [0.00] 2016 Mazda CX5 [0.00] 2017 Aprilia Tuono ... [0.00] 2019 BMW M2 Competi ... [0.00] 2015 BMW M5 Competi ... [10.00] 2016 Ducati XDiavel S [0.00] 2016 AMG GT S [0.00] 2011 Ferrari 458 It ... [0.00] 2017 Charger Hellcat [0.00] 2015 KTM Super Duke ... [0.00] 2016 KTM RC390 [0.00]	Thanks for helping him out Yandy
	Appreciate 0 Quote

08-05-2010, 11:34 AM	#11
garfi Private 2 Rep 89 Posts Drives: E93 335i Join Date: Aug 2008 Location: Turkey iTrader: (1)	Guys I'm having trouble with installation. I installed all sockets with watching install video. But one cable (it is thin, black wire and has red female plug on the top) left. There is no information about this cable on the video. I know that I skiped the map switching section on the video, I taped its cable. But one cable left and like I said there is no information about this cable on the video. Please help. What is it? Where I need to plug it? Thanks Sorry for my english
	Appreciate 0 Quote

10-27-2010, 12:36 PM	#15
e93WhiteonRed Second Lieutenant 19 Rep 267 Posts Drives: 2007 E93 Alpine white with Red Join Date: Jul 2010 Location: Reston, Virginia iTrader: (3) Garage List 2007 335I E93 [0.00]	Question for you Shiv. With all of the in car features like the boost and AF guages in your factory dash, do you have to run a plug into the car to the OBDII port? __________________ 2007 335I E93 sport package Alpine White. BMS DCI, PROcede V4, ACT street clutch, Michelin Pilot Sport A/S Plus and BT Tool. Pending install of Raceland Downpipes.
	Appreciate 0 Quote

11-03-2010, 09:28 PM	#18
jfawns76 Private 4 Rep 59 Posts Drives: e90 335i Join Date: Apr 2010 Location: Atlanta, GA iTrader: (0)	Having trouble getting the power wire out. Is there a trick to this?? It's a different connection than on the install video. I've pried the green tab so much it's about to break off and used considerable force but to no avail. Attached Images
	Appreciate 0 Quote

11-03-2010, 09:38 PM	#21
pits200 Colonel 552 Rep 2,598 Posts Drives: 09 335i X-Drive Black Sapphire Join Date: Mar 2010 Location: Pittsburgh iTrader: (1)	Like cn555 said, you need to get access to the other side of the green connector still attached. I did the exact same thing you did then finally realized my error. It's simple once you get to the other connector.
	Appreciate 0 Quote