[Neutrino45]

yes, the server is suppose run when you start the program. what exactly is the problem you're having?

[lamia2super]

Originally Posted by Neutrino45

yes, the server is suppose run when you start the program. what exactly is the problem you're having?

Alright and the problem I'm having is that I canT connect with the car. When I open the program I don't have those black dots that indicate if I'm connected

[bumere90]

Originally Posted by lamia2super

Alright and the problem I'm having is that I canT connect with the car. When I open the program I don't have those black dots that indicate if I'm connected

Did you install all the drivers correctly?

[lamia2super]

Originally Posted by bumere90

Did you install all the drivers correctly?

Ya I just figured it out...I had changed the wrong port to COM1

[mr_milo]

Originally Posted by Dracon

Here's the list of K words out of the v40 daten files, it's all in German and my German sucks.

However, it states you can only have a maximum of 10 K words in the FA (VO).

Also Nachruestung means Retrofitting which should help out a little bit.

If someone on the board is German, or speaks fluent German and would like to translate this, I'm sure it would be most appreicated.

Here a quick Google Translate which seems mostly correct.

//************************************************ ******************************
/ / K: Service-line supplement (no pusy relevance) (+) A maximum of 10 in the FA
//************************************************ *******************************
/ / NOTE: Because of overlap with KMM no e-and K-words are allowed, starting with "L" or "P"
/ /
K Oneg OHNE_NEIGUNG / / deactivation tilt sensor
K OFIS OHNE_FUNK_IN / / deactivation interior sensor
/ / K OtFL OHNE_TAGLICHT / / without daytime running lights
K MTFL MIT_TAGLICHT / / with daytime running lights
K OSZV OHNE_SEL_ZV / / without selective central locking
K MSZV MIT_SEL_ZV / / with selective central locking
K LOCK VERRIEGELN_AN / / lock 16 km / h on (without headset)
K NLOC VERRIEGELN_AUS / / lock 16 km / h off (without headset)
K FLCN FLC_NORMAL / / automatic headlight control normal-sensitive (sensitivity = Standard)
K FLCS FLC_SEHR_EMPF / / automatic headlight control is very sensitive
/ /
K C107 NACHR_CKM_A107 / / Re-equipment of the mechanical activation. Procedure (CKM_A107) (no activation / opening act. After unlocking with FB / Akt. After unlocking with FB and doors)
K TELDE TELEMATIC_DIS / / disable function for Telematic TCU_MOST
K PVCa AKT_PERS_V_CALL / / activation coupled Personal Voice Calls with Speech Recognition
K K639 NACHRUEST_TCUUS / / SAZK639 / / retrofitting Everest platform for U.S. (SA639)
K K633 BT_AKTIVIERUNG / / retrofitting PREPARATION BUSINESS PHONE (only with SA639)
K K641 NACHRUEST_STDUS / / upgrade kit Universal mobile phone preparation with U.S. Standard (South America and Korea)
K RASK MOST_RING_MASK / / enable bit in the MASK RING
K OSVs OHNE_SVS_LOW / / disable function "low language processing" in MASK / M-ULF
K KSET AUTO_SITZVERST / / Automatic seat adjustment after unlocking FB
K OI11 OHNE_FA_SBR / / disable driver Seatbeltreminder
K OI12 OHNE_BF_SBR / / disable passenger Seatbeltreminder
K GKBF OHNE_BF_GK / / Without Gurtkontakt passenger
K SHSZ SONDERSTANDHEIZ / / heater as OPTIONALS
K OI03 OHNE_SIDEBAG_VL / / disable side airbag, front left
K OI04 OHNE_SIDEBAG_VR / / disable side airbag front right
K ID4P ID_GEBER_4 / / 4 ID-Enter for Passive Access
K Nnice NACHRUEST_NIC / / Re-equipment at customer complaint "clutch judder when starting"
K IHKA KLIMA_HIGH IHKA_NACHR / / With + IHKA in the low variant E87 without FZD necessary, with no air FZD
K SPHZ NACHRUEST_SPHZ / / re-fitting mirror
K NDVD NACHRUEST_DVD / / retrofitting FOND DVD PLAYER
K DBFA DEAKT_BEIF_AIRB / / retrofitting passenger airbag deactivation
K BEEF KEIN_RADIO / / Nachruestoption radio navigation Indianapolis E87 and E90
K KMP3 NACHRUEST_MP3 / / Re-equipment / retrofitting MP3 activation to CCC for cars from 09/05 (veh must at least be flashed on CCC_APP.C08)
/ / K TAIN TANKKLAPP_VER / / (tank flap Indonesia)
K USHD FH_DISASHD_KR / / activation Schiebehubdach with terminal R (PA603/161?)
K CD_WECHSLER IPOD IPOD / IPOD retrofitting CD changer
K œœ œœ / / custom tailgate without unlocking
K ABIG NR_ABBIEGELICHT / / retrofitting cornering yet in ASAP
K DIFI DPARTIKELFILTER / / diesel particulate filter
K MLIB / / Modification for Lebanon because of poor fuel quality
K HFMM / / retrofitting retrofitting E90N46 with HFM-SA858
