[1QuikWS6]

After you run a Consistency Check, you need to create a profile that you use from then on to write to the car called a .man file

In NCSExpert:

• File > Load profile > Expertmode > OK
• File > edit profile (Password is 'repxet')
• Select 'car-keymemory' (check all 3 boxes) > OK
• Select 'Consistency Check' (should say 'OK') > OK
• Select 'FSW/PSW' ('CVT' selected + both bottom check boxes) > OK
• Select 'Consistency Check' (should say 'OK') > OK

Then create the .man file:

• File > save profile as > (Enter 'Filename' CSEXPER\PFL\xxxx.PFL) > OK

xxxx = 4 digit name of your choosing, not same as what is currently in file name

• File > edit profile (Password is 'repxet') > profile info > set profile name = 'FSW PSW MAN'

You need to load this profile from now on EVERY time you enter NCSExpert to code


After that is done, to code:

Start NCSExpert

• File > > load profile > 'FSW PSW MAN' (will load what you just created above)
• F1 > F3 > E89 > select 'CAS'
• F6 (or back)
• F4 (Process ECU)> select module you want to code, for Windows Up it will be 'CAS' > OK > 'Read ECU'

This will create a FSW_PSW.TRC file for ONLY the module you selected

Close the screen that comes up with all the chinese writing

• Go to Work Folder
• Open FSW_PSW.TRC file with Notepad
• File > save as all > 'FSW_PSW.MAN'

The FSW PSW MAN profile that you just created earlier will use this FSW_PSW.MAN file & this is where you will make your changes

• Open file FSW_PSW.MAN (you should see all the code lines for the module)
• Find 'KOMFORTSCHLIESSUNG_FB' (for windows up thru key fob) -or- 'KOMFORTSCHLIESSUNG_PA' (for windows up thru comfort access) > change to 'aktiv'
• File > save
• Go back to NCS and select F5
• Select 'coapiReadSgGETFSWPSW' > OK (reads all the values including the one you just changed)
• At next screen > OK (should then say 'basic function perfect ended') > OK
• Select F2 (job)
• Select 'SG_CODIEREN > OK
• Select F3 (to execute job)

screen will gray out then you should see 'coding ended' message. Test windows to see if they work

[lamia2super]

^do you have to create a man file each time you read a new car? i was getting a pws_fault 392 code when i tried to code a e71

[discoboy1]

Hi

I was able to connect INPA, and backup my car.
The strange thing is BC_Digital_V was already set to aktiv...
How can this be??? I am not able to see this feature on the dashboard..

LM_ALIVE
aktiv
BC_DIGITAL_V
aktiv
BC_DIGITAL_V_KORREKTUR
aktiv
ZGM_ALIVE_ZAEHLER
aktiv
TNK_LITER_RECHTS
wert_07
TNK_LITER_LINKS

[1QuikWS6]

Yes, I saw the very same thing when I went thru the backup portion of my E92 - it was showing as aktiv - but obviously it wasn't. Why it shows up that way is beyond me

It might be that when you are reading the entire car - it shows up because it IS a possible option available to turn on or off for your car - doesn't mean it IS turned ON, just means it's available to change...

You still have to go to the appropriate module KOMBI, and go thru the coding of that module seperately. Once you get in, read and look at the KOMBI values, you will see that the BC_Digital is listed as non-aktiv

[discoboy1]

Originally Posted by 1QuikWS6

Yes, I saw the very same thing when I went thru the backup portion of my E92 - it was showing as aktiv - but obviously it wasn't. Why it shows up that way is beyond me

It might be that when you are reading the entire car - it shows up because it IS a possible option available to turn on or off for your car - doesn't mean it IS turned ON, just means it's available to change...

You still have to go to the appropriate module KOMBI, and go thru the coding of that module seperately. Once you get in, read and look at the KOMBI values, you will see that the BC_Digital is listed as non-aktiv

Thanks! I will check the module

[vtnard]

Originally Posted by lamia2super

^do you have to create a man file each time you read a new car? i was getting a pws_fault 392 code when i tried to code a e71

Clear out the contents of your .man file. and save it with nothing in it...Then you shouldnt have a problem....I ran into the same issue coding a e86

[Jay0101]

Originally Posted by jesdan14

mine keeps saying vin faulty why?

I am also having the same error and lists the file A_E65CAS.ipo in the folder sgdat
- INPA works fine

tried intalling new daten files but no change
are there any settings which need to changed? or change the ,.ipo files for a 2007 e92?

[lamia2super]

Originally Posted by vtnard

Clear out the contents of your .man file. and save it with nothing in it...Then you shouldnt have a problem....I ran into the same issue coding a e86

alright ill try it out

[jesdan14]

Thank you it worked, do you know how to do the mirrors fold in when you hit lock and fold out when u hit unlock?
I also have a friend with a 5 series 08 that has the dvd player any way to code to get it to play while driving?
Last question is there a place to see all the coding that I can do and how to do it?

