[lowrydr310]

Originally Posted by Wolf 335

This weekend I tackled the headlights and fog lights restoration.
I did this once last year spring however headlights did get a slight hint of yellowing that bothered me.

Originally done with Cerakote Headlight Restoration Kit.
I contacted them and explained the slight yellowing, and without any hesitation they send out another kit. They definitely stand true to their warranty.

I did the Cerakote kit around the same time last year, and right now it looks just like yours. Not bad, but a hint of yellow which really stands I out in a space gray metallic car. How was their warranty replacement? I only have the digital receipt from where I bought it, the box and empty packages were thrown away long ago.

[tcphoto]

I used the Cerakote kit and they didn't look good after six months or so and they sent a new kit. About a month ago, I decided to use the DA polisher with compound, polish and the Cerakote Ceramic Coating that I used on the new paint. The headlights look great and I did wait a day or so to drive, you cannot control those wild bugs or the weather.

[Hoody007]

Headlights in! Well worth it. Light output is also much better.
Installed the reinforcement brackets too, repaired the bumper as best as I could - but it will get a new cover, fender well pieces, and underbody tray at some point. No rush though, everything is nice and tight.

Cleaned up the engine bay too - Simple Green works very well on coolant.

[Wolf 335]

Originally Posted by lowrydr310

I did the Cerakote kit around the same time last year, and right now it looks just like yours. Not bad, but a hint of yellow which really stands I out in a space gray metallic car. How was their warranty replacement? I only have the digital receipt from where I bought it, the box and empty packages were thrown away long ago.

That should be suffient enough. If you bought through Amazon, you can contact them directly through their seller page.

Originally Posted by tcphoto

I used the Cerakote kit and they didn't look good after six months or so and they sent a new kit. About a month ago, I decided to use the DA polisher with compound, polish and the Cerakote Ceramic Coating that I used on the new paint. The headlights look great and I did wait a day or so to drive, you cannot control those wild bugs or the weather.

I was under the impression tha the surface should be a bit rough (3000 grit) so coating can adhere properly. I guess headlight ceramic coating is different from paint coating? If i have to re-do this again next year, i'll try your method.

[BRG_N54]

Not my car, but found out why my friends 330 was getting misfires in cylinders #3 & #6. One half of the DISA flap was in #3 and the other half was in #6!! Also found the shaft rattling around in the manifold. What a horrible design! fortunately, nothing was ingested, but the plastic was eroded away from bouncing around in there, runs a lot better now too!

[3PedalJake]

Today got my headliner, package tray and sunroof installed. Did the wiring for my leather power seat retrofit, happily my car had all the power wires to run the base even though the original seats are manual vinyl sport seats. They had power bolster though, so I knew that wire would be there. The only thing I had to add was the canbus wire to keep the seats alive and for the memory function. I tapped into the canbus just forward of the left side subwoofer and spliced a piece of cable in with heat shrink solder connectors. I managed to draw the cable through the wire shield for the part that is visible in the car so it all looks factory fresh, pinned it up and re-taped. Now hopefully I'll plug in the seats and they'll just work (yeah good luck w/ that lol).

[spazzz]

Originally Posted by Wolf 335

This weekend I tackled the headlights and fog lights restoration.
I did this once last year spring however headlights did get a slight hint of yellowing that bothered me.

Originally done with Cerakote Headlight Restoration Kit.
I contacted them and explained the slight yellowing, and without any hesitation they send out another kit. They definitely stand true to their warranty.

Cerakote kit doesn't require the use of any tools, so it is all elbow grease when it comes to sanding, and I think this is where the fault lies. This time around I purchased a drill sanding kit from amazon and went to town.

There was some stone pitting so I decided to start with 800 grit > 1000 > 2000 > 3000.
This was all done with a drill and then I did another round of 3000 grit hand sanding as per Cerakote instructions "in straight back and forth motion, not circular".

After that applied the ceramic coating and lights looked beautiful.

BEFORE (yellowed and dirty):

Attachment 3570634 Attachment 3570635

Obligatory sanding pic:

Attachment 3570636

AFTER:

Attachment 3570638 Attachment 3570639

Attachment 3570640 Attachment 3570641

It's not over, things get worse!

As per their instructions it says to wait a minimum of 60 minutes before driving and 24h before exposing to water.
I waited approximately close to 2 hours before needing to drive for about 20 minutes. No rain, no water, clear nice day.

I park and go to look and admire the lights and what do I see on the passenger lens...a huge bug guts splattered dead center.

- Didn't want that fully curing into the ceramic coating and I made a mistake trying to wipe it off. Needless to say that turned to a smearing disaster. Coating still had some tackiness to it so you can imagine the disaster scene.
- I then took some 99% alcohol and just wiped the whole headlight ultimately compromising the entire coating.

Attachment 3570653 Attachment 3570660

Contacted Cerakote this morning explaining what happened and that I was wondering if i could just buy the ceramic coating instead of the whole kit. They are sending me ceramic coating for free asap. Needless to say, amazing customer service.

