[chilledn52]

Originally Posted by Dru128m

Where does the MAP sensor go? I couldn't get any vacuum to read porting into a runner, maybe if I would have used all six it would have been enough.

Also n52 has vacuum pump cause from factory it never made enough vacuum in the manifold

[chilledn52]

My own 3D printed velocity pipe bumper intake for the velocity stacks, sold a few already

[jonwilli]

Is there any news on the final production velocity stacks? I thought they were meant to be available for sale a couple of months ago?

[chilledn52]

Originally Posted by jonwilli

Is there any news on the final production velocity stacks? I thought they were meant to be available for sale a couple of months ago?

Best I can say is that the tuning is taking longer then expected. Don’t think anyone is at a final tune yet as the problems are timing, smooth throttle response, better fuel economy

[chilledn52]

Never shared the dyno run I’ve done -

[chilledn52]

Beta tune not fully complete
Hitting a torque limiter
Low timing 7 degrees off
Not most power of out tune
83F or 30C outside air temp
2200ft -6% off

234rwhp / 194ftlb - mustang dyno
254rwhp / 207ftlb - dyno jet conversion

[jonwilli]

I'm guessing tuning for velocity stacks and cams could be a nightmare then when they are released? Any idea if this is on 22RPDs future plans?

[The Nightman]

Originally Posted by chilledn52

Beta tune not fully complete
Hitting a torque limiter
Low timing 7 degrees off
Not most power of out tune
83F or 30C outside air temp
2200ft -6% off

234rwhp / 194ftlb - mustang dyno
254rwhp / 207ftlb - dyno jet conversion

Thanks for the update. Impressive so far and sounds glorious

[chilledn52]

Originally Posted by jonwilli

I'm guessing tuning for velocity stacks and cams could be a nightmare then when they are released? Any idea if this is on 22RPDs future plans?

I’m not sure, if 22RPD gets solid velocity stacks tune, and these cams still use valvetronic then I assume it can be done

[chilledn52]

We have replaced the exhaust camshaft ledge due to scoring from being on track with less then FULL oil on digital dipstick. We had reduced timing, some exhaust scoring.

At the same time we installed MILVs from CobraMarty for increased lift

And cleaned up the valve cover to redo my crinkle black valve cover.

We are back on the roads with healthy engine, for more beta testing more.

[colorado.e9x]

Good to hear. Any butt meter difference with MILVs?

[chilledn52]

Originally Posted by colorado.e9x

Good to hear. Any butt meter difference with MILVs?

butt meter has seen in increase of power and torque at almost every point in rev range

[jonwilli]

Originally Posted by chilledn52

butt meter has seen in increase of power and torque at almost every point in rev range

What are you thoughts on this video?

I think you were in contact with Bruno when he was testing? I have MILVs fitted at the moment but hope to move to upgraded cams from StageFP or BDS once they have been released/tested a bit more.

[chilledn52]

Originally Posted by jonwilli

What are you thoughts on this video?

https://www.youtube.com/watch?v=u4zKBsJRvYA

I think you were in contact with Bruno when he was testing? I have MILVs fitted at the moment but hope to move to upgraded cams from StageFP or BDS once they have been released/tested a bit more.

Contact with Bruno? No
To my understanding, technically it’s just changing the position of the eccentric shaft so at a given rpm point, you have more valve lift.

[chilledn52]

Originally Posted by colorado.e9x

Good to hear. Any butt meter difference with MILVs?

MILVs on N54 manifold is WAY more noticeable then it was for me on velocity stacks.
On N54 manifold at this point cause not more much tuning needed, pretty much done on mine.
I still have 2A87 exhaust mechanism so I do have to tear back into the car.

If you plan on getting these velocity stacks, good healthy engine is required for sure.

[colorado.e9x]

Thanks for the info! Whats your thoughts on it so far compared to the N54 manifold?

[chilledn52]

Originally Posted by colorado.e9x

Thanks for the info! What's your thoughts on it so far compared to the N54 manifold?

gonna have to get readjusted to the n54 manifold with milvs now. trumpets are drone-y and higher fuel economy, doing lots of highway.

[AmuroRay]

Originally Posted by chilledn52

gonna have to get readjusted to the n54 manifold with milvs now. trumpets are drone-y and higher fuel economy, doing lots of highway.

Economy or consumption? Did you run a filter? And plan for them to put a pendulum on the trumpets?

[chilledn52]

Originally Posted by AmuroRay

Economy or consumption? Did you run a filter? And plan for them to put a pendulum on the trumpets?

consumption. some beta users have same fuel economy while mine has increased at least by +4-5L/100km at highway speeds.
3.91 diffs and over 3k isnt helping.
running a K&N prefilter over the trumpets