K KFDM / / retrofitting Flexible diagnostic module
K K302 ALARM / / alarm system retrofitting 0306-0906
K SWUL / / Software Update MuLF
K K638 TEL_PROFESIONEL / / retrofitting Car telephone Professional
K K644 ULF / / retrofitting kit Universal
K KOAB KOLIAB / / Re-equipment dedicated lighting shutdown
K NSWA NR_NSWA / / (project: 000 000 251) Pennsylvenia retrofitting FRMFA
K SPBR NR_SPORTBREMSEN / / retrofitting Sport Brakes
K OSST OHNE_SOFTSTOP / / disable retrofitting SST
K Exra EXTERNES_RADIO KEIN_RADIO / / retrofitting external radio, project no. 000000260, 261
K ZBEP PERF_CONT / / Conversion PL2 conversion of the ZBEH to Perform. Controller, Project no. 000000379
K K640 TELE_VORBE / / retrofit kit Universal (Mute without FZD), project no. 000 000 370
K OSTH OSTH / / retrofitting heater, Project no. 000000347
K Okome Okome / / disable conversion Komfortoeffnen, project no. 000000304
K MKOM MKOM / / Conversion Komfortoeffnen activation, project no. 000000304
K xfrm / / retrofit heater ($ 520 to create space without removing FRM exchange), project no. 000 000 412
K MUEB MUE_BELEUCHTUNG / / LCI tail lights retrofit measure E87N, project no. FZ 000 000 246
K KLED LED_AHM / / retrofitting LED lights for trailers, project no. 000000453
K NAVp NAVI_PORTABLE / / retrofitting Portable Navi, project no. 000000419
K RUZU / / Re-equipment E90/91 M57D30TU2 speed fluctuation, project no. 000 000 474
K NSBK NR_SPIEGELBEIKL / / retrofitting Spiegelbeiklappen, project no. 000000480
K RECA NR_SPORTSITZE / / retrofitting performance sports seats, project no. 000000484
K RECF NR_SPORTS_FAHRE / / Upgrades Performance Sports driver seat only, project no. 49 563
K LINS LIN_BEDIENBLOCK / / retrofitting Sport Performance Seat for LIN Patch mirrors
K TAK1 TCU_E91_AUDKORR / / TCU audio correction E91, project no. 000 000 506
K URLK ALPINA_ERSATZ / / retrofit / replacement part in case MSD80 ALPINA B3, project no. 000 000 504
K effort MUE_BEL_HECK / / retrofitting / upgrading Facelift rear lights, project no. 000000536
K MUEG MUE_BEL_FRONT MUE_BEL_HECK / / retrofit / upgrade facelift front and rear lights, project no. 000000539
K K5DA DEAKT_BEIF_AIRB FZD FZD_E88 FZD_E89 / / off BF-locking, in conjunction with roof-electric module without ISOFIX, project no. 000 000 554
K OBBV ONBREMBELVERANZ / / Auskodieren Bremsbelagverschleissanzeige, project no. 000000557
K ZUOF OHNE_ZUHEIZER / / heater not working, project no. 000000563
K WGAK / / retrofitting / wastegate measure, project no. 000000712
K ASCD ASCD / / ASC (Diesel) scheme N57 W-wheels.
K NPower / / upgrade / performance improvement N54 135i / 335i, project no. 22 761, N55 135i / 335i, NA 190 224
K RNIC DREHZAHL_ANHEB / / upgrade / Anfahrdrehzahlanhebung with clutch judder E89xN47 EU5, project no. 156511 (98161) 190174
K knic / / Conversion KMM / Anfahrdrehzahlanhebung with clutch judder E89xN47 EU3 EU4, project no. 169 745
K Diru / / upgrade / E9x N53 MSD80 jerking, project no. 113 847
K INSANE INSANE / / upgrade / iSpeech One Shot Ireland PN 187 425
K ONSW OHNE_NEBELSW / / retrofit retrofit heater - disable NSW
/ / 187 686 NA
K OSAT OHNE_SAT_BILD / / elimination satellite images in some countries
/ / 190 129 NA
K MUH2 MUE_HECKL_LCI_9 / / conversion for LCI tail lights for retrofitting E92/E93
/ / 190 103 NA
K KDDE N47D20_KDDE / / Re-equipment DDE71 N47D20O0 Performance L2 (originally only KMM)
/ / 190 132 NA
K KDD1 N47D20_KDD1 / / upgrade / E91 v-max diesel performance increase with
/ / 190 151 NA
K KAMP ERSATZ_AMP / / Can Spare-Bus Audio AMP by Low Cost HiFi E89
/ / 190 171 NA
K K3AR HECKTRAEG_NACH / / NA, rear luggage carrier for E84 vehicles between 9.9 and 3.10
/ / 190 183 NA
ONIC K O_DREHZ_ANHEB / / disable Anfahrdrehzahlanhebung NA190231
K KSHD SHD_KOMFORTPOS / / E84 Panaramadach comfort position for vehicles 9.10
/ / 190 218 NA
K KATB / / upgrade / DDE73 data compatibility for SCR catalyst at E90US only for KMM
/ / 190 216 NA
K GTRR / / HO word to correct the Schaltklackerproblem's in the DKG / GS40 in HO
/ / 190 279 NA
/ / K MUS1 / / conversion for LCI headlights retrofit E82/E88 / / NA
K MUH1 MUE_HECKL_LCI_8 / / conversion for LCI tail lights retrofit E82/E88
/ / 190 284
K FHRC FH_HINTEN_CABR / / conversion / rear E89/E93 FH
/ / 190 296 NA
K KEPS / / EPS for Altfahzeuge FSC / Mischverbau
/ / 190323 190324
/ / K AGRI / / inverse EGR valve
/ / NA190306
/ / K KDD2 / / diesel performance package
/ / NA190308
/ / K Mus2 / / conversion for LCI headlights retrofit E92/E93

