Another Procede Log Help Thread

pits200 · 04-15-2012, 12:16 PM

Here is another one showing afrs with better scaling..

enrita · 04-15-2012, 12:24 PM

you should really focus on logging 1 gear only at a time and make it bigger.... timings looks like crap.

Ilma · 04-15-2012, 12:41 PM

Quote:

Originally Posted by pits200

Here is another one showing afrs with better scaling..

Hard to read as Enrita states.....but it looks like you are hitting 12:1 AF up top.
Seems Ok then.

Like Myst mentioned = flatlining timing there is no fix.

I will be looking at my injectors pretty soon.

scottro · 04-15-2012, 03:47 PM

See my thread here: http://www.e90post.com/forums/showthread.php?t=673636

I was just recently able to fix my flatline timing by lowering boost. Perhaps you are running too much boost for your conditions. I also learned that inlet air temperature can play a large role in my timing curve. With a delta in intake air temperature of just 10degF (90 degF vs 100degF), I can see a big difference on logs.

OpenFlash · 04-15-2012, 03:57 PM

OP-- PM'd you

Ilma · 04-16-2012, 07:04 PM

Quote:

Originally Posted by themyst

Rob@Cobb had a theory that Fuel Mode 6 was causing flatlining behavior, but it wasn't the case.

Well we seem to be running out of theories

Did you figure out why your plug on cylinder 6 was so fouled?

Perhaps that could have been an injector running rich issue

themyst · 04-16-2012, 07:30 PM

Quote:

Originally Posted by Ilma

Well we seem to be running out of theories

Did you figure out why your plug on cylinder 6 was so fouled?

Perhaps that could have been an injector running rich issue

General consensus is a bad valve cover gasket. I doubt it's my injector but I may swap it anyway since they're cheap now.

30 bucks for the gasket, 120 for an injector, sound right?

Ilma · 04-16-2012, 10:06 PM

Quote:

Originally Posted by themyst

General consensus is a bad valve cover gasket. I doubt it's my injector but I may swap it anyway since they're cheap now.

30 bucks for the gasket, 120 for an injector, sound right?

If it was the valve cover gasket I imagine there would have been some oil pooling at the top of the spark plug and then working it's way down the threads into the combustion chamber area....no

On another note to dispel this theory, I reloaded the latest firmware and default stage 2 map which is running 87% open loop fueling straight from the factory settings and pulled about 3 logs - all with stellar timing post shift.

1 psi higher than what I was running before and getting post-shift drops with.

It was also about 15 degrees warmer ambients tonight too.

So much for the too much boost and heat theory

This is a real stumper

.
.
.
.

Dark9T · 04-17-2012, 12:23 AM

sorry... to hijack your thread becuz dont wanna open other one.
please tell me this those logs are normal or no..

3-17 agg beta map
stg2

Uploaded with ImageShack.us

stg2

Uploaded with ImageShack.us

stg3

Uploaded with ImageShack.us

themyst · 04-17-2012, 09:43 AM

Quote:

Originally Posted by Dark9T

sorry... to hijack your thread becuz dont wanna open other one.
please tell me this those logs are normal or no..

3-17 agg beta map
stg2

Uploaded with ImageShack.us

stg2

Uploaded with ImageShack.us

stg3

Uploaded with ImageShack.us

If that's on pump gas only, doesn't look all that bad. You're close to tapped on your fuel trims though. You might want to add a bit more ignition correction as well because you keep dropping timing in the next gear. Can't really say if that timing drop means anything or not because it's only cylinder 1 feedback.

Dark9T · 04-17-2012, 01:10 PM

91octane, my AFR is Running super rich.. But I can't show that log some how..

Dark9T · 04-17-2012, 01:13 PM

more ignition correction ? Right now I am at 100.392, how many % u think is good for me?

Kalud · 04-17-2012, 01:36 PM

Quote:

Originally Posted by Dark9T

more ignition correction ? Right now I am at 100.392, how many % u think is good for me?

Just a long shot here, but have you tried resetting adaptations ? Doesn't take much time to try and it might actually help.

Dark9T · 04-17-2012, 01:42 PM

i see my AFR lower down to 9.85!!!!!!! i hope i am wrong here...
stg2 AFR

Uploaded with ImageShack.us

stg3 AFR

Uploaded with ImageShack.us

Dark9T · 04-17-2012, 01:45 PM

Quote:

Originally Posted by Kalud

Just a long shot here, but have you tried resetting adaptations ? Doesn't take much time to try and it might actually help.

i can reset it again, only takes like a 1min or 2

themyst · 04-17-2012, 01:55 PM

Quote:

Originally Posted by Dark9T

more ignition correction ? Right now I am at 100.392, how many % u think is good for me?

