Removing DP Fix from Jb3

Dr. G · 11-19-2010, 05:14 PM

I have a jb3 with the DP Fix wired into the jb3 parts.

Could I just pull out the wires for the DP Fix? What is the best way to go about this without downpipes yet.

Also anyone know which verion DP fix this is... pics attached.

And the Jb3 is 2.0 gen 3 correct?

Forcefed3 · 11-19-2010, 05:42 PM

Are you going to sell it?

Dr. G · 11-19-2010, 06:04 PM

Well, I wanted to install the jb3 this weekend and I'm not sure if I need to remove the DP Fix.

If I don't I might just keep the DP fix for later, if I remove it I will probably sell the DP Fix as I won't need it until winter is over.

Mike@N54Tuning.com · 11-19-2010, 06:08 PM

Quote:

Originally Posted by Dr. G

Well, I wanted to install the jb3 this weekend and I'm not sure if I need to remove the DP Fix.

If I don't I might just keep the DP fix for later, if I remove it I will probably sell the DP Fix as I won't need it until winter is over.

You still have the 3 small wires that the DP fix replaced, correct? Looks like its version2, the no adjustable one.

Mike

Dr. G · 11-19-2010, 06:13 PM

Ummm no, I don't have the 3 wires that it replaced... is that bad? lol

BOOSTED4DR · 11-19-2010, 06:43 PM

If it doesnt effect it leave it not sure ask mike, but if it does just extend the wires then cut but label them or get a small plug then splice it that way if you install DP's later on it will be an easy plug and play. So you dont have to take apart again.

Dr. G · 11-19-2010, 08:09 PM

So according to the above advice 2 possible scenarios.

1) Install the jb3 as it is and:
a) Don't connect the DP Fix Part
b) Connect the DP Fix Part

2) Cut out the DP Fix part and just tape together the wires after

Any feedback available on these options?

Forcefed3 · 11-19-2010, 08:51 PM

You can install it with the DP fix equipped. Or so I have read on n54tech

RaymondNguyen · 11-19-2010, 09:28 PM

Just take 3 wires from spots not used from the jb3 harness. Look where OEM wires are not connected,now you have 3 small wires ,and now take off the dp fix wires and replace them with 3 small wires..i just did the same thing a week ago

Mike@N54Tuning.com · 11-19-2010, 11:09 PM

Quote:

Originally Posted by RaymondNguyen

Just take 3 wires from spots not used from the jb3 harness. Look where OEM wires are not connected,now you have 3 small wires ,and now take off the dp fix wires and replace them with 3 small wires..i just did the same thing a week ago

+1

Mike

Dr. G · 11-20-2010, 04:18 PM

Okay so I'm not sure if I understood correctly, but this is my interpretation.

Remove the 3 DP Fix wires from the Jb3 plug, then find 3 OEM wires that aren't plugged in anywhere and take those out and put them into the jb3 plug:S ?

Sorry, but I've never done any kind of technical stuff on my own so I'm still pretty technically challenged. Slowly learning though, planning to do all mods by myself to learn

11-19-2010, 05:14 PM	#1
Dr. G Major General 288 Rep 5,064 Posts Drives: Black e92 335i Join Date: Apr 2010 Location: Brampton, Ontario iTrader: (32) Garage List e92 BMW 335i [8.84]	Removing DP Fix from Jb3 I have a jb3 with the DP Fix wired into the jb3 parts. Could I just pull out the wires for the DP Fix? What is the best way to go about this without downpipes yet. Also anyone know which verion DP fix this is... pics attached. And the Jb3 is 2.0 gen 3 correct? Attached Images
	Appreciate 0 Tweet Quote

11-19-2010, 05:42 PM	#2
Forcefed3 Banned 131 Rep 4,732 Posts Drives: 2008 335i Join Date: May 2010 Location: South iTrader: (2) Garage List 2008 335i [1.00]	Are you going to sell it?
	Appreciate 0 Quote

11-19-2010, 06:04 PM	#3
Dr. G Major General 288 Rep 5,064 Posts Drives: Black e92 335i Join Date: Apr 2010 Location: Brampton, Ontario iTrader: (32) Garage List e92 BMW 335i [8.84]	Well, I wanted to install the jb3 this weekend and I'm not sure if I need to remove the DP Fix. If I don't I might just keep the DP fix for later, if I remove it I will probably sell the DP Fix as I won't need it until winter is over.
	Appreciate 0 Quote

11-19-2010, 06:13 PM	#5
Dr. G Major General 288 Rep 5,064 Posts Drives: Black e92 335i Join Date: Apr 2010 Location: Brampton, Ontario iTrader: (32) Garage List e92 BMW 335i [8.84]	Ummm no, I don't have the 3 wires that it replaced... is that bad? lol
	Appreciate 0 Quote

11-19-2010, 06:43 PM	#6
BOOSTED4DR Captain 31 Rep 932 Posts Drives: 07 335i Join Date: Oct 2009 Location: BK,NYC iTrader: (6)	If it doesnt effect it leave it not sure ask mike, but if it does just extend the wires then cut but label them or get a small plug then splice it that way if you install DP's later on it will be an easy plug and play. So you dont have to take apart again. __________________
	Appreciate 0 Quote

11-19-2010, 08:09 PM	#7
Dr. G Major General 288 Rep 5,064 Posts Drives: Black e92 335i Join Date: Apr 2010 Location: Brampton, Ontario iTrader: (32) Garage List e92 BMW 335i [8.84]	So according to the above advice 2 possible scenarios. 1) Install the jb3 as it is and: a) Don't connect the DP Fix Part b) Connect the DP Fix Part 2) Cut out the DP Fix part and just tape together the wires after Any feedback available on these options?
	Appreciate 0 Quote

11-19-2010, 08:51 PM	#8
Forcefed3 Banned 131 Rep 4,732 Posts Drives: 2008 335i Join Date: May 2010 Location: South iTrader: (2) Garage List 2008 335i [1.00]	You can install it with the DP fix equipped. Or so I have read on n54tech
	Appreciate 0 Quote

11-19-2010, 09:28 PM	#9
RaymondNguyen Private First Class 6 Rep 100 Posts Drives: 335xi 2008 Join Date: May 2010 Location: philadelphia iTrader: (6)	Just take 3 wires from spots not used from the jb3 harness. Look where OEM wires are not connected,now you have 3 small wires ,and now take off the dp fix wires and replace them with 3 small wires..i just did the same thing a week ago
	Appreciate 0 Quote

11-20-2010, 04:18 PM	#11
Dr. G Major General 288 Rep 5,064 Posts Drives: Black e92 335i Join Date: Apr 2010 Location: Brampton, Ontario iTrader: (32) Garage List e92 BMW 335i [8.84]	Okay so I'm not sure if I understood correctly, but this is my interpretation. Remove the 3 DP Fix wires from the Jb3 plug, then find 3 OEM wires that aren't plugged in anywhere and take those out and put them into the jb3 plug:S ? Sorry, but I've never done any kind of technical stuff on my own so I'm still pretty technically challenged. Slowly learning though, planning to do all mods by myself to learn
	Appreciate 0 Quote