[jphughan]

Originally Posted by JPSlick

Thx a bunch

Look a few pages back (low 100s) and read the section I posted about the Pin 8 dilemma. It may or may not be relevant to you depending on the car(s) you're interested in coding, but it will help your decision re cables. A lot of people buy their cables from eBay seller Automotive-scan-tools: stores dot ebay dot com/automotive-scan-tools?_trksid=p4340.l2563. She's out of stock but says she'll have more within a week.

EDIT: Check Posts #2294 and #2359. There's some good info between those two posts as well but read those at a minimum.

[Jeff@TopGearSolutions]

Originally Posted by jphughan

Look a few pages back (low 100s) and read the section I posted about the Pin 8 dilemma. It may or may not be relevant to you depending on the car(s) you're interested in coding, but it will help your decision re cables. A lot of people buy their cables from eBay seller Automotive-scan-tools: stores dot ebay dot com/automotive-scan-tools?_trksid=p4340.l2563. She's out of stock but says she'll have more within a week.

EDIT: Check Posts #2294 and #2359. There's some good info between those two posts as well but read those at a minimum.

thanks

My car is Jan 09 build. But I planned on coding others if I could.

[jphughan]

Originally Posted by JPSlick

thanks

My car is Jan 09 build. But I planned on coding others if I could.

Then either K+DCAN cable will work (i.e. Pin 8 connected or disconnected). A cable with it connected will let you code older cars, and a cable with it disconnected will let you code newer cars. Or you can just order the cable with it disconnected and request the adapter that will restore Pin 8 connectivity when needed. I don't know how much the eBay seller I mentioned charges for it, but I'd contact her to find out. She may throw it in for free if you buy a cable from her.

[lamia2super]

New problem. Now when I go to check the airbag status I get an error #13 data transmission to interface disturbed. Can my procede be disrupting the connection?

[matrix76]

Originally Posted by matrix76

Question, has anyone been able to determine all the options for the OBC digital display. I noticed that you can get your engine temperature displayed on the digtal steering wheel but what about the OBC, any other options that can be coded in. Are there any lines of code that can be added? Just throwing this out there, , ,

I posted this back a few pages but I think I threw it in the middle of a busy discussion. I wanted to add if anyone knows what this is for as far as the OBC display is concerned;

BC_DIG_GESCHW_BEI_KL_R
nicht_aktiv

[Jay0101]

So I was able to get my cable functioning over the weekend and get INPA working (still couldn't clear my airbag error,- yet, but that's another story).

When trying NCSExpert today I got the following error at step 40 of the DIY (after selecting e89 (chassis) and CAS;

"ERROR: VIN is faulty COAPI-1060 error in coding description file a_e65cas.ipo"

When I select OK the screen remains greyed out, no info.
Anyone else had this problem?

[E90aL]

Originally Posted by Jay0101

So I was able to get my cable functioning over the weekend and get INPA working (still couldn't clear my airbag error,- yet, but that's another story).

When trying NCSExpert today I got the following error at step 40 of the DIY (after selecting e89 (chassis) and CAS;

"ERROR: VIN is faulty COAPI-1060 error in coding description file a_e65cas.ipo"

When I select OK the screen remains greyed out, no info.
Anyone else had this problem?

i used to get that error. solved the problem by deleting ncs, inpa, ediabas folder from the local disk and extracting them again.