I believe Ignition Correction is on a 0-200% scale? That's from the Procede V4 days though so I could be wrong on that. If there is a 0-200% scale, you may want to increase IC to 125%. 91 octane is crap.

OpenFlash · 04-17-2012, 02:01 PM

Quote:

Originally Posted by Dark9T

i see my AFR lower down to 9.85!!!!!!! i hope i am wrong here...
stg2 AFR

Uploaded with ImageShack.us

stg3 AFR

Uploaded with ImageShack.us

You are not viewing AFR correctly because your scaling is off. Don't be concerned with AFR during the shift event. It's going to read very rich but it's only for a fraction of a second.

And I suggest leaving your ignition correction alone. If you are running pump gas, it's not unexpected to see a knock retard event towards the top of 4th gear. You can certainly increase ignition correction or lower boost to get rid of it but you will effectively be making your car slower. Either way, the car is running safely and strongly. Sometimes it's a good idea to leave things alone

Shiv

Kalud · 04-17-2012, 02:17 PM

Quote:

Originally Posted by Dark9T

i see my AFR lower down to 9.85!!!!!!! i hope i am wrong here...

You have your scaling wrong, Press "P" in the AFR window to change the scaling for something like 10 to 20 and remove the "AutoScale".

Dark9T · 04-17-2012, 02:34 PM

Quote:

Originally Posted by Kalud

You have your scaling wrong, Press "P" in the AFR window to change the scaling for something like 10 to 20 and remove the "AutoScale".

THANK YOU SO MUCH!!

Dark9T · 04-17-2012, 02:34 PM

Quote:

Originally Posted by shiv@vishnu

You are not viewing AFR correctly because your scaling is off. Don't be concerned with AFR during the shift event. It's going to read very rich but it's only for a fraction of a second.

And I suggest leaving your ignition correction alone. If you are running pump gas, it's not unexpected to see a knock retard event towards the top of 4th gear. You can certainly increase ignition correction or lower boost to get rid of it but you will effectively be making your car slower. Either way, the car is running safely and strongly. Sometimes it's a good idea to leave things alone

Shiv

Yes sir!!

Dark9T · 04-17-2012, 02:36 PM

stg3 there

Uploaded with ImageShack.us

Kalud · 04-17-2012, 02:39 PM

Las Vegas heat + 91 octane, you wouldn't believe what meth would do to your car

04-15-2012, 12:16 PM	#23
pits200 Colonel 552 Rep 2,598 Posts Drives: 09 335i X-Drive Black Sapphire Join Date: Mar 2010 Location: Pittsburgh iTrader: (1)	Here is another one showing afrs with better scaling..
	Appreciate 0 Quote

04-15-2012, 12:24 PM	#24
enrita Major General 161 Rep 7,377 Posts Drives: 335i - Big turbos Join Date: Sep 2008 Location: Italian in Sweden iTrader: (0)	you should really focus on logging 1 gear only at a time and make it bigger.... timings looks like crap. __________________ 07 335i AT - MOTIV 750 - MHD E85 BMS flash - BMS PI - JB4G5 - Okada Coils - NGK 5992 Plugs - Helix IC - Snow Stg. 3 - Stett CP - Custom midpipes with 100 HJS Cats - Bastuck Quad - PSS10 - QUAIFE LSD - BMS OCC - Forge DVs - AR OC - ALCON BBK - M3 Chassi - Dinan CP - Velocity M rear Toe arms - Advan RZ-DF - LUX H8 - Level 10 AT upgrade
	Appreciate 0 Quote

04-15-2012, 03:47 PM	#26
scottro Second Lieutenant 19 Rep 205 Posts Drives: E70 X5M Join Date: Sep 2011 Location: Phoenix, AZ iTrader: (0)	See my thread here: http://www.e90post.com/forums/showthread.php?t=673636 I was just recently able to fix my flatline timing by lowering boost. Perhaps you are running too much boost for your conditions. I also learned that inlet air temperature can play a large role in my timing curve. With a delta in intake air temperature of just 10degF (90 degF vs 100degF), I can see a big difference on logs.
	Appreciate 0 Quote

04-15-2012, 03:57 PM	#27
OpenFlash 1809 Rep 17,960 Posts Drives: A Lot Join Date: Sep 2006 Location: SF Bay, CA iTrader: (0) Garage List 2018 Ducati Panigal ... [0.00] 2016 Mazda CX5 [0.00] 2017 Aprilia Tuono ... [0.00] 2019 BMW M2 Competi ... [0.00] 2015 BMW M5 Competi ... [10.00] 2016 Ducati XDiavel S [0.00] 2016 AMG GT S [0.00] 2011 Ferrari 458 It ... [0.00] 2017 Charger Hellcat [0.00] 2015 KTM Super Duke ... [0.00] 2016 KTM RC390 [0.00]	OP-- PM'd you
	Appreciate 0 Quote

