[bmw 328i]

is their any code to close the windows with the key fob by holding the lock button on the fob.

[Ti317]

Originally Posted by bmw 328i

is their any code to close the windows with the key fob by holding the lock button on the fob.

Yes.
Go to a site like BMWcoders dot com or
BMW coding dot com.
There are step by step tutorials.

You need to type the addresses in with no spaces.

[hotstrick]

hey im trying to install but its asking me for a file named EDIC-DRIVER NOT PART OF THIS SETUP. please help email me at hotstrick@yahoo.com thank you trying to code injectors

[Dan Bilzerian]

Do ncs and inpa work with windows 10 or do I need to have a dual boot?

[blink977]

Originally Posted by Dan Bilzerian

Do ncs and inpa work with windows 10 or do I need to have a dual boot?

newer version of inpa will work, but it is more complicated to install, than in XP or Windows7

[Dan Bilzerian]

Originally Posted by blink977

newer version of inpa will work, but it is more complicated to install, than in XP or Windows7

I'm following this guys explanation, I'm just getting lost a little bit. I've never really done anything like this. I've gotten as far as the Command Line Syntax and that's where I'm lost

[ctuna]

Look at wildcatcrazys posts.

[Flyboy161]

So far I've coded my '11 328i using NCS and Carly. I enabled the digital speedometer, uncorrected and enabled Bluetooth using NCS Expert, and registered the battery and enabled Angel Eyes for DRL using Carly. Carly is great for simple stuff, but INPA and NCS are the way to go for more in depth troubleshooting, IMHO.

Also coded my 2012 335i for the digital speedometer right after buying it.

[ProAktion]

Good read here. I could not find anything that says this program will work with a bluetooth ELM. It only works with a cable correct?

[808AWD325xi]

Originally Posted by ProAktion

Good read here. I could not find anything that says this program will work with a bluetooth ELM. It only works with a cable correct?

BMW Group software does not support ELM327 cables, you need a K+DCAN cable.

[lnxguy]

Anyone know if you can code the car so after you enter and close the door your seat continues to move to its saved position?

Example:

I unlock the car (seat does nothing), I open the door (Seat moves), I close the door(seat stops). If my gf is driving the car before me, she has the seat so far up that by the time I've opened the door and closed it the seat still isn't in 'my' position. Then I get in, start the car and press '1' on the memory seat to finish moving the seat.

Make sense? lol

[Gearhead43]

Very very informative post!!!!

[Nel2014]

I want to disable bulb checks on startup, how do i do this?

[n00b17]

So I have a 2011 E90 with xenon lamps and AEs
I wanted to increase the AE brightness, and I read/was told that I would have to code via nettodat to achieve that.

I got the nettodat.trc for my NFRM module using the NCS-Expert. Then in NCS Dummy the hex values for PWM_SL_1_FKT_BL_TFL & PWM_SL_1_FKT_SL_TFL were set to custom value 0C,2C and create the nettodat.man file (A compare shows the change correctly)

Then back to NCS-Expert, coapiCodeSgByNettoData as the basic function (supplying nettodat.man as the value for the Nettodatenliste parameter)
The jobname was kept as SG_CODIEREN while executing the job, which completed successfully.

However, when I read back the NFRM module to confirm the changes, the nettodat.trc file shows the old values.

What could I be doing wrong ??
I've used different NCS Expert profiles and the result is the same.

[romelsms1]

Hi all,

Am thinking of getting someone to do my first few coding changes on my BMW e90 LCI (2011, small iDrive, light sensor) using the NCS expert to do the following bellow

Now on Auto mode and DRL on my car is like a “Christmas tree” even it is light outside: AE on, low beam on, all interior lights are on (clusters, AC panel...etc) also rear lights are on...and so the light sensor is useless (the light are always on)
1. DRL (activated form iDrive and lights in Auto mode):
• DRL on and daylight outside: Light only AE (on high brightness) + fog light....without interior or rear light
• DRL on with poor light or night outside: turn on low beam, AE (normal brightness), interior and rear light also on, fog light off
2. Light sensor sensibility
• I found on the internet that can be adjust from iDrive (did anybody try it?)
In KOMBI module:
MMI_ENA_PIA --> aktiv
MMI_ENA_RPA_RDC --> aktiv
LICHT_AUT_WERT_1 --> aktiv
LICHT_AUT_WERT_2 --> aktiv
LICHT_AUT_WERT_3 --> aktiv
3. Cornering light using fog light
• There is any possibility to code the car in order to turn on the fog lights (left/right) – The car doesn’t have xenon or adaptive low/high beams

Can you help me the rights code or other information?
Thank you in advance

[S4NoMore]

I have INPA, the BMW Coding Tool, and NCS-Expert installed. I've confirmed using INPA that the cable works with my car. However, in NCS I only see the default profile option. What have I done wrong? NCS is also all in German but I could deal with that I think. Thanks for any advice.

[Spydeputy]

Originally Posted by xxxjecxxx

still investigating if it can be coded otherwise but I have coded mine to close if rain is detected, the only thing i've noticed is that the auto wipers have to be enabled

Do you have a list of what CAN be coded on my 2008 E90 335xi?

[ctuna]

http://www.google.com/url?sa=t&rct=j...,d.cGE&cad=rja

[ProAktion]

I would like the gauges in my 2008 e90 to do a full test sweep at startup. Anyone got any coding ideas for that?

[ProAktion]

Originally Posted by BimmerGeeks

Jb4

I haven't looked into the jb4, or where to get it. Will the Carly app do it?

Edit: I found out about the jb4 with a little searching. Thanks BimmerGeeks!

[ProAktion]

That's what I have but not gonna spend that monies just for a gauge aweep.

[roadkillrob]

Burger also made something called the cantool that just gave you a bunch of can bus things like the JB4 but no tuning, was pretty cheap but they stopped making it - if you can find a used one, it will give you gauge sweep.