AA Speed Delimiter or BMS SLD??

kpxshorty · 01-29-2011, 10:20 PM

kpxshorty · 01-30-2011, 08:03 PM

any recommendation?

M3 Eater · 01-31-2011, 04:53 PM

If you run a juice box or proceed the BMs plugs right into the pnp harness. AA needs a power source that you tAp from a hot wire in the ecu box. Both leave codes when you break the limit on the car. My car is non sport, that's why I got one. If the limit is 155 then leave it alone...
My .02$

kpxshorty · 01-31-2011, 08:19 PM

yea my car is non sport too. can we erase code with BT tool?

blackshan · 02-05-2011, 10:31 AM

Good question! Can that code be cleared if u were to exceed the limit with mod in place?

Quote:

Originally Posted by kpxshorty

yea my car is non sport too. can we erase code with BT tool?

Diggy Diggy · 02-05-2011, 10:48 AM

No.

Quote:

Originally Posted by blackshan

Good question! Can that code be cleared if u were to exceed the limit with mod in place?

BongC36 · 02-07-2011, 11:05 AM

Quote:

Originally Posted by M3 Eater

If you run a juice box or proceed the BMs plugs right into the pnp harness. AA needs a power source that you tAp from a hot wire in the ecu box. Both leave codes when you break the limit on the car. My car is non sport, that's why I got one. If the limit is 155 then leave it alone...
My .02$

I too have a non-sport 335 sedan and have purchased the SLD to increase the 130 MPH speed limiter. A bit OT but the SLD instructions on how to install aren't very clear to me. Since you've already done yours, may I seek help?

Am I supposed to pull out the 2 wires from the gray sub-connector and insert the SLD loom? Also for the large black connector, should I pull out the blue/yellow wire and insert the red wire from the SLD?

BobVader · 02-07-2011, 04:23 PM

Quote:

Originally Posted by Spoolin

No.

Change two new turbo and two new selenoid some week after go at 300 km/h (186mph)....and no problem at dealers.

onefastman · 02-07-2011, 08:13 PM

BMS all the way

blackshan · 02-07-2011, 09:29 PM

No problem at all? Bye the way thats movin!

Quote:

Originally Posted by BobVader

Quote:

Originally Posted by Spoolin

No.

Change two new turbo and two new selenoid some week after go at 300 km/h (186mph)....and no problem at dealers.

01-29-2011, 10:20 PM	#1
kpxshorty Captain 36 Rep 662 Posts Drives: 2008 E90 335i Join Date: May 2007 Location: Torrance iTrader: (7)	AA Speed Delimiter or BMS SLD?? AA Speed Delimiter or BMS SLD??
	Appreciate 0 Tweet Quote

01-30-2011, 08:03 PM	#2
kpxshorty Captain 36 Rep 662 Posts Drives: 2008 E90 335i Join Date: May 2007 Location: Torrance iTrader: (7)	any recommendation?
	Appreciate 0 Quote

01-31-2011, 04:53 PM	#3
M3 Eater Major 36 Rep 1,054 Posts Drives: 335i Sedan Join Date: May 2010 Location: Unknown iTrader: (3) Garage List 2007 335i [0.00]	They are the same If you run a juice box or proceed the BMs plugs right into the pnp harness. AA needs a power source that you tAp from a hot wire in the ecu box. Both leave codes when you break the limit on the car. My car is non sport, that's why I got one. If the limit is 155 then leave it alone... My .02$ __________________ JB4 beta 15 ohms FSB,AEM inline filter/ CM 10, ETS fmic, ER custom made charge pipe,TSW Donnington 18's,Simitumo HTRZ3, Injen DCI, AR DPs, Forge DVs, AA SLD, Koni FSD, ZSP springs.
	Appreciate 0 Quote

01-31-2011, 08:19 PM	#4
kpxshorty Captain 36 Rep 662 Posts Drives: 2008 E90 335i Join Date: May 2007 Location: Torrance iTrader: (7)	yea my car is non sport too. can we erase code with BT tool?
	Appreciate 0 Quote

02-07-2011, 08:13 PM	#9
onefastman Major General 163 Rep 5,689 Posts Drives: 2009 135i 2011 e92m dct Join Date: Sep 2009 Location: Earth iTrader: (15)	BMS all the way __________________ Legal Disclaimer: Anything I or anyone else says about my vehicle on this website(1addicts.com or any affiliated or nonaffiliated sites), pertaining to modifications, is only to gain acceptance from my/our peers, and does not actually represent anything actually existing on my car, and thus, cannot be held against me in any issues, i.e. warranty claims, that may arise.
	Appreciate 0 Quote