[Levanime]

and u might need to flash with expert mode

[Mazen328]

I flashed successfully using expert mode in winkfp and it succeeds but the old firmware remains, it seems winkfp is not writing to the frm, any suggestions?

[Sensible_]

Originally Posted by Mazen318

I flashed successfully using expert mode in winkfp and it succeeds but the old firmware remains, it seems winkfp is not writing to the frm, any suggestions?

Which files did you flash with expert mode??

[Mazen328]

I flashed ZB 9390490, my issue with fog lights still persists, uif is disabled. If I enable it, should the flash succeed?

[Mazen328]

So what zb should I flash to resolve my issue?

[Mazen328]

I pulled the below info from winkfp ecu identification
Bmw part number 9342996
Physical hw number: 9206233

The part nb written on the frm3 is 61359224604

Does the flash change the bmw part nb?
And does the new pulled part numbers indicate that i should flash a different zb number to regain the functionality of the Bixenon AHL?

And yes I'm pulling the VO from CAS

[Mazen328]

My question is when the guy flashed the frm with xprog using an x5 e70 file, does this change the part number of the frm3 making the part nb written on the sticker obsolete?

[808AWD325xi]

[Levanime]

I usually repair EEE from D-Flash so it works right away, no coding needed,
Before, I would just write dump from same type FRM(numbers does not matter) and code it and was good.

It was only one time, when I was beginning this stuff, when I tried to use eee from other type of FRM, and then tried winkfp and coding but could not finally make it work.

If you'll post of label on your FRM, I'll drop u dump to use.

[Mazen328]

this is a pic of my frm3, will try to flash it again with the correct files when you provide them. where do we find the latest ZB # that corresponds to this HW?

Thanks and Regards

[Levanime]

try this one
https://www.dropbox.com/s/abmk6l3q3a...D_AHL.rar?dl=0

dont forget to default code with CAS FA

[Mazen328]

tried to flash ZB 9390490 in NFS but got an error. the same I got in Winkfp. it keeps asking for an old non existent file 9342996. how to bypass this error?

[Mazen328]

How to update in winkfp expert mode without it asking for a previous file? Is there *0da file for Frm3 or only *0pa?

Thanks

[Sensible_]

Originally Posted by Mazen328

How to update in winkfp expert mode without it asking for a previous file? Is there *0da file for Frm3 or only *0pa?

Thanks

Put 0pa in develop folder

[Mazen328]

I managed to flash successfully zb 9390490 in comfort mode by adding the required part nb (9342996) to the hwnr.da2 file to bypass the error but I selected to write UIF.

Now zb nb shows 000000 and bmw part number still shows 9342996.
Winkfp flashed successfully, can I assume I'm running zb 9390490?
And by the way, my issues with fogs and cornering lights did not resolve.

Should I flash the module externally with Xprog using the suggested file?

Thanks

[Sensible_]

Originally Posted by Mazen328

I managed to flash successfully zb 9390490 in comfort mode by adding the required part nb (9342996) to the hwnr.da2 file to bypass the error but I selected to write UIF.

Now zb nb shows 000000 and bmw part number still shows 9342996.
Winkfp flashed successfully, can I assume I'm running zb 9390490?
And by the way, my issues with fogs and cornering lights did not resolve.

Should I flash the module externally with Xprog using the suggested file?

Thanks

Just write the correct eeprom dump for your hardware with xprog. All be ok.

[lazh_dk]

Hi, can anyone help me with files for my FRM3-module, 9240530?
Im trying to change the VIN in WinKFP, but need the files for my module.
Thanks!

[Sensible_]

Originally Posted by lazh_dk

Hi, can anyone help me with files for my FRM3-module, 9240530?
Im trying to change the VIN in WinKFP, but need the files for my module.
Thanks!

If you only need to change VIN then why not use tool32? No need to flash anything.

[Levanime]

Originally Posted by lazh_dk

Hi, can anyone help me with files for my FRM3-module, 9240530?
Im trying to change the VIN in WinKFP, but need the files for my module.
Thanks!

https://www.dropbox.com/s/6udhwfdmof...24595.rar?dl=0

this is the file you need

but as Sensible_ said, for changing VIN tool32 is enough

[Brake_Late]

Originally Posted by Mik325tds

Hooray! Success!
Thank you very much for your advice. Much appreciated!
You were correct, the EEPROM was corrupted (as expected). Xprog even gave me a message towards that (duh). Just clearing it and writing a good dump to it worked fine.

You were also correct that XTAL and XCLKS is not needed. In fact, it is counter productive as after doing that and lifting the XTAL pin, somehow the reset of the security doesn't work anymore. Xprog reports "can't connect to BDM" when selecting that. However, it does communicate fine with chip, just on it's own clock rather than the boards crystal.

It also turned out that the Secure mode of Xprog is not needed. I later selected the normal MC9S12XE mode and it wrote to EEprom and Program Flash just fine. However, my Xprog did give me a lot of problems reading either one without mismatches in the verify stage. Don't know why. But restarting Laptop every now and then helped.

By the way, my FRM is using a MC9S12XEQ384 (Mask 3M25J).
I also repaired a friends FRM which used the same chip. You sure the original post is not a typo?

Thanks again, mate. Cheers!

[BSM000]

Hello .. i gotta Mini Cooper R60 2011 and my FRM3R Module got Dump .. im looking for the wiring and needed files for reviving the module ...
Details :

FRM3 No. : 6135 3456395 - 01
SW : 141030
HW : 07

thanks in advance

Regards

[azcwb]

Hy, I have a mini cooper countryman s 2012 and my frm module not working. Stop after a battery change.
Need some help.
The module instaled at car. R56 high eks [35] 6135 3456395 01 sw 141030 hw07.
Its compatible with R56 high eks szt [38] 6135 3457429 01 sw171530 hw12?

Both modules are frm3r pl3.

If is compatible need coding?

And if someone know the diference for the two models?

Sory bad english.

Thanks.

Edit - I change de modules and the head lights, dont stop flashing, and error light apear at bord computer.
Waiting 14.4v 60a charger for do coding.