Originally Posted by 1QuikWS6

After you run a Consistency Check, you need to create a profile that you use from then on to write to the car called a .man file

In NCSExpert:

• File > Load profile > Expertmode > OK
• File > edit profile (Password is 'repxet')
• Select 'car-keymemory' (check all 3 boxes) > OK
• Select 'Consistency Check' (should say 'OK') > OK
• Select 'FSW/PSW' ('CVT' selected + both bottom check boxes) > OK
• Select 'Consistency Check' (should say 'OK') > OK

Then create the .man file:

• File > save profile as > (Enter 'Filename' CSEXPER\PFL\xxxx.PFL) > OK

xxxx = 4 digit name of your choosing, not same as what is currently in file name

• File > edit profile (Password is 'repxet') > profile info > set profile name = 'FSW PSW MAN'

You need to load this profile from now on EVERY time you enter NCSExpert to code


After that is done, to code:

Start NCSExpert

• File > > load profile > 'FSW PSW MAN' (will load what you just created above)
• F1 > F3 > E89 > select 'CAS'
• F6 (or back)
• F4 (Process ECU)> select module you want to code, for Windows Up it will be 'CAS' > OK > 'Read ECU'

This will create a FSW_PSW.TRC file for ONLY the module you selected

Close the screen that comes up with all the chinese writing

• Go to Work Folder
• Open FSW_PSW.TRC file with Notepad
• File > save as all > 'FSW_PSW.MAN'

The FSW PSW MAN profile that you just created earlier will use this FSW_PSW.MAN file & this is where you will make your changes

• Open file FSW_PSW.MAN (you should see all the code lines for the module)
• Find 'KOMFORTSCHLIESSUNG_FB' (for windows up thru key fob) -or- 'KOMFORTSCHLIESSUNG_PA' (for windows up thru comfort access) > change to 'aktiv'
• File > save
• Go back to NCS and select F5
• Select 'coapiReadSgGETFSWPSW' > OK (reads all the values including the one you just changed)
• At next screen > OK (should then say 'basic function perfect ended') > OK
• Select F2 (job)
• Select 'SG_CODIEREN > OK
• Select F3 (to execute job)

screen will gray out then you should see 'coding ended' message. Test windows to see if they work

[matrix76]

Originally Posted by jesdan14

Last question is there a place to see all the coding that I can do and how to do it?

https://spreadsheets.google.com/ccc?...CM_xgcAF#gid=0

[jesdan14]

thank you

[1QuikWS6]

do you know how to do the mirrors fold in when you hit lock and fold out when u hit unlock

Either:

SPIEGEL_KOMFORT_EINKLAPP in the FRM (NFRM) Module for 07 to 09'

-or-

ASP_KOMFORT_EINKLAPP in the FRM (NFRM) Module for 10-11'

[jesdan14]

for a 5 series is there a diff spread sheet?
and 1 series

[BlaSTiWi]

Chk post #2020

Originally Posted by jesdan14

for a 5 series is there a diff spread sheet?
and 1 series

[Kalud]

Originally Posted by BlaSTiWi

Chk post #2020

This is just crazy! Imagine someone who just came across this thread... 115 pages and 2530 post! At least there is a search thread function!

[xxxjecxxx]

Never thought this would lead to so many views and replies or a whole new coding section in the forums.

Worked out great

[Nicomons]

Does anyone try to find new code ? The excel sheet stay unchanged since many days.

[orangedawg]

Can anyone who has sirius take a look at their settings and see what they are and in what module (I think it will be in CAS, but not sure). I added $655 to VO to add sirius and it's still not working. I searched and found these values in my car after adding $655 to VO in FRM, Kombi, and CAS.

SDARS
Aktiv
ISPEECH_SDARS
Aktiv
SDARS_PHONE_NUMBER_1
wert_0
RADIO_SDARS
Aktiv
SDARS_IN_EXBOX
Exbox
SDARS_REPLAY_AUTOMATIC
nicht_aktiv
SDARS_INBOX
nicht_aktiv
SDARS_DIAGNOSE
Exbox

Are these values correct? Are there other values that need to be modified? It seemed the only thing that changed after I updated VO was that SDARS went from inactive to active, same with radio-sdars. Thanks for any help!

[Kalud]

Originally Posted by orangedawg

Can anyone who has sirius take a look at their settings and see what they are and in what module (I think it will be in CAS, but not sure). I added $655 to VO to add sirius and it's still not working. I searched and found these values in my car after adding $655 to VO in FRM, Kombi, and CAS.

SDARS
Aktiv
ISPEECH_SDARS
Aktiv
SDARS_PHONE_NUMBER_1
wert_0
RADIO_SDARS
Aktiv
SDARS_IN_EXBOX
Exbox
SDARS_REPLAY_AUTOMATIC
nicht_aktiv
SDARS_INBOX
nicht_aktiv
SDARS_DIAGNOSE
Exbox

Are these values correct? Are there other values that need to be modified? It seemed the only thing that changed after I updated VO was that SDARS went from inactive to active, same with radio-sdars. Thanks for any help!

I have Sirius from factory.

Differences:

SDARS_IN_EXBOX
	inbox
SDARS_REPLAY_AUTOMATIC
	aktiv
SDARS_INBOX
	aktiv
SDARS_DIAGNOSE
	inbox

Also:

RADIO_SDARS
	aktiv

Hope this helps...

[orangedawg]

I'll give it a shot! Thanks!

[dlp3719]

Anyone worked on coding keys? I was talking to NiVeDh about this. We may start looking into it. Just wondering if anyone has already gone down this path.

[Dracon]

Originally Posted by dlp3719

Anyone worked on coding keys? I was talking to NiVeDh about this. We may start looking into it. Just wondering if anyone has already gone down this path.

Define "coding keys"