Dyno results

E90MTL · 07-06-2010, 08:16 AM

16/10/2010 NEW RUNS - Differences:

Same mods as before - Just new map (Autotune)
Autotune Enabled, Agression=2
And No Octane Enhancer

TQ 431.2 @ 2784 rpm --> 12.88 psi
HP 368.6 @ 5750 rpm --> 13.64 psi

Steady 57 deg F Ambient.
relative Humidity 34%

this is only a screen shot of some of the 25+ runs we did.

2007 E90 335i
6AT
Vishnu Procede V4 non-autotune.
Map 2, 2+
Helix FMIC
AFE DCI
Britalman Exhaust
94 Octane + 2 bottls of NOS octane enhancer for good measure. LOL.

4/6/2010
TQ 396.7 @ 2912 rpm --> 13.34 psi --> 11.92 AFR
HP 365.5 @ 5752 rpm --> 11.48 psi --> 13.69 AFR

Steady 99.9 / 100 deg F Ambient.

So... after a few months of enjoying my tune and some bolt ons... I figured it was time to set a few "baseline" runs, before I tune it more.

I went to Dynodoc - www.dynodoc.ca - Brady Moffat (info@dynodoc.ca). Brady was very friendly and enthusiastic, I would reccomend Him and his shop for all forms of Engine Tunning. (514) 396-9390
6565, ave Durocher
Montreal Quebec H2V3Z4
Canada

lyndon_h · 07-06-2010, 08:47 AM

Nice numbers, especially for the temp. I didn't know that Montreal got so hot!

E90MTL · 07-06-2010, 08:54 AM

we have a wicket heat wave... it's bloody ridiculous.

Irishace · 07-06-2010, 08:59 AM

Good numbers!

zeenon53 · 07-06-2010, 09:28 AM

Very nice. I've never seen a dyno like that before.

luv135i · 07-06-2010, 09:38 AM

Quote:

Originally Posted by zeenon53

Very nice. I've never seen a dyno like that before.

Dynopacks are good...just tend to read a lil high due to not having to turn any rotating mass.

ar design · 07-06-2010, 12:48 PM

Very nice! Time for some methanol and downpipes!

OpenFlash · 07-06-2010, 01:10 PM

Quote:

Originally Posted by luv135i

Dynopacks are good...just tend to read a lil high due to not having to turn any rotating mass.

They tend to read a few % higher than other load bearing dynes (mustang, dyno dynamics, etc. But still lower than Dynojets which are universally regarded as the most optimistic. This is assuming standard calibration of course which is why a stock/valet baseline run is useful. Good results though, good-looking car as well!

But definitely update to the autotuning maps. You will probably find out that you left a lot on the table with the early maps at default settings.

Shiv

E90MTL · 07-06-2010, 04:10 PM

Andrew.... I loved the Helix FMIC I got from you.. too bad I had to sell your catless DP's during winter to make a car payment. all is good now. DP's are still up in the air.. I won't cheap out for the VK's or raceland.. I want AR only... but don't have the spare $$.

Shiv, you just emailed me the link to the autotuning maps... thanks. If i send you the CSV file with the AFR's and PSI.. (didn't Procede data log this time) can you just give it a once over for sanity check. The tuner said it was dumping a lot of fuel.. and running a lot leaner higher up would be much better....

OpenFlash · 07-06-2010, 04:17 PM

Quote:

Originally Posted by E90MTL

Andrew.... I loved the Helix FMIC I got from you.. too bad I had to sell your catless DP's during winter to make a car payment. all is good now. DP's are still up in the air.. I won't cheap out for the VK's or raceland.. I want AR only... but don't have the spare $$.

Shiv, you just emailed me the link to the autotuning maps... thanks. If i send you the CSV file with the AFR's and PSI.. (didn't Procede data log this time) can you just give it a once over for sanity check. The tuner said it was dumping a lot of fuel.. and running a lot leaner higher up would be much better....