[Showsol2211]

Originally Posted by lamia2super

New problem. Now when I go to check the airbag status I get an error #13 data transmission to interface disturbed. Can my procede be disrupting the connection?

Turn your latency down to 1 for whatever COM you are using.

[VitaminXX]

My Cable is K + D CAN. I downloaded the INPA 5.0.2 and EDIABAS 6.47, followed up the installation instructions to installa the INPA. It seems everything worsks fine. I can check my DME, transmission module and most of the modules. However, I can not check smoe of the modules like remote control and trunk lid module. Evertime I connect to these modules, it shows IFH-0009 error message.

The vendor told me that my cable is K + D CAN and it is able to check all the car including F-serials car, F10. To check F-serials car, the pin 8 has to be removed. So, if I want to check my car, E39, with this cable, I need to have pin 8 installed. The vendor sent me the cable with pin 8 removed, and he also included an adapter, if I want to check my car, I need to use this adapter.

As I connect the cable with the adapter, the battery and ignition shows "OFF" on the INPA main screen, but I can check most of the modules. If I connect the cable to the car without the adapter, the battery and ignition shows "ON", but, I CAN NOT read any modules. Every module I connected, all show IFH-0009 error message. So, the cable with adapter works fine but it does not have battery and ignition feedback and when reading the modules which require to check the battey and ignition fails.

Search for the related solution and found the following thread
http://forums.bimmerforums.com/forum....php?t=1505990

This thread is for VAG cable and it shows using MProg to "fool" the ignition signal. I used this way to change my cable's setting as the thread said.
I changed "Invert RI # and DSR # signals" and changed the all the I/O to the following setting (I did not backup original setting)
#C0 = RXLED
#C1 = TXLED
#C2 = POWERON
#C3 = PWRON
#C4 = SLEEP

After that, I wrote it to the cable EEPROM?? (No sure this)

Test this cable again, and no luck.
Tonight, I will check the cable pin setting but except this, does anyone know what should I do?

Thanks

[lamia2super]

Originally Posted by Showsol2211

Turn your latency down to 1 for whatever COM you are using.

Thank you that worked. now im having some more trouble i tried to code the car and nothing happened. i already had a MAN file when i unziped the file and that MAN file already had the feature i wanted active, but when i went to code the car nothing happen.

is this file supposed to look like this?

[DESI4life10]

Originally Posted by lamia2super

Thank you that worked. now im having some more trouble i tried to code the car and nothing happened. i already had a MAN file when i unziped the file and that MAN file already had the feature i wanted active, but when i went to code the car nothing happen.

is this file supposed to look like this?

Ohh boi....dont use that file. You should only use files that come off you car. You can run into serious issues running another cars .man file.

You need to get a fsw_psw.trc file from your car, find the line you want to change and then save it as a .man file. Once that is completed, use that file to code your car.

[kinimod]

Can I get access to the spreadsheet please? I just sent a request via Google Docs. I'm coming from E60 forum but we'd like to try some coding on my friend's E90.

Btw, 12V (DRL mode) angel rings are very cool on E60 LCI. I'm sure it must be possible on E9x too (at least on facelift models).

[jphughan]

Originally Posted by lamia2super

Thank you that worked. now im having some more trouble i tried to code the car and nothing happened. i already had a MAN file when i unziped the file and that MAN file already had the feature i wanted active, but when i went to code the car nothing happen.

is this file supposed to look like this?

What the guy above me said. Do NOT use another car's TRC or MAN file. The file you screenshotted still has a TRC extension, so that right there is problem #1. Change that extension to .MAN and then try coding again -- but yes, use a TRC file pulled from your own car.

[lamia2super]

Originally Posted by DESI4life10

Ohh boi....dont use that file. You should only use files that come off you car. You can run into serious issues running another cars .man file.

You need to get a fsw_psw.trc file from your car, find the line you want to change and then save it as a .man file. Once that is completed, use that file to code your car.

that picture is my file, but i dont have the BC_DIGITAL_V code anywhere in their

does it matter that my car is a e92? if yes is their an upgraded version? Ive followed the video and instructions and nothing

[jphughan]

Originally Posted by lamia2super

that picture is my file, but i dont have the BC_DIGITAL_V code anywhere in their

does it matter that my car is a e92? if yes is their an upgraded version? Ive followed the video and instructions and nothing

Did you grab the KOMBI module? That's where that code lives. If you did and you still don't see it, make sure you have the latest daten for your car, available at www dot mediafire dot com/?309po0avte77vv1.

[lamia2super]

i got it! i noticed the instruction are different from the video and when i followed the video was able to do it. i read the wrong codes....i was reading CAS like the instructions tell you but i was supposed to read KOMBI and when i read that it worked

[lamia2super]

is their an ultimate spread sheet? can someone give me the link or send it to me? please