[Brule]

Thats what Im going to do for the pipe.
1800au i paid for the intercooler

the silicone chargepipes look the part.

I only made my charge pipe to increase the flow a bit for $100.
I plan on getting RB evos as soon as they are ready.

[Brule]

Update of installing stealths and AD intercooler.

Hot charge pipe with squash gone fits well.

Had to take the front bar off for the first time.

Had to cut a heap of plastic to fit the intercooler.

Intercooler fit well in oem position.
Andy sent silicone for both sides.
The hotside fits like oem.

Other side has a small gap so i will have to take the charge pipe out and fabricate a small angle on the end of it to fit down to the intercooler. Image attached.

Front bar back on

Started fitting catch can, inlets together with diverter valves.

Had a good bit of work completed today.

Tomorrow I'll start the new precat o2 sensors and downpipes

[Brule]

Down pipes and new O2 sensors are in.

[Brule]

Bought a 3inch 90 degree bend from bursons with beads on each end.

Started cutting the pipe to make it much tighter to extend my cpe chargepipe.

I'll get it made tomorrow.

Then I need to put my coolant tank and vacuum lines and intake engine cover.

[Brule]

Chargepipe is currently being welded to my custom bend.

Should have it back tonight to fit!

Still have stock exhaust that I do not want to put back on.

I will put it on but will try and get rid of that flap asap, cause it rattles.

[EB89]

Originally Posted by Brule

Chargepipe is currently being welded to my custom bend.

Should have it back tonight to fit!

Still have stock exhaust that I do not want to put back on.

I will put it on but will try and get rid of that flap asap, cause it rattles.

Cut it off?

[Brule]

I have only had the exhaust off once, I havnt really had a look at it yet.

Its currently in but nit connected to the dps.

I want to cut the cat and the perforated pipe in the muffler out and replace it with straight pipe, and cut the flap out some how.

Just don't have the patience to do it at the moment, I want to have a go with the new turbos asap.

[Socket]

When it this gonna be done Brule Cant wait to see how she goes

[Brule]

Was hoping last night but didn't get my pipe back.

[CashedUpBogan]

Nekkminit, EVOs are ready. Repeat entire process in a couple of months haha

[Brule]

I dare say rob will make something like vtts new offering.

I was planning on getting evos asap but looks like vtt has a bit if an edge on them with a new manifold design.

[Brule]

Went to pick the chargepipe up but it wasn't cleaned up inside. So ill pick it up tomorrow arvo.

[Brule]

Installed chargepipe it fits well so I put all the intake side on complete.

Started I stalling vacume lines to actuators.

When I got under I noticed the reat oil drain at the top is leaking.

I already took that drain off as it was leaking, the flange was not straight so I bent it flat and reinstalled it Last wknd.


I'm super pissed right now.

I was getting ready to put my new stealth tune on tonight!

[Brule]

Went ahead and put all vaccum lines and coolant tank on.

Filled coolant and have a leak at the top coolant line to block.

[iliketurtl3s]

That the one with the plastic butterfly looking connector?

[Brule]

Maybe? The front turbo top coolant line.

Fixed it, it had no O ring . Oops.

Nipped rear oil drain a bit, I will prime turbos and if it leaks I will pull dps and sought it out

[Brule]

Primed turbos last night. No visible leak initially.
This morning there was oil line coming down the drain pipe.

Coolant top line now has an o ring fitted, I havnt topped it up but all vacuum lines are back on and expansion tank is installed, again.

Now I'm back at removing o2 sensors and dps to get the rear oil drain off again

[CashedUpBogan]

Are you planning on running PI? Just seen the EVOs with PI run back to back 10.8s. Be keen to see what these can do here

[Brule]

The guy that just ran 10.8s has got rb stealths not evos.

He did 10.9 with classic rbs.


A south Africa guy with rb stealths made 600hp on pump +meth.

I will only be around 500-530 with my basic setup.
I also have a manual so realistically looking like 11.5 second area

[CashedUpBogan]

He's running Super RBs, which are EVOs, not Stealths, right?

http://www.e90post.com/forums/showthread.php?t=1228155

[Brule]

His previous threads show stealths.

Check out his thread that started before Christmas. On terrys site

Google rb stealths. He's first with images of stealths when he got them
On you tube, you can see he has tft inlets so they cant be evos.

Evos are more efficient than stealth with large hot chargepipe and shortened intake that stays on left side of engine bay into an
air filter.

The stealth and evo have the same wheel combination but stealths would lack the top end of the evos upgraded intake and chargepipe

[Brule]

Just installed the oem oil drain lets hope it seals.