Yep..email it over. It's very unlikely that the car was running too rich up top. It should run around 11:1 up top which is on the rich side. But it's certainly not too rich by any means. Maybe the tuner is used to traditional naturally aspirated engines in which case 11:1 is too rich for sure.

Also, in your dyno results, what is the low 250whp run? Valet? Stock?

Shiv

E90MTL · 07-06-2010, 04:58 PM

Shiv,

All info sent to your email. Thank you for your personal dedication to Customer service.

Going beyond standard product support has won me as a lifelong client.

dzenno · 07-06-2010, 05:16 PM

you might be running richer than usual if you have a boost leak...

OpenFlash · 07-06-2010, 05:36 PM

Quote:

Originally Posted by E90MTL

Shiv,

All info sent to your email. Thank you for your personal dedication to Customer service.

Going beyond standard product support has won me as a lifelong client.

No problem. I saw your txt file that had the AFR values. Looks perfectly solid. ~11.5:1 at peak hp. Not too rich by any means.

Shiv

BOOSTED4DR · 07-06-2010, 10:46 PM

nice #s

Fernflex · 07-06-2010, 11:27 PM

Nice numbers, I got simillars numbers but I dont have exhaust and I was running 93 octane.
375whp and 393tq

Jb3 2.0
BMS DCI
Helix Fmic
VK 2.5 catless dp's
Caribbean weather and 100% humidity

And my car feels great you must be happy!

E90MTL · 07-07-2010, 09:38 AM

OK so.. with 3" dp's I should definetly be in the +415tq and ~400HP club with autotuning on and 94octane.

. hmmmm Race gass will be fun

. will I need DV's now?

Quote:

Originally Posted by Fernflex

Nice numbers, I got simillars numbers but I dont have exhaust and I was running 93 octane.
375whp and 393tq

Jb3 2.0
BMS DCI
Helix Fmic
VK 2.5 catless dp's
Caribbean weather and 100% humidity

And my car feels great you must be happy!

kennejp · 07-07-2010, 09:55 PM

With the autotune would you be running more boost? Boost levels seem a little low for your mods?

Fernflex · 07-08-2010, 10:18 AM

You can use your stock dv's but you maybe loosing boost, Dp's helps a lotttt, im removing my 2.5 and installing 3''

E90MTL · 11-03-2010, 02:58 PM

bump - NEW RUNS

DefactoM6 · 11-03-2010, 03:36 PM

So let me get this straight... you basically de-modded, ran current maps and got the same power? If so...nice!

E90MTL · 11-03-2010, 03:39 PM

All I did was update to Autotune maps. And I didn't bother with the octane booster.

dc5_champ88 · 11-04-2010, 02:21 PM

siiick #'s!!

07-06-2010, 08:16 AM	#1
E90MTL Private First Class 22 Rep 197 Posts Drives: '07 E90 Join Date: Aug 2009 Location: Montreal iTrader: (1)	Dyno results - 431.2 tq @ 2900 & 368.6 hp 16/10/2010 NEW RUNS - Differences: Same mods as before - Just new map (Autotune) Autotune Enabled, Agression=2 And No Octane Enhancer TQ 431.2 @ 2784 rpm --> 12.88 psi HP 368.6 @ 5750 rpm --> 13.64 psi Steady 57 deg F Ambient. relative Humidity 34% this is only a screen shot of some of the 25+ runs we did. 2007 E90 335i 6AT Vishnu Procede V4 non-autotune. Map 2, 2+ Helix FMIC AFE DCI Britalman Exhaust 94 Octane + 2 bottls of NOS octane enhancer for good measure. LOL. 4/6/2010 TQ 396.7 @ 2912 rpm --> 13.34 psi --> 11.92 AFR HP 365.5 @ 5752 rpm --> 11.48 psi --> 13.69 AFR Steady 99.9 / 100 deg F Ambient. So... after a few months of enjoying my tune and some bolt ons... I figured it was time to set a few "baseline" runs, before I tune it more. I went to Dynodoc - www.dynodoc.ca - Brady Moffat (info@dynodoc.ca). Brady was very friendly and enthusiastic, I would reccomend Him and his shop for all forms of Engine Tunning. (514) 396-9390 6565, ave Durocher Montreal Quebec H2V3Z4 Canada __________________ E90 2007 335i, AW, 6AT/Step, Proceed V4, AFE CAI, Helix FMIC, Britalman Exhaust, 94oct all the time. Dyno - 433tq @ the wheel (Pump gas and stock DP's) Per vox illic est haud terminus Last edited by E90MTL; 11-03-2010 at 03:40 PM.. Reason: New Runs
	Appreciate 0 Tweet Quote