04-17-2012, 12:23 AM	#31
Dark9T Captain 26 Rep 660 Posts Drives: 2010 Red 335i E92 AT Join Date: Jun 2011 Location: las vegas iTrader: (0)	other procede rev3 log need help sorry... to hijack your thread becuz dont wanna open other one. please tell me this those logs are normal or no.. 3-17 agg beta map stg2 Uploaded with ImageShack.us stg2 Uploaded with ImageShack.us stg3 Uploaded with ImageShack.us stg3 Uploaded with ImageShack.us __________________ PROcede REV3+OpenFlash "Custom DynoTune" //Vishnu PWM Meth kit//AIS Meth Tank//18" Forgestar F14//BridgeStone RE11//WaveTrac LSD n M3 Bushing// KW V3 Coilovers//ETS 6.25" FMIC//MS Ceramic Coated 3" DPs//aFe DCI//M3 style body kits//HPF GEN2 Exhaust//Performance CF Trunk Lip//FFTEC walbro 450 inline pump kit// Last edited by Dark9T; 04-17-2012 at 03:03 AM..
	Appreciate 0 Quote

04-17-2012, 01:10 PM	#33
Dark9T Captain 26 Rep 660 Posts Drives: 2010 Red 335i E92 AT Join Date: Jun 2011 Location: las vegas iTrader: (0)	91octane, my AFR is Running super rich.. But I can't show that log some how.. __________________ PROcede REV3+OpenFlash "Custom DynoTune" //Vishnu PWM Meth kit//AIS Meth Tank//18" Forgestar F14//BridgeStone RE11//WaveTrac LSD n M3 Bushing// KW V3 Coilovers//ETS 6.25" FMIC//MS Ceramic Coated 3" DPs//aFe DCI//M3 style body kits//HPF GEN2 Exhaust//Performance CF Trunk Lip//FFTEC walbro 450 inline pump kit//
	Appreciate 0 Quote

04-17-2012, 01:13 PM	#34
Dark9T Captain 26 Rep 660 Posts Drives: 2010 Red 335i E92 AT Join Date: Jun 2011 Location: las vegas iTrader: (0)	more ignition correction ? Right now I am at 100.392, how many % u think is good for me? __________________ PROcede REV3+OpenFlash "Custom DynoTune" //Vishnu PWM Meth kit//AIS Meth Tank//18" Forgestar F14//BridgeStone RE11//WaveTrac LSD n M3 Bushing// KW V3 Coilovers//ETS 6.25" FMIC//MS Ceramic Coated 3" DPs//aFe DCI//M3 style body kits//HPF GEN2 Exhaust//Performance CF Trunk Lip//FFTEC walbro 450 inline pump kit// Last edited by Dark9T; 04-17-2012 at 01:29 PM..
	Appreciate 0 Quote

04-17-2012, 01:42 PM	#36
Dark9T Captain 26 Rep 660 Posts Drives: 2010 Red 335i E92 AT Join Date: Jun 2011 Location: las vegas iTrader: (0)	i see my AFR lower down to 9.85!!!!!!! i hope i am wrong here... stg2 AFR Uploaded with ImageShack.us stg3 AFR Uploaded with ImageShack.us __________________ PROcede REV3+OpenFlash "Custom DynoTune" //Vishnu PWM Meth kit//AIS Meth Tank//18" Forgestar F14//BridgeStone RE11//WaveTrac LSD n M3 Bushing// KW V3 Coilovers//ETS 6.25" FMIC//MS Ceramic Coated 3" DPs//aFe DCI//M3 style body kits//HPF GEN2 Exhaust//Performance CF Trunk Lip//FFTEC walbro 450 inline pump kit//
	Appreciate 0 Quote

04-17-2012, 02:36 PM	#43
Dark9T Captain 26 Rep 660 Posts Drives: 2010 Red 335i E92 AT Join Date: Jun 2011 Location: las vegas iTrader: (0)	stg3 there Uploaded with ImageShack.us __________________ PROcede REV3+OpenFlash "Custom DynoTune" //Vishnu PWM Meth kit//AIS Meth Tank//18" Forgestar F14//BridgeStone RE11//WaveTrac LSD n M3 Bushing// KW V3 Coilovers//ETS 6.25" FMIC//MS Ceramic Coated 3" DPs//aFe DCI//M3 style body kits//HPF GEN2 Exhaust//Performance CF Trunk Lip//FFTEC walbro 450 inline pump kit//
	Appreciate 0 Quote

04-17-2012, 02:39 PM	#44
Kalud Lieutenant 29 Rep 582 Posts Drives: e92 335i Join Date: Jun 2010 Location: Canada iTrader: (0)	Las Vegas heat + 91 octane, you wouldn't believe what meth would do to your car
	Appreciate 0 Quote