[wursti]

No. Mine just auto pops and the follow me home works. But: My follow me home function stays on just for a second. if I press again, it stays again just for a sec. After pressing a third time, it stays on for longe. Dunno why... any ideas?

[erickarlborg]

Originally Posted by wursti

No. Mine just auto pops and the follow me home works. But: My follow me home function stays on just for a second. if I press again, it stays again just for a sec. After pressing a third time, it stays on for longe. Dunno why... any ideas?

Sounds like you have the HEIMLEUCHTEN_ABBRUCH activated

[wursti]

Yep. Thank you!

[erickarlborg]

Originally Posted by wursti

Yep. Thank you!

No problem! Tried activating this on a friends car thinking it would enable to cut off the lights by pressing the button again... That was not the case

Also an update on my car, it does indeed release the hatch on long press. So it has been working like it should this whole time

[kckirch]

Originally Posted by Sensible_

It works fine on my FRM2. And everyone else's I've done it on. Are you holding the button down properly?

Just need some help running frm1. Following that written guide. But after replacing those 2 lines with the new 3 lines NCS expert won’t let that FRM file read or write anything basically because somewhere in that line is incorrect.

Could you take a look at my file. I can show you a comparison with the new line added and see if anything is wrong. The errors are on the new outputted file

[Yngvejos]

Originally Posted by kckirch

Just need some help running frm1. Following that written guide. But after replacing those 2 lines with the new 3 lines NCS expert won’t let that FRM file read or write anything basically because somewhere in that line is incorrect.

Could you take a look at my file. I can show you a comparison with the new line added and see if anything is wrong. The errors are on the new outputted file

I just did this on my FRM1 (05 E91 touring).
If your FRM have codingindex 12, you can use the attached modified daten file.

Just remove the PDF extension and replace FRMFA.C12 file in NCS expert.

[kckirch]

Originally Posted by Yngvejos

I just did this on my FRM1 (05 E91 touring).
If your FRM have codingindex 12, you can use the attached modified daten file.

Just remove the PDF extension and replace FRMFA.C12 file in NCS expert.

My car has FRMFA.C11
Can I update my frm to get on 12?

[kckirch]

Originally Posted by Yngvejos

I just did this on my FRM1 (05 E91 touring).
If your FRM have codingindex 12, you can use the attached modified daten file.

Just remove the PDF extension and replace FRMFA.C12 file in NCS expert.

Update I got it to work on mine. Just need to do the DRL now! If anyone knows the proper address for it let me know.

Going to make an in depth youtube video to show how to do this coding

[rico_g01]

How can i add Welcome lights to frm1, it does not show up in FRMFA.C12

[Sensible_]

Originally Posted by rico_g01

How can i add Welcome lights to frm1, it does not show up in FRMFA.C12

Seriously? This guy just did it for you...

Look 2 posts up...

https://www.bimmerpost.com/forums/sh...php?p=24973636

[rico_g01]

That file has only follow me home, i need to activate welcome lights

[iFURY]

Originally Posted by kckirch

Just need some help running frm1. Following that written guide. But after replacing those 2 lines with the new 3 lines NCS expert won’t let that FRM file read or write anything basically because somewhere in that line is incorrect.

Could you take a look at my file. I can show you a comparison with the new line added and see if anything is wrong. The errors are on the new outputted file

I have the same problem, can u explain how u fix that?

[RaZVaN_17]

Hi! So I tried all of the above steps and no success. Maybe you guys can't help me out.
First of all, my car is a BMW Z4 E89 (2013) with NFRM3.
The car has comfort access also.

I already had all the codings for Follow me home done on the car (all HEIMLEUCHTEN, including HEIMLEUCHTEN_FUNKSCHL)

In the CAS module I set SONDERTASTE_PANIKALARM to panikalarm.

I use NCSexpert and NCSdummy. They are working correctly and I know how to code with them.

If I press the remote button 3 (trunk) shortly the car doesn't do nothing.
If I press 0.5s the trunk opens
If I keep the button pressed for 2second nothing happens.

Any ideas or help is very much appreciated!
Thank you.

[Tunafish]

You should have the option in Idrive on the FRM3 with no coding needed.. On page 86 of your owners manual set the pathway timer to how long you want the follow me home light to be active.. They will auto turn off so no need to push a button.

[RaZVaN_17]

Originally Posted by Tunafish

You should have the option in Idrive on the FRM3 with no coding needed.. On page 86 of your owners manual set the pathway timer to how long you want the follow me home light to be active.. They will auto turn off so no need to push a button.

I have the menu option and I also set it up for 30sec. The Follow me home function works if I use the headlamp flasher switch.
I am trying to turn the follow me home function by pressing the remote 3'rd button (trunk).

Thanks for the support.

[Tunafish]

Or you can use the unlock button and use the welcome lights if you want to use the remote.. Not sure why you want to use the trunk button?

[megaspeed]

I've managed this part was pretty straight forward, then I went to look in to welcome lights

block for welcome lights in FRM3_E89.C32 is used for DRL in FRMFA.C12 which is the daten file mine uses to code in NCS expert, I am wondering if I could replace DRL with WL in this block, I can live without DRL, I can turn on the angel eyes myself