07-06-2010, 08:47 AM	#2
lyndon_h Lieutenant Colonel 41 Rep 1,917 Posts Drives: e90 Join Date: Jan 2007 Location: Madagascar iTrader: (2)	Nice numbers, especially for the temp. I didn't know that Montreal got so hot!
	Appreciate 0 Quote

07-06-2010, 08:54 AM	#3
E90MTL Private First Class 22 Rep 197 Posts Drives: '07 E90 Join Date: Aug 2009 Location: Montreal iTrader: (1)	we have a wicket heat wave... it's bloody ridiculous. __________________ E90 2007 335i, AW, 6AT/Step, Proceed V4, AFE CAI, Helix FMIC, Britalman Exhaust, 94oct all the time. Dyno - 433tq @ the wheel (Pump gas and stock DP's) Per vox illic est haud terminus
	Appreciate 0 Quote

07-06-2010, 08:59 AM	#4
Irishace ElevenPointFive 334 Rep 2,449 Posts Drives: E90 335 Join Date: Oct 2009 Location: Toronto iTrader: (1)	Good numbers! __________________ 2008 E90 335xi - N54 Daily Driver MHD Stage 2+ ~ CPE DPs ~ BMS Intake ~ AMS FMIC
	Appreciate 0 Quote

07-06-2010, 09:28 AM	#5
zeenon53 Major 44 Rep 1,155 Posts Drives: BMW Join Date: Apr 2010 Location: obx iTrader: (3)	Very nice. I've never seen a dyno like that before.
	Appreciate 0 Quote

07-06-2010, 12:48 PM	#7
ar design 302 Rep 4,408 Posts Drives: 04 M3 Join Date: Jan 2008 Location: Denver, CO iTrader: (9)	Very nice! Time for some methanol and downpipes!
	Appreciate 0 Quote

07-06-2010, 04:10 PM	#9
E90MTL Private First Class 22 Rep 197 Posts Drives: '07 E90 Join Date: Aug 2009 Location: Montreal iTrader: (1)	Andrew.... I loved the Helix FMIC I got from you.. too bad I had to sell your catless DP's during winter to make a car payment. all is good now. DP's are still up in the air.. I won't cheap out for the VK's or raceland.. I want AR only... but don't have the spare $$. Shiv, you just emailed me the link to the autotuning maps... thanks. If i send you the CSV file with the AFR's and PSI.. (didn't Procede data log this time) can you just give it a once over for sanity check. The tuner said it was dumping a lot of fuel.. and running a lot leaner higher up would be much better.... __________________ E90 2007 335i, AW, 6AT/Step, Proceed V4, AFE CAI, Helix FMIC, Britalman Exhaust, 94oct all the time. Dyno - 433tq @ the wheel (Pump gas and stock DP's) Per vox illic est haud terminus
	Appreciate 0 Quote

07-06-2010, 04:58 PM	#11
E90MTL Private First Class 22 Rep 197 Posts Drives: '07 E90 Join Date: Aug 2009 Location: Montreal iTrader: (1)	Shiv, All info sent to your email. Thank you for your personal dedication to Customer service. Going beyond standard product support has won me as a lifelong client. __________________ E90 2007 335i, AW, 6AT/Step, Proceed V4, AFE CAI, Helix FMIC, Britalman Exhaust, 94oct all the time. Dyno - 433tq @ the wheel (Pump gas and stock DP's) Per vox illic est haud terminus
	Appreciate 0 Quote