So, i will be redoing my passenger headlight.
To be safe, this time around not going to drive the car for at least 24h after coating.

Next time give a XPEL precut kit a whirl. These lights still look like day one.
My daughters '08, E92 was easy to do for a first timer.

[Onizukachan]

Yesterday drivers side ac was feeling warm.

Went and got two OG analog ac thermometers, one for each side and topped up the charge by adding r134a for a second or two, then waiting a minute or two for it to stabilize and show the change. Eventually got it down to an indicated 43-44 degrees per side.

[oVeRdOsE.]

600km trip, done and car still alive !

[lowrydr310]

Originally Posted by oVeRdOsE.

600km trip, done and car still alive !

What angel eye rings are those? They look good. I'm doing lens and projector replacement soon on my 330 (currently has LCI lights) and I'm thinking of replacing the halos. I'd like to keep the round ones and avoid the F series flat bottom ones.

Yeah nevermind the e91 with a N54, I'm focused on the headlights.

[oVeRdOsE.]

Originally Posted by lowrydr310

What angel eye rings are those? They look good. I'm doing lens and projector replacement soon on my 330 (currently has LCI lights) and I'm thinking of replacing the halos. I'd like to keep the round ones and avoid the F series flat bottom ones.

Yeah nevermind the e91 with a N54, I'm focused on the headlights.

great question, I dont know ! Came with the car.

So from what I can tell :

- headlights are OEM
- Angel eyes got white and amber color
- When I plug this LCI headlight on my pre-lci car, the amber angel was flashing with the flashers when the night lights were on.
- Now back on an LCI car, no amber at all at any moment.
- angel eye are mounted on a 3D printed bracket
- there's some resistor and wiring involved.

so, in conclusion, seems to be a kit from a small seller.

[bimmermech123]

Originally Posted by lowrydr310

What angel eye rings are those? They look good. I'm doing lens and projector replacement soon on my 330 (currently has LCI lights) and I'm thinking of replacing the halos. I'd like to keep the round ones and avoid the F series flat bottom ones.

Yeah nevermind the e91 with a N54, I'm focused on the headlights.

DIY please on the projector replacement

[Wolf 335]

Originally Posted by Efthreeoh

Grounds are 18. Others are 22.

Isn't green/yellow wire standard for ground wire?

[StradaRedlands]

Installed some of MidWillamette335d's strut tower covers last night... they are so cool! (disregard the dust... the camera adds 20 lbs)

[StradaRedlands]

Originally Posted by oVeRdOsE.

600km trip, done and car still alive !

E91 love!!!

[Hoody007]

Originally Posted by spazzz

Next time give a XPEL precut kit a whirl. These lights still look like day one.
My daughters '08, E92 was easy to do for a first timer.

Interesting - looks like they have it for the pre-LCI E90s, just not the LCIs. As it’s a whole set with the fog lights included I figure that’s why. Is it pretty straightforward to apply?

[spazzz]

Well, I did sand progressively 600, 800, 1000, 1500, 2000, 3000 with a drill then used Megs 100 and a wool tufbuff on a Flex3401 followed by Essence and a Lake Country white Force pad.
Then mixed the slip and grab solutions in a couple Kwazar sprayers and got to work.
I watched a few videos before hand.

[RealJ22]

I am now the proud owner of a e90 again. This is my 3rd e9x chassis and I still have the coupe. It’s a 2011 salvage title with 125k on it. It has a few odds and ends, but cleaned up nicely. I paid $800 and drove it 50 miles home.


best image hosting websites

[StradaRedlands]

Originally Posted by RealJ22

I am now the proud owner of a e90 again. This is my 3rd e9x chassis and I still have the coupe. It’s a 2011 salvage title with 125k on it. It has a few odds and ends, but cleaned up nicely. I paid $800 and drove it 50 miles home.


best image hosting websites

Wow, that's great! Did you get from Copart or county auction, or ???

[RealJ22]

Originally Posted by StradaRedlands

Wow, that's great! Did you get from Copart or county auction, or ???

A younger guy bought it and I think he may have been overwhelmed. Someone did the repairs earlier. Drivers airbag and pass side curtain were blown. Luckily I had a spare sport wheel with an airbag I thew right on.

The FRM needs a reset or I may possibly have to replace it. Two people can help me locally if necessary. I have gone through some of the codes and have a few options.

I’ve only been able tinker with it for a few hours, but will probably document everything.

[StradaRedlands]

Originally Posted by RealJ22

A younger guy bought it and I think he may have been overwhelmed. Someone did the repairs earlier. Drivers airbag and pass side curtain were blown. Luckily I had a spare sport wheel with an airbag I thew right on.

The FRM needs a reset or I may possibly have to replace it. Two people can help me locally if necessary. I have gone through some of the codes and have a few options.

I’ve only been able tinker with it for a few hours, but will probably document everything.

Very cool, it will be a great project!

[RealJ22]

The old wheel was absolutely disgusting