07-06-2010, 05:16 PM	#12
dzenno Banned 287 Rep 5,876 Posts Drives: Join Date: Feb 2006 iTrader: (1)	you might be running richer than usual if you have a boost leak...
	Appreciate 0 Quote

07-06-2010, 10:46 PM	#14
BOOSTED4DR Captain 31 Rep 932 Posts Drives: 07 335i Join Date: Oct 2009 Location: BK,NYC iTrader: (6)	nice #s __________________
	Appreciate 0 Quote

07-06-2010, 11:27 PM	#15
Fernflex First Lieutenant 49 Rep 334 Posts Drives: E92 Crimson Red 335i Join Date: Oct 2009 Location: Guaynabo iTrader: (9)	Nice numbers, I got simillars numbers but I dont have exhaust and I was running 93 octane. 375whp and 393tq Jb3 2.0 BMS DCI Helix Fmic VK 2.5 catless dp's Caribbean weather and 100% humidity And my car feels great you must be happy! __________________ R56 Cooper S E92 335i E30 332is Burger Tuning, Evolution Racewerks and VRFS in Puerto Rico...
	Appreciate 0 Quote

07-07-2010, 09:55 PM	#17
kennejp First Lieutenant 42 Rep 348 Posts Drives: 335i Join Date: Nov 2009 Location: TN iTrader: (2)	With the autotune would you be running more boost? Boost levels seem a little low for your mods?
	Appreciate 0 Quote

07-08-2010, 10:18 AM	#18
Fernflex First Lieutenant 49 Rep 334 Posts Drives: E92 Crimson Red 335i Join Date: Oct 2009 Location: Guaynabo iTrader: (9)	You can use your stock dv's but you maybe loosing boost, Dp's helps a lotttt, im removing my 2.5 and installing 3'' __________________ R56 Cooper S E92 335i E30 332is Burger Tuning, Evolution Racewerks and VRFS in Puerto Rico...
	Appreciate 0 Quote

11-03-2010, 02:58 PM	#19
E90MTL Private First Class 22 Rep 197 Posts Drives: '07 E90 Join Date: Aug 2009 Location: Montreal iTrader: (1)	bump - NEW RUNS __________________ E90 2007 335i, AW, 6AT/Step, Proceed V4, AFE CAI, Helix FMIC, Britalman Exhaust, 94oct all the time. Dyno - 433tq @ the wheel (Pump gas and stock DP's) Per vox illic est haud terminus
	Appreciate 0 Quote

11-03-2010, 03:36 PM	#20
DefactoM6 Sees the world the way it could be 49 Rep 761 Posts Drives: '88 M6, '02 Z8, '09 E92 335i Join Date: May 2010 Location: CT iTrader: (11)	So let me get this straight... you basically de-modded, ran current maps and got the same power? If so...nice! __________________
	Appreciate 0 Quote

11-03-2010, 03:39 PM	#21
E90MTL Private First Class 22 Rep 197 Posts Drives: '07 E90 Join Date: Aug 2009 Location: Montreal iTrader: (1)	All I did was update to Autotune maps. And I didn't bother with the octane booster. __________________ E90 2007 335i, AW, 6AT/Step, Proceed V4, AFE CAI, Helix FMIC, Britalman Exhaust, 94oct all the time. Dyno - 433tq @ the wheel (Pump gas and stock DP's) Per vox illic est haud terminus
	Appreciate 0 Quote

11-04-2010, 02:21 PM	#22
dc5_champ88 Captain 24 Rep 666 Posts Drives: 2007 BMW 335i Join Date: Oct 2010 Location: Maryland iTrader: (5) Garage List 2007 BMW 335i [0.00]	siiick #'s!!
	Appreciate